openwrtv4/target/linux/ramips/dts/WHR-1166D.dts
Álvaro Fernández Rojas 021c893658 ramips: fix size-cells on spi nodes
size-cells should be 0 in order to avoid dummy values in reg properties.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-18 16:57:39 +02:00

170 lines
2.5 KiB
Text

/dts-v1/;
#include "mt7620a.dtsi"
/ {
compatible = "ralink,mt7620a-soc";
model = "Buffalo WHR-1166D";
gpio-leds {
compatible = "gpio-leds";
power {
label = "whr-1166d:red:power";
gpios = <&gpio0 7 1>;
};
wifi {
label = "whr-1166d:green:wifi";
gpios = <&gpio0 8 1>;
};
power2 {
label = "whr-1166d:green:power";
gpios = <&gpio0 9 1>;
};
wifi2 {
label = "whr-1166d:orange:wifi";
gpios = <&gpio0 10 1>;
};
internet {
label = "whr-1166d:green:internet";
gpios = <&gpio2 17 1>;
};
router {
label = "whr-1166d:orange:router";
gpios = <&gpio2 18 1>;
};
router2 {
label = "whr-1166d:green:router";
gpios = <&gpio2 19 1>;
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <20>;
reset {
label = "reset";
gpios = <&gpio2 12 1>;
linux,code = <0x198>;
};
aoss {
label = "aoss";
gpios = <&gpio2 13 1>;
linux,code = <0x211>;
};
ap {
label = "ap";
gpios = <&gpio2 14 1>;
linux,code = <0x100>;
linux,input-type = <5>; /* EV_SW */
};
bridge {
label = "bridge";
gpios = <&gpio2 15 1>;
linux,code = <0x100>;
linux,input-type = <5>; /* EV_SW */
};
};
};
&gpio2 {
status = "okay";
};
&spi0 {
status = "okay";
m25p80@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
linux,modalias = "m25p80", "mx25l6405d";
spi-max-frequency = <10000000>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "firmware";
reg = <0x50000 0xfb0000>;
};
};
};
&pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "i2c", "uartf", "wled", "nd_sd";
ralink,function = "gpio";
};
};
};
&ethernet {
pinctrl-names = "default";
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
port@5 {
status = "okay";
phy-handle = <&phy5>;
phy-mode = "rgmii";
};
mdio-bus {
status = "okay";
phy5: ethernet-phy@5 {
reg = <5>;
phy-mode = "rgmii";
};
};
};
&gsw {
mediatek,port4 = "ephy";
};
&wmac {
ralink,mtd-eeprom = <&factory 0>;
};
&pcie {
status = "okay";
pcie-bridge {
mt76@0,0 {
reg = <0x0000 0 0 0 0>;
device_type = "pci";
mediatek,mtd-eeprom = <&factory 32768>;
mediatek,2ghz = <0>;
};
};
};