openwrtv4/package/uboot-kirkwood/files/board/Marvell/iconnect/kwbimage.cfg
2010-10-04 21:26:33 +00:00

162 lines
5.2 KiB
INI

#
# (C) Copyright 2009
# Marvell Semiconductor <www.marvell.com>
# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
# MA 02110-1301 USA
#
# Refer docs/README.kwimage for more details about how-to configure
# and create kirkwood boot image
#
# Boot Media configurations
BOOT_FROM nand
NAND_ECC_MODE default
NAND_PAGE_SIZE 0x0800
# SOC registers configuration using bootrom header extension
# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
# Configure RGMII-0 interface pad voltage to 1.8V
DATA 0xFFD100e0 0x1b1b1b9b
#Dram initalization for SINGLE x16 CL=5 @ 400MHz
DATA 0xFFD01400 0x43000c30 # DDR Configuration register
# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
# bit23-14: zero
# bit24: 1= enable exit self refresh mode on DDR access
# bit25: 1 required
# bit29-26: zero
# bit31-30: 01
DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
# bit 4: 0=addr/cmd in smame cycle
# bit 5: 0=clk is driven during self refresh, we don't care for APX
# bit 6: 0=use recommended falling edge of clk for addr/cmd
# bit14: 0=input buffer always powered up
# bit18: 1=cpu lock transaction enabled
# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
# bit30-28: 3 required
# bit31: 0=no additional STARTBURST delay
DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
# bit3-0: TRAS lsbs
# bit7-4: TRCD
# bit11- 8: TRP
# bit15-12: TWR
# bit19-16: TWTR
# bit20: TRAS msb
# bit23-21: 0x0
# bit27-24: TRRD
# bit31-28: TRTP
DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
# bit6-0: TRFC
# bit8-7: TR2R
# bit10-9: TR2W
# bit12-11: TW2W
# bit31-13: zero required
DATA 0xFFD01410 0x000000cc # DDR Address Control
# bit1-0: 00, Cs0width=x8
# bit3-2: 11, Cs0size=1Gb
# bit5-4: 00, Cs1width=x8
# bit7-6: 11, Cs1size=1Gb
# bit9-8: 00, Cs2width=nonexistent
# bit11-10: 00, Cs2size =nonexistent
# bit13-12: 00, Cs3width=nonexistent
# bit15-14: 00, Cs3size =nonexistent
# bit16: 0, Cs0AddrSel
# bit17: 0, Cs1AddrSel
# bit18: 0, Cs2AddrSel
# bit19: 0, Cs3AddrSel
# bit31-20: 0 required
DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
# bit0: 0, OpenPage enabled
# bit31-1: 0 required
DATA 0xFFD01418 0x00000000 # DDR Operation
# bit3-0: 0x0, DDR cmd
# bit31-4: 0 required
DATA 0xFFD0141C 0x00000C52 # DDR Mode
# bit2-0: 2, BurstLen=2 required
# bit3: 0, BurstType=0 required
# bit6-4: 4, CL=5
# bit7: 0, TestMode=0 normal
# bit8: 0, DLL reset=0 normal
# bit11-9: 6, auto-precharge write recovery ????????????
# bit12: 0, PD must be zero
# bit31-13: 0 required
DATA 0xFFD01420 0x00000040 # DDR Extended Mode
# bit0: 0, DDR DLL enabled
# bit1: 0, DDR drive strenght normal
# bit2: 0, DDR ODT control lsd (disabled)
# bit5-3: 000, required
# bit6: 1, DDR ODT control msb, (disabled)
# bit9-7: 000, required
# bit10: 0, differential DQS enabled
# bit11: 0, required
# bit12: 0, DDR output buffer enabled
# bit31-13: 0 required
DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
# bit2-0: 111, required
# bit3 : 1 , MBUS Burst Chop disabled
# bit6-4: 111, required
# bit7 : 0
# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
# bit9 : 0 , no half clock cycle addition to dataout
# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
# bit15-12: 1111 required
# bit31-16: 0 required
DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
# bit0: 1, Window enabled
# bit1: 0, Write Protect disabled
# bit3-2: 00, CS0 hit selected
# bit23-4: ones, required
# bit31-24: 0x0F, Size (i.e. 256MB)
DATA 0xFFD01508 0x00000000 # CS[1]n Base address to 256Mb
DATA 0xFFD0150C 0x00000000 # CS[1]n Size 256Mb Window enabled for CS1
DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low)
DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
# bit3-2: 01, ODT1 active NEVER!
# bit31-4: zero, required
DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
DATA 0xFFD01480 0x00000001 # DDR Initialization Control
#bit0=1, enable DDR init upon this register write
# End of Header extension
DATA 0x0 0x0