970f1914be
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
43 lines
1.2 KiB
Bash
Executable file
43 lines
1.2 KiB
Bash
Executable file
#!/bin/sh
|
|
#
|
|
# Copyright (C) 2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
|
|
board_config_update
|
|
|
|
board=$(board_name)
|
|
boardname="${board##*,}"
|
|
|
|
case "$board" in
|
|
asus,rt-ac58u)
|
|
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2G" "phy0tpt"
|
|
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:blue:wlan5G" "phy1tpt"
|
|
ucidef_set_led_usbport "usb" "USB" "${boardname}:blue:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1"
|
|
ucidef_set_led_netdev "wan" "WAN" "${boardname}:blue:wan" "eth1"
|
|
ucidef_set_led_switch "lan" "LAN" "${boardname}:blue:lan" "switch0" "0x1e"
|
|
;;
|
|
avm,fritzbox-4040)
|
|
ucidef_set_led_wlan "wlan" "WLAN" "fritz4040:green:wlan" "phy0tpt" "phy1tpt"
|
|
ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
|
|
ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
|
|
;;
|
|
glinet,gl-b1300)
|
|
ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
|
|
;;
|
|
netgear,ex6100v2 |\
|
|
netgear,ex6150v2)
|
|
ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt"
|
|
ucidef_set_led_wlan "wlan5g" "WLAN5G" "ex61x0v2:green:client" "phy1tpt"
|
|
;;
|
|
meraki,mr33)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
*)
|
|
;;
|
|
esac
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|