31469aebd4
This commit adds support for the ROSINSON WR818 WiFi-Router
SoC: Qualcomm Atheros QCA9563,
FLASH: Winbond W25Q128FV 16MBytes,
WiFi: QCA9563 b/g/n 3x3 450Mbit/s,
USB: 1x USB 2.0 Type A, 1x USB2.0 Type C,
IN: WPS/Reset button GPIO1,
OUT: Power LED red, Internet LED red, WLAN LED red,
LAN1 LED red, LAN2 LED red, System LED red,
UART: RX-GPIO18, TX-GPIO22,
Tested and working:
- Ethernet (LAN + WAN)
- WiFi
- OpenWRT sysupgrade
- Button
- LEDs
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.1.1
- Go to "Administration" -> "Firmware Upgrade"
- Upload the OpenWrt sysupgrade image
Signed-off-by: Rosy Song <rosysong@rosinson.com>
162 lines
2.3 KiB
Text
162 lines
2.3 KiB
Text
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
/ {
|
|
model = "ROSINSON WR818";
|
|
compatible = "rosinson,wr818", "qca,qca9560";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
aliases {
|
|
led-boot = &system;
|
|
led-failsafe = &system;
|
|
led-running = &system;
|
|
led-upgrade = &system;
|
|
};
|
|
|
|
gpio_leds: leds {
|
|
compatible = "gpio-leds";
|
|
|
|
system: system {
|
|
label = "wr818:red:system";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wifi_2g {
|
|
label = "wr818:red:wifi2g";
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
num-cs = <1>;
|
|
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x050000 0xf80000>;
|
|
};
|
|
|
|
info: partition@fd0000 {
|
|
label = "factory";
|
|
reg = <0xfd0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy-mask = <0>;
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "sgmii";
|
|
|
|
qca,ar8327-initvals = <
|
|
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&info 0x0>;
|
|
phy-mode = "sgmii";
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
mtd-cal-data = <&art 0x1000>;
|
|
};
|
|
|
|
&usb_phy0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|
|
|
|
&usb_phy1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|