5b7b0c68c7
Add initial support for cortex-a72 based Armada DB-88F8040-Modular and
DB-88F7040-Modular development boards.
DB-88F8040-Modular specifications:
- Quad-core ARMv8 Cortex A72 CPU (up to 2 GHz)
- DDR4 DIMM - 64 bits + ECC
- 2 x 128 Mb SPI NOR flash memory
- 2 x 1G Ethernet port via RGMII (RJ45)
- 2 x SD card ports (4 bit port on CP, 8 bit port on AP)
- 2 SERDES modules with the following interfaces each:
- 2 x SATA Rev 3.0 port (Port1 via SERDES module CON4 (active port), Port0
via SERDES Module CON2 or CON1 (optional port))
- 3 x PCI Express (PCIe) Gen 3.0 (Port2 via SERDES module CON5 (active port),
Port1 via SERDES module CON7 (optional port), Port0 via SERDES module CON6
(optional port))
- 2 x USB3 (USB 2.0 backward compatible) host (via SERDES module CON9 and
CON10)
- 1 x 10G port over SFP+ connector (via SERDES module CON8)
- 1 x MCI interface by two over USB Type C connector
- 4 x serial COM port driven by the 88F8040 UART interface and converted to
USB via FTDI IC
- I2C Master Interface
- CP I2C 2x EEPROM @ Address 0x50 and 0x57
- 1 x I/O Expander @ Address 0x21
- Sample at Reset (SatR) memory device @ Address 0x4C and 0x4E
- I2C Slave Interface (via SERDES module) - Connection to each device on the
board via an I2C multiplexer
- JTAG interface for CPU emulator
- Board dimensions: 270 mm x 240 mm (main + SERDES module)
- SERDES Module Dimensions: 70 mm x 105 mm
DB-88F7040-Modular specifications:
- Quad-core ARMv8 Cortex A72 CPU
- CPU core operating speed of up to 1.6 GHz for Dual Core, 1.4 GHz for Quad
Core
- DDR4 - 32 bit + ECC on Module - SLM1366-V1 (DB-DDR4-40B-MODULE) 4 GByte
32-bit
- 1 x 128Mb SPI NOR flash memory
- 2 x 1G Ethernet port: 1 over RGMII (RJ45) and 1 over SGMII
- SD card 4 bits port on AP
- eMMc Module on CP
- 1 SERDES Modules with the following interfaces each:
- 1 x SATA Rev 3.0 port (via SERDES module CON4)
- 1 x PCI Express (PCIe) Gen 3.0 (via SERDES module CON5)
- 2 x USB 3.0 (USB 2.0 backward compatible) host (via SERDES module CON9 and
CON10)
- 1 x 10G port over SFP+ connector (via SERDES module CON8)
- 2 x MCi interface by one over USB Type C connector
- 4 x Serial COM port driven by the 88F7040 UA
- RT interface and converted to USB via FTDI IC
- I2C Master Interface
- 2 x EEPROM at address 0x57 and 0x50 in AP and 2 x EEPROM at address 0x57
and 0x50 in CP
- 1 x I/O Expander at address 0x21
- Sample at Reset (SatR) memory device at address 0x4C and 0x4E
- I2C Slave Interface (via SERDES module) - Connection to each device on the
board via an I2C multiplexer
- JTAG interface for CPU emulator
- Board dimensions - 270 mm x 240 mm (main + SERDES module)
- SERDES Module Dimensions - 70 mm x 105 mm
Booting from USB flash drive (dd sdcard image to the flash drive):
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot manually (make sure to set correct dtb file name):
setenv bootargs_root 'root=/dev/sda2 rw rootdelay=2 ip=dhcp'
setenv fdtfile armada-7040-db.dtb
setenv image_name Image
setenv bootcmd 'usb start; ext4load usb 0:1 $kernel_addr $image_name; ext4load usb 0:1 $fdt_addr $fdtfile; setenv bootargs $console $mtdparts $bootargs_root; booti $kernel_addr - $fdt_addr'
saveenv
boot
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
|
||
|---|---|---|
| .. | ||
| 01_leds | ||
| 02_network | ||