4f74957584
This adds the patches to get fairly complete Gemini support
using kernel v4.14. It is mainly a backport of patches from
kernel v4.16 with omissions of things like graphics that require
substantial changes and will be better handled once we move
to the v4.16 kernel proper.
On top of this are some WIP patches for USB support.
Tested on Raidsonic NAS4220B and D-link DNS-313.
ChangeLog v4->v5:
- Fix ethernet single gmac usecase
- Fix USB reset (patch from Hans)
- Fix Raidsonic ethernet skew delay
- Fix kernel config (bridge, squashfs, jffs2, usb)
- Disable second usb port on Raidsonic board until fotg210_hcd is fixed
ChangeLog v3->v4:
- Make sure to use tabs rather than spaces in base-files.
- Use the dns313 image tool from the firmware-utils.
- Break out the addition of the v4.14 patches and the removal
of the v4.4 patches to separate (big) patches.
ChangeLog v2->v3:
- Update the kernel config as indicated by Hauke Martens:
- Regenerate again after rebasing using kernel_oldconfig
dropping a few optimization settings that are now generic
- Drop CFG80211 stuff (module)
- Drop CIFS stuff (module)
- Drop MAC80211 (module)
- Drop wireless drivers (module)
- Enabled OverlayFS
- Added proper DNS-313 boot image generation with the special
file header tool.
- Disable CMA in the kernel
- Enable LZMA compression of the kernel
- Consequently name the nas4220b images nas4220b
- Update preinit MAC detection script to handle also DNS-313
- Add board.d/03_hdparm to set the disk to spin down after
1 minute by default, if we have the hdparm tool installed
ChangeLog v1->v2:
- Processed config through kernel_oldconfig
- Processed patches through make target/linux/{clean,refresh} V=99
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
36 lines
1.2 KiB
Diff
36 lines
1.2 KiB
Diff
From f30cc6acdeb834be1a6ae54d47c84b2f8012b83d Mon Sep 17 00:00:00 2001
|
|
From: Linus Walleij <linus.walleij@linaro.org>
|
|
Date: Thu, 18 Jan 2018 14:36:21 +0100
|
|
Subject: [PATCH 25/31] ARM: dts: Set D-Link DNS-313 SATA to muxmode 0
|
|
|
|
This stops the driver from trying to probe the ATA slave
|
|
interface. The vendor code enables the slave interface
|
|
but the driver in the vendor tree does not make use of
|
|
it.
|
|
|
|
Setting it to muxmode 0 disables the slave interface:
|
|
the hardware only has the master interface connected
|
|
to the one harddrive slot anyways.
|
|
|
|
Without this change booting takes excessive time, so it
|
|
is very annoying to end users.
|
|
|
|
Fixes: dd5c0561db75 ("ARM: dts: Add basic devicetree for D-Link DNS-313")
|
|
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
---
|
|
ARM SoC folks: please apply this for fixes for v4.16.
|
|
---
|
|
arch/arm/boot/dts/gemini-dlink-dns-313.dts | 2 +-
|
|
1 file changed, 1 insertion(+), 1 deletion(-)
|
|
|
|
--- a/arch/arm/boot/dts/gemini-dlink-dns-313.dts
|
|
+++ b/arch/arm/boot/dts/gemini-dlink-dns-313.dts
|
|
@@ -219,7 +219,7 @@
|
|
|
|
sata: sata@46000000 {
|
|
/* The ROM uses this muxmode */
|
|
- cortina,gemini-ata-muxmode = <3>;
|
|
+ cortina,gemini-ata-muxmode = <0>;
|
|
cortina,gemini-enable-sata-bridge;
|
|
status = "okay";
|
|
};
|