openwrtv4/target/linux/ipq806x/patches-3.18/700-add-gmac-dts-suport.patch
John Crispin 5d52f4b51d ipq806x: add platform usb support
This change adds DWC3 QCOM USB phys and TCSR drivers. These are
cherry-picked from the following LKML threads:
*dwc3 qcom: https://lkml.org/lkml/2014/9/12/599
*tcsr: https://lkml.org/lkml/2015/2/9/579

We're also adding an additional patch to add the corresponding dev nodes
in the IPQ806x and AP148 dts files.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45261
2015-04-03 19:06:30 +00:00

171 lines
4 KiB
Diff

--- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
+++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
@@ -22,8 +22,15 @@
linux,stdout-path = "serial0:115200n8";
};
+ aliases {
+ mdio-gpio0 = &mdio0;
+ };
+
soc {
pinmux@800000 {
+ pinctrl-0 = <&mdio0_pins &rgmii2_pins>;
+ pinctrl-names = "default";
+
i2c4_pins: i2c4_pinmux {
pins = "gpio12", "gpio13";
function = "gsbi4";
@@ -38,6 +45,25 @@
bias-none;
};
};
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
};
gsbi@16300000 {
@@ -76,6 +102,7 @@
#size-cells = <1>;
spi-max-frequency = <50000000>;
reg = <0>;
+ m25p,fast-read;
partition@0 {
label = "lowlevel_init";
@@ -136,5 +163,66 @@
usb30@1 {
status = "ok";
};
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+
+ phy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0xaa545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ device_type = "ethernet-phy";
+ reg = <4>;
+ };
+ };
+
+ nss-gmac-common {
+ reg = <0x03000000 0x0000FFFF 0x1bb00000 0x0000FFFF 0x00900000 0x00004000>;
+ reg-names = "nss_reg_base" , "qsgmii_reg_base", "clk_ctl_base";
+ };
+
+ gmac1: ethernet@37200000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,rgmii_delay = <0>;
+ qcom,emulation = <0>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ qcom,socver = <0>;
+ local-mac-address = [000000000000];
+ mdiobus = <&mdio0>;
+ };
+
+ gmac2: ethernet@37400000 {
+ status = "ok";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+ qcom,phy_mdio_addr = <0>;
+ qcom,poll_required = <0>;
+ qcom,rgmii_delay = <0>;
+ qcom,emulation = <0>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ qcom,socver = <0>;
+ local-mac-address = [000000000000];
+ mdiobus = <&mdio0>;
+ };
};
};
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -3,6 +3,7 @@
#include "skeleton.dtsi"
#include <dt-bindings/clock/qcom,gcc-ipq806x.h>
#include <dt-bindings/soc/qcom,gsbi.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
model = "Qualcomm IPQ8064";
@@ -390,5 +391,41 @@
};
};
+ nss-gmac-common {
+ reg = <0x03000000 0x0000FFFF 0x1bb00000 0x0000FFFF 0x00900000 0x00004000>;
+ reg-names = "nss_reg_base" , "qsgmii_reg_base", "clk_ctl_base";
+ };
+
+ gmac0: ethernet@37000000 {
+ device_type = "network";
+ compatible = "qcom,nss-gmac";
+ reg = <0x37000000 0x200000>;
+ interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ gmac1: ethernet@37200000 {
+ device_type = "network";
+ compatible = "qcom,nss-gmac";
+ reg = <0x37200000 0x200000>;
+ interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ gmac2: ethernet@37400000 {
+ device_type = "network";
+ compatible = "qcom,nss-gmac";
+ reg = <0x37400000 0x200000>;
+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ gmac3: ethernet@37600000 {
+ device_type = "network";
+ compatible = "qcom,nss-gmac";
+ reg = <0x37600000 0x200000>;
+ interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
};
};