6165e4aab0
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of TL-MR3020 (both devices use very similar enclosure, in same size). New device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 1x USB 2.0 (GPIO-controlled power) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch - UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper resitors are missing on TX/RX lines) - 1x micro USB (for power only) Flash instructions: Use "factory" image under vendor GUI. Recovery instructions: This device contains tftp recovery mode inside U-Boot. You can use it to flash LEDE (use "factory" image) or vendor firmware. 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin" to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir. 3. Connect PC with LAN port, press the reset button, power up the router and keep button pressed until WPS LED lights up. 4. Router will download file from server, write it to flash and reboot. Root access over serial line in vendor firmware: root/sohoadmin. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
148 lines
3.3 KiB
Bash
148 lines
3.3 KiB
Bash
#!/bin/sh
|
|
|
|
ath10kcal_die() {
|
|
echo "ath10cal: " "$*"
|
|
exit 1
|
|
}
|
|
|
|
ath10kcal_from_file() {
|
|
local source=$1
|
|
local offset=$2
|
|
local count=$3
|
|
|
|
dd if=$source of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $source"
|
|
}
|
|
|
|
ath10kcal_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_chardev $part)
|
|
[ -n "$mtd" ] || \
|
|
ath10kcal_die "no mtd device found for partition $part"
|
|
|
|
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $mtd"
|
|
}
|
|
|
|
ath10kcal_patch_mac() {
|
|
local mac=$1
|
|
|
|
[ -z "$mac" ] && return
|
|
|
|
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
|
|
}
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/ar71xx.sh
|
|
. /lib/functions.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board=$(ar71xx_board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"ath10k/cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
a40|\
|
|
a60|\
|
|
mr1750|\
|
|
mr1750v2|\
|
|
om5p-acv2)
|
|
ath10kcal_extract "ART" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
|
|
;;
|
|
archer-c25-v1|\
|
|
archer-c59-v1|\
|
|
archer-c60-v1|\
|
|
tl-wdr6500-v2)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -2)
|
|
;;
|
|
cf-e380ac-v1|\
|
|
cf-e380ac-v2|\
|
|
dlan-pro-1200-ac|\
|
|
sr3200|\
|
|
xd3200)
|
|
ath10kcal_extract "art" 20480 2116
|
|
;;
|
|
dap-2695-a1)
|
|
ath10kcal_extract "radiocfg" 20480 2116
|
|
ath10kcal_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
|
|
;;
|
|
dir-869-a1|\
|
|
qihoo-c301)
|
|
ath10kcal_extract "radiocfg" 20480 2116
|
|
ath10kcal_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
|
|
;;
|
|
dw33d)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(mtd_get_mac_binary art 18)
|
|
;;
|
|
epg5000|\
|
|
esr1750)
|
|
ath10kcal_extract "caldata" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
|
|
;;
|
|
mc-mac1200r)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -1)
|
|
;;
|
|
r6100)
|
|
ath10kcal_extract "caldata" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) +2)
|
|
;;
|
|
rb-952ui-5ac2nd)
|
|
ath10kcal_from_file "/sys/firmware/routerboot/ext_wlan_data" 20480 2116
|
|
;;
|
|
re450|\
|
|
tl-wr902ac-v1)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -2)
|
|
;;
|
|
tl-wpa8630)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
|
|
;;
|
|
unifiac-lite|\
|
|
unifiac-pro)
|
|
ath10kcal_extract "EEPROM" 20480 2116
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/cal-pci-0000:01:00.0.bin")
|
|
case $board in
|
|
archer-c5|\
|
|
archer-c7)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -2)
|
|
;;
|
|
nbg6616|\
|
|
nbg6716)
|
|
ath10kcal_extract "RFdata" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -2)
|
|
;;
|
|
om5p-ac)
|
|
ath10kcal_extract "ART" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
|
|
;;
|
|
rb-911g-5hpacd|\
|
|
rb-962uigs-5hact2hnt)
|
|
ath10kcal_from_file "/sys/firmware/routerboot/ext_wlan_data" 20480 2116
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
archer-c58-v1)
|
|
ath10kcal_extract "art" 20480 12064
|
|
;;
|
|
esac
|
|
;;
|
|
*)
|
|
exit 1
|
|
;;
|
|
esac
|