openwrtv4/target/linux/layerscape/patches-4.4/1097-mtd-fsl-quadspi-use-the-property-fields-of-SPI-NOR.patch
Yutang Jiang 15a14cf166 layerscape: add 64b/32b target for ls1012ardb device
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.

The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.

Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
2016-10-31 17:00:10 +01:00

87 lines
2.7 KiB
Diff

From 5c315652c1b43a6a3abe48c2842cde822ac0ff3c Mon Sep 17 00:00:00 2001
From: Yunhui Cui <B56489@freescale.com>
Date: Wed, 20 Jan 2016 18:40:31 +0800
Subject: [PATCH 097/113] mtd:fsl-quadspi:use the property fields of SPI-NOR
We can get the read/write/erase opcode from the spi nor framework
directly. This patch uses the information stored in the SPI-NOR to
remove the hardcode in the fsl_qspi_init_lut().
Signed-off-by: Yunhui Cui <B56489@freescale.com>
---
drivers/mtd/spi-nor/fsl-quadspi.c | 40 +++++++++++--------------------------
1 file changed, 12 insertions(+), 28 deletions(-)
--- a/drivers/mtd/spi-nor/fsl-quadspi.c
+++ b/drivers/mtd/spi-nor/fsl-quadspi.c
@@ -373,9 +373,13 @@ static void fsl_qspi_init_lut(struct fsl
void __iomem *base = q->iobase;
int rxfifo = q->devtype_data->rxfifo;
u32 lut_base;
- u8 cmd, addrlen, dummy;
int i;
+ struct spi_nor *nor = &q->nor[0];
+ u8 addrlen = (nor->addr_width == 3) ? ADDR24BIT : ADDR32BIT;
+ u8 read_op = nor->read_opcode;
+ u8 read_dm = nor->read_dummy;
+
fsl_qspi_unlock_lut(q);
/* Clear all the LUT table */
@@ -385,20 +389,10 @@ static void fsl_qspi_init_lut(struct fsl
/* Quad Read */
lut_base = SEQID_QUAD_READ * 4;
- if (q->nor_size <= SZ_16M) {
- cmd = SPINOR_OP_READ_1_1_4;
- addrlen = ADDR24BIT;
- dummy = 8;
- } else {
- /* use the 4-byte address */
- cmd = SPINOR_OP_READ_1_1_4;
- addrlen = ADDR32BIT;
- dummy = 8;
- }
-
- qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+ qspi_writel(q, LUT0(CMD, PAD1, read_op) | LUT1(ADDR, PAD1, addrlen),
base + QUADSPI_LUT(lut_base));
- qspi_writel(q, LUT0(DUMMY, PAD1, dummy) | LUT1(FSL_READ, PAD4, rxfifo),
+ qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
+ LUT1(FSL_READ, PAD4, rxfifo),
base + QUADSPI_LUT(lut_base + 1));
/* Write enable */
@@ -409,16 +403,8 @@ static void fsl_qspi_init_lut(struct fsl
/* Page Program */
lut_base = SEQID_PP * 4;
- if (q->nor_size <= SZ_16M) {
- cmd = SPINOR_OP_PP;
- addrlen = ADDR24BIT;
- } else {
- /* use the 4-byte address */
- cmd = SPINOR_OP_PP;
- addrlen = ADDR32BIT;
- }
-
- qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+ qspi_writel(q, LUT0(CMD, PAD1, nor->program_opcode) |
+ LUT1(ADDR, PAD1, addrlen),
base + QUADSPI_LUT(lut_base));
qspi_writel(q, LUT0(FSL_WRITE, PAD1, 0),
base + QUADSPI_LUT(lut_base + 1));
@@ -432,10 +418,8 @@ static void fsl_qspi_init_lut(struct fsl
/* Erase a sector */
lut_base = SEQID_SE * 4;
- cmd = q->nor[0].erase_opcode;
- addrlen = q->nor_size <= SZ_16M ? ADDR24BIT : ADDR32BIT;
-
- qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+ qspi_writel(q, LUT0(CMD, PAD1, nor->erase_opcode) |
+ LUT1(ADDR, PAD1, addrlen),
base + QUADSPI_LUT(lut_base));
/* Erase the whole chip */