86e18f6706
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
124 lines
2.6 KiB
Bash
124 lines
2.6 KiB
Bash
#!/bin/sh
|
|
|
|
ath10kcal_die() {
|
|
echo "ath10cal: " "$*"
|
|
exit 1
|
|
}
|
|
|
|
ath10kcal_from_file() {
|
|
local source=$1
|
|
local offset=$2
|
|
local count=$3
|
|
|
|
dd if=$source of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $source"
|
|
}
|
|
|
|
ath10kcal_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_chardev $part)
|
|
[ -n "$mtd" ] || \
|
|
ath10kcal_die "no mtd device found for partition $part"
|
|
|
|
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $mtd"
|
|
}
|
|
|
|
ath10kcal_patch_mac() {
|
|
local mac=$1
|
|
|
|
[ -z "$mac" ] && return
|
|
|
|
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
|
|
}
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board=$(board_name)
|
|
|
|
|
|
case "$FIRMWARE" in
|
|
"ath10k/pre-cal-ahb-a000000.wifi.bin")
|
|
case "$board" in
|
|
avm,fritzbox-4040)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
|
;;
|
|
openmesh,a42)
|
|
ath10kcal_extract "0:ART" 4096 12064
|
|
;;
|
|
qcom,ap-dk01.1-c1)
|
|
ath10kcal_extract "ART" 4096 12064
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-ahb-a800000.wifi.bin")
|
|
case "$board" in
|
|
avm,fritzbox-4040)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
|
;;
|
|
openmesh,a42)
|
|
ath10kcal_extract "0:ART" 20480 12064
|
|
;;
|
|
qcom,ap-dk01.1-c1)
|
|
ath10kcal_extract "ART" 20480 12064
|
|
;;
|
|
esac
|
|
;;
|
|
|
|
"ath10k/pre-cal-pci-0000:01:00.0.bin")
|
|
case $board in
|
|
linksys,ea8500)
|
|
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
|
ath10kcal_extract "art" 4096 12064
|
|
;;
|
|
netgear,d7800 |\
|
|
netgear,r7500v2 |\
|
|
netgear,r7800)
|
|
ath10kcal_extract "art" 4096 12064
|
|
;;
|
|
tplink,c2600)
|
|
ath10kcal_extract "radio" 4096 12064
|
|
# ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 8) -1)
|
|
;;
|
|
tplink,vr2600v)
|
|
ath10kcal_extract "ART" 4096 12064
|
|
;;
|
|
zyxel,nbg6817)
|
|
ath10kcal_extract "0:ART" 4096 12064
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-pci-0001:01:00.0.bin")
|
|
case $board in
|
|
linksys,ea8500)
|
|
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
|
ath10kcal_extract "art" 20480 12064
|
|
;;
|
|
netgear,d7800 |\
|
|
netgear,r7500v2 |\
|
|
netgear,r7800)
|
|
ath10kcal_extract "art" 20480 12064
|
|
;;
|
|
tplink,c2600)
|
|
ath10kcal_extract "radio" 20480 12064
|
|
# ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 8) -2)
|
|
;;
|
|
tplink,vr2600v)
|
|
ath10kcal_extract "ART" 20480 12064
|
|
;;
|
|
zyxel,nbg6817)
|
|
ath10kcal_extract "0:ART" 20480 12064
|
|
;;
|
|
esac
|
|
;;
|
|
*)
|
|
exit 1
|
|
;;
|
|
esac
|