9786b53efb
Remove the ephy-pins from the ethernet device tree node. The ephy-pins are useed to controll the ePHY LEDs and this board doesn't have these. Instead one of the ePHY pins is used in GPIO mode to control the WAN LED. Use the switch LED trigger to control the WAN LED. Move the power LED handling to diag.sh to show the boot status via this LED. Add the missing kernel packages for USB and microSD card reader to the default package selection. Fix the maximum image size value. The board has a 32MByte flash chip. Fixes: FS#1055 Signed-off-by: Edmunt Pienkowsky <roed@onet.eu> [make the commit message more verbose, remove GPIO pinmux for pins not used as GPIOs] Signed-off-by: Mathias Kresin <dev@kresin.me>
125 lines
1.8 KiB
Text
125 lines
1.8 KiB
Text
/dts-v1/;
|
|
|
|
#include "mt7620a.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "youku,yk1", "ralink,mt7620a-soc";
|
|
model = "YOUKU YK1";
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
wan {
|
|
label = "youku-yk1:blue:wan";
|
|
gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
air {
|
|
label = "youku-yk1:blue:air";
|
|
gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
usb {
|
|
label = "youku-yk1:blue:usb";
|
|
gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
power {
|
|
label = "youku-yk1:blue:power";
|
|
gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <20>;
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x50000 0x1fb0000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
default {
|
|
ralink,group = "i2c", "rgmii1", "ephy", "wled";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
pinctrl-names = "default";
|
|
mtd-mac-address = <&factory 0x4>;
|
|
mediatek,portmap = "llllw";
|
|
};
|
|
|
|
&wmac {
|
|
ralink,mtd-eeprom = <&factory 0>;
|
|
};
|
|
|
|
&sdhci {
|
|
status = "okay";
|
|
};
|
|
|
|
&ehci {
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci {
|
|
status = "okay";
|
|
};
|