openwrtv4/target/linux/ramips/base-files/etc/board.d/02_network
Kristian Evensen 80829022b0 ramips: add support for the HNET C108
The HNET C108
(http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a
mifi based on MT7602A, which has the following specifications:

* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port. Only power is connected, this port is meant for
charging other devices.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
* 6000 mAh battery.
* 5x controllable LEDs.

Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).

Not working (also applies to the factory firmware):
* Wifi LED. It is always switched on, there is no relation to the
up/down state or activity of the wireless interface.

Not tested:
* SD card reader.

Notes:
* The C108 has no dedicated status LED. I therefore set the LAN LED as
status LED.

Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.

Recovery:
If you brick the device, the C108 supports recovery using TFTP. Keep the
reset button pressed for ~5sec when booting to trigger TFTP. Set the
address of the network interface on your machine to 10.10.10.3/24, and
rename your image file to Kernal.bin.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-09-09 09:55:13 +02:00

526 lines
9.9 KiB
Bash
Executable file

#!/bin/sh
. /lib/functions.sh
. /lib/functions/uci-defaults.sh
. /lib/functions/system.sh
ramips_setup_rt3x5x_vlans()
{
if [ ! -x /sbin/swconfig ]; then
# legacy default
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
return
fi
local wanports=""
local lanports=""
for port in 5 4 3 2 1 0; do
if [ `swconfig dev rt305x port $port get disable` = "1" ]; then
continue
fi
if [ `swconfig dev rt305x port $port get lan` = "0" ]; then
wanports="$port:wan $wanports"
else
lanports="$port:lan $lanports"
fi
done
ucidef_add_switch "rt305x" $lanports $wanports "6t@eth0"
}
ramips_setup_interfaces()
{
local board="$1"
case $board in
11acnas|\
w2914nsv2|\
zbt-we2026)
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan:5" "6@eth0"
;;
3g150b|\
3g300m|\
a5-v11|\
all0256n-4M|\
all0256n-8M|\
all5002|\
all5003|\
broadway|\
dcs-930|\
dcs-930l-b1|\
ht-tm02|\
linkits7688 | \
linkits7688d | \
m2m|\
microwrt|\
mpr-a2|\
ncs601w|\
omega2 | \
omega2p | \
timecloud|\
w150m|\
widora-neo|\
wnce2001|\
zbt-cpe102|\
zte-q7)
ucidef_add_switch "switch0"
ucidef_add_switch_attr "switch0" "enable" "false"
ucidef_set_interface_lan "eth0"
;;
mlw221|\
mr-102n)
ucidef_set_interface_lan "eth0.2"
;;
3g-6200n|\
ai-br100|\
d240|\
db-wrt01|\
dir-300-b7|\
dir-320-b1|\
dir-610-a1|\
dir-615-h1|\
ew1200|\
firewrt|\
hc5661a|\
hc5962|\
hlk-rm04|\
k2p|\
kn|\
kn_rc|\
mac1200rv2|\
miwifi-mini|\
miwifi-nano|\
mt7621|\
mt7628|\
mzk-750dhp|\
mzk-w300nh2|\
nixcore-x1-8M|\
nixcore-x1-16M|\
oy-0001|\
pbr-m1|\
psg1208|\
psg1218a|\
r6220|\
sap-g3200u3|\
sk-wb8|\
vr500|\
wf-2881|\
witi|\
wl-wn575a3|\
wndr3700v5|\
wt1520-4M|\
wt1520-8M|\
y1|\
youku-yk1|\
zbt-ape522ii|\
zbt-we1326|\
zbt-we826-16M|\
zbt-we826-32M|\
zbt-wg2626|\
zbt-wg3526-16M|\
zbt-wg3526-32M|\
zbt-wr8305rt)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
;;
mir3g)
ucidef_add_switch "switch0" \
"1:wan" "2:lan:2" "3:lan:1" "6@eth0"
;;
psg1218b)
ucidef_add_switch "switch0" \
"0:lan:3" "1:lan:2" "2:lan:1" "3:wan" "6@eth0"
;;
whr-300hp2|\
whr-600d|\
wsr-1166|\
wsr-600)
ucidef_add_switch "switch0" \
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "4:wan:5" "6@eth0"
;;
ar670w|\
ar725w|\
rt-ac51u)
ucidef_add_switch "switch0" \
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
;;
rt-n15|\
wl-351)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0"
;;
asl26555-8M|\
asl26555-16M|\
rp-n53)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
;;
atp-52b|\
awm002-evb-4M|\
awm002-evb-8M|\
c20i|\
dir-645|\
f5d8235-v2|\
gl-mt300a|\
gl-mt300n|\
gl-mt750|\
hg255d|\
jhr-n805r|\
jhr-n825r|\
jhr-n926r|\
mzk-wdpr|\
rb750gr3|\
rt-n14u|\
tl-wr840n-v4|\
tl-wr841n-v13|\
ubnt-erx|\
ubnt-erx-sfp|\
ur-326n4g|\
wrtnode|\
wrtnode2p | \
wrtnode2r | \
wt3020-4M|\
wt3020-8M|\
zbt-wa05)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
;;
c50)
ucidef_add_switch "switch0" \
"1:lan:3" "2:lan:4" "3:lan:1" "4:lan:2" "0:wan" "6@eth0"
;;
dir-860l-b1)
ucidef_add_switch "switch0" \
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0"
;;
gb-pc1)
ucidef_add_switch "switch0" \
"0:lan" "4:lan" "6@eth0"
;;
gl-mt300n-v2)
ucidef_add_switch "switch0" \
"1:lan" "0:wan" "6@eth0"
;;
awapn2403)
ucidef_add_switch "switch0" \
"0:lan" "1:wan" "6@eth0"
;;
b2c|\
nw718|\
psr-680w|\
sl-r7205|\
ur-336un|\
w502u|\
wr6202)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
;;
br-6475nd)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
;;
c108|\
cf-wr800n)
ucidef_add_switch "switch0" \
"4:lan" "6t@eth0"
;;
cy-swr1100)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "9@eth0"
;;
cs-qr10|\
d105|\
dch-m225|\
ex2700|\
ex3700|\
hpm|\
mzk-ex300np|\
mzk-ex750np|\
na930|\
pbr-d1|\
wli-tx4-ag300n|\
wmdr-143n|\
wmr-300|\
wn3000rpv3|\
wrh-300cr)
ucidef_set_interface_lan "eth0"
;;
duzun-dm06)
ucidef_add_switch "switch0" \
"1:lan" "0:wan" "6@eth0"
;;
e1700|\
mt7620a_mt7530)
ucidef_add_switch "switch1" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
;;
hc5*61|\
y1s)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "5:lan" "0:wan" "6@eth0"
;;
kn_rf)
ucidef_add_switch "switch0" \
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6@eth0"
;;
kng_rc)
ucidef_add_switch "switch1" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "7t@eth0"
;;
mlwg2|\
wizard8800|\
wl-330n)
ucidef_set_interface_lan "eth0.1"
;;
mr200)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "6t@eth0"
ucidef_set_interface_wan "usb0"
;;
mzk-dp150n|\
vocore-8M|\
vocore-16M)
ucidef_add_switch "switch0" \
"0:lan" "4:lan" "6t@eth0"
;;
newifi-d1)
ucidef_add_switch "switch0" \
"1:lan:2" "2:lan:1" "4:wan" "6@eth0"
;;
re350-v1)
ucidef_add_switch "switch0" \
"0:lan" "6@eth0"
;;
re6500)
ucidef_add_switch "switch0" \
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "6@eth0"
;;
rt-n56u)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "8@eth0"
;;
tew-638apb-v2)
ucidef_add_switch "switch0" \
"4:lan" "6@eth0"
;;
tew-691gr|\
tew-692gr|\
wlr-6000)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0"
;;
vocore2|\
vocore2lite)
ucidef_add_switch "switch0" \
"0:lan" "2:lan" "6t@eth0"
;;
f5d8235-v1|\
tew-714tru|\
v11st-fe|\
wzr-agl300nh)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
;;
wcr-1166ds)
ucidef_add_switch "switch0" \
"3:lan" "4:wan" "6@eth0"
;;
wcr-150gn)
ucidef_add_switch "switch0" \
"0:lan" "6t@eth0"
;;
whr-1166d)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "5:wan" "6@eth0"
;;
wizfi630a)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "0:wan" "6@eth0"
;;
*)
RT3X5X=`cat /proc/cpuinfo | egrep "(RT3.5|RT5350)"`
if [ -n "${RT3X5X}" ]; then
ramips_setup_rt3x5x_vlans
else
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
fi
;;
esac
}
ramips_setup_macs()
{
local board="$1"
local lan_mac=""
local wan_mac=""
case $board in
a5-v11|\
ht-tm02|\
wmdr-143n)
lan_mac=$(cat /sys/class/net/eth0/address)
;;
all0239-3g|\
carambola|\
freestation5|\
w502u|\
wnce2001)
wan_mac=$(mtd_get_mac_binary factory 46)
;;
bc2|\
broadway|\
d105|\
dir-300-b7|\
dir-320-b1|\
dir-620-a1|\
esr-9753|\
freestation5|\
hlk-rm04|\
mpr-a1|\
psr-680w|\
sl-r7205|\
y1|\
y1s)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_setbit_la "$lan_mac")
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
br-6475nd)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(mtd_get_mac_binary devdata 7)
;;
cy-swr1100|\
dch-m225)
lan_mac=$(mtd_get_mac_ascii factory lanmac)
;;
dir-645)
lan_mac=$(mtd_get_mac_ascii nvram lanmac)
wan_mac=$(mtd_get_mac_ascii nvram wanmac)
;;
dir-860l-b1)
lan_mac=$(mtd_get_mac_ascii factory lanmac)
wan_mac=$(mtd_get_mac_ascii factory wanmac)
;;
e1700)
wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR)
;;
gl-mt300n-v2)
wan_mac=$(mtd_get_mac_binary factory 4)
;;
hc5*61|\
hc5661a|\
hc5962)
lan_mac=`mtd_get_mac_ascii bdinfo "Vfac_mac "`
[ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
kn_rc|\
kn_rf|\
kng_rc)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
linkits7688 | \
linkits7688d)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$(mtd_get_mac_binary factory 46)
;;
mac1200rv2)
lan_mac=$(mtd_get_mac_binary factory_info 13)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
mir3g)
lan_mac=$(mtd_get_mac_binary Factory e006)
;;
miwifi-mini)
wan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_setbit_la "$wan_mac")
;;
m3|\
m4-4M|\
m4-8M|\
x5|\
x8)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_add "$lan_mac" -2)
;;
newifi-d1)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_add "$lan_mac" 2)
;;
omega2|\
omega2p)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$(mtd_get_mac_binary factory 46)
;;
oy-0001)
lan_mac=$(mtd_get_mac_binary factory 40)
wan_mac=$(mtd_get_mac_binary factory 46)
;;
r6220)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$(macaddr_add "$wan_mac" 1)
;;
rt-n56u)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_setbit_la "$lan_mac")
wan_mac=$(mtd_get_mac_binary factory 32772)
;;
sk-wb8)
wan_mac=$(mtd_get_mac_binary factory 57350)
;;
tew-691gr)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 3)
;;
tew-692gr)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 1)
;;
tiny-ac)
lan_mac=$(mtd_get_mac_ascii u-boot-env LAN_MAC_ADDR)
wan_mac=$(mtd_get_mac_ascii u-boot-env WAN_MAC_ADDR)
;;
vr500)
lan_mac=$(mtd_get_mac_binary factory 57344)
wan_mac=$(mtd_get_mac_binary factory 57350)
;;
w306r-v20)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 5)
;;
wcr-1166ds|\
wsr-1166)
local index="$(find_mtd_index "board_data")"
wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
lan_mac=$wan_mac
;;
wcr-150gn)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
whr-1166d|\
whr-300hp2|\
whr-600d|\
wsr-600)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$wan_mac
;;
wizfi630a)
lan_mac=$(mtd_get_mac_binary factory 4)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
wlr-6000)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 32772)" 2)
;;
*)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
esac
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
}
board_config_update
board=$(board_name)
ramips_setup_interfaces $board
ramips_setup_macs $board
board_config_flush
exit 0