openwrtv4/target/linux/lantiq/dts/EASY50810.dts
blogic b7fc892eb5 lantiq: move partitions into partion table node
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49280
2016-05-10 10:43:12 +02:00

120 lines
2.3 KiB
Text

/dts-v1/;
/include/ "ar9.dtsi"
/ {
chosen {
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
};
memory@0 {
reg = <0x0 0x2000000>;
};
fpi@10000000 {
#address-cells = <1>;
#size-cells = <1>;
localbus@0 {
#address-cells = <2>;
#size-cells = <1>;
ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
1 0 0x4000000 0x4000010>; /* addsel1 */
compatible = "lantiq,localbus", "simple-bus";
nor-boot@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x2000000>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x00000 0x10000>; /* 64 KB */
};
partition@10000 {
label = "uboot_env";
reg = <0x10000 0x10000>; /* 64 KB */
};
partition@20000 {
label = "firmware";
reg = <0x20000 0x3d0000>;
};
partition@400000 {
label = "rootfs";
reg = <0x400000 0x400000>;
};
};
};
};
gpio: pinmux@E100B10 {
compatible = "lantiq,pinctrl-xr9";
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
#gpio-cells = <2>;
gpio-controller;
reg = <0xE100B10 0xA0>;
state_default: pinmux {
stp {
lantiq,groups = "stp";
lantiq,function = "stp";
};
exin {
lantiq,groups = "exin1";
lantiq,function = "exin";
};
pci {
lantiq,groups = "gnt1";
lantiq,function = "pci";
};
conf_out {
lantiq,pins = "io4", "io5", "io6"; /* stp */
lantiq,open-drain;
lantiq,pull = <0>;
};
};
};
etop@E180000 {
compatible = "lantiq,etop-xway";
reg = <0xE180000 0x40000
0xE108000 0x200>;
interrupt-parent = <&icu0>;
interrupts = <72 73>;
phy-mode = "rmii";
mac-address = [ 00 11 22 33 44 55 ];
};
stp0: stp@E100BB0 {
#gpio-cells = <2>;
compatible = "lantiq,gpio-stp-xway";
gpio-controller;
reg = <0xE100BB0 0x40>;
lantiq,shadow = <0xfff>;
lantiq,groups = <0x3>;
};
pci@E105400 {
lantiq,bus-clock = <33333333>;
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
0x7000 0 0 1 &icu0 29 1 // slot 14, irq 29
>;
gpios-reset = <&gpio 21 0>;
req-mask = <0x1>; /* GNT1 */
};
};
};