2d8eeca842
The device has a second uart accessible via pin headers, so enable it. There is also a green power led which was not enabled previously. Enable it too and use it as status LED. Signed-off-by: Benjamin Valentin <benjamin.valentin@volatiles.de>
143 lines
2.2 KiB
Text
143 lines
2.2 KiB
Text
/dts-v1/;
|
|
|
|
#include "mt7628an.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/{
|
|
compatible = "glinet,gl-mt300n-v2", "ralink,mt7620an-soc";
|
|
model = "GL-MT300N-V2";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x8000000>;
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power {
|
|
label = "gl-mt300n-v2:green:power";
|
|
default-state = "on";
|
|
gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wan {
|
|
label = "gl-mt300n-v2:blue:wan";
|
|
gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan {
|
|
label = "gl-mt300n-v2:red:wlan";
|
|
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
BTN_0 {
|
|
label = "BTN_0";
|
|
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
};
|
|
|
|
BTN_1 {
|
|
label = "BTN_1";
|
|
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_1>;
|
|
};
|
|
};
|
|
|
|
gpio_export {
|
|
compatible = "gpio-export";
|
|
#size-cells = <0>;
|
|
|
|
usb {
|
|
gpio-export,name = "usb";
|
|
gpio-export,output = <1>;
|
|
gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "wdt", "gpio", "wled_an", "p0led_an", "p1led_an", "i2s";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
mtd-mac-address = <&factory 0x4>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
ralink,mtd-eeprom = <&factory 0x0>;
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
m25p,chunked-io = <32>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x50000 0xfb0000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ehci {
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci {
|
|
status = "okay";
|
|
};
|