openwrtv4/target/linux/ath79/dts/ar9344_ocedo_raccoon.dts
David Bauer 5409dcffbd ath79: fix OCEDO Raccoon
The OCEDO Raccoon only has one ethernet port, but currently uci sections
for WAN and LAN are created.

Additionally, newer versions of the devices U-Boot (units with SteelWRT)
set the kernel-cmdline and therefore overwrite the partition-layout.
We fix this by overwriting the cmdline supplied by the bootloader.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-07-25 08:59:33 +02:00

181 lines
2.8 KiB
Text

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar9344.dtsi"
/ {
model = "OCEDO Raccoon";
compatible = "ocedo,raccoon", "qca,ar9344";
chosen {
bootargs = "console=ttyS0,115200n8";
};
aliases {
led-status = &system;
};
leds {
compatible = "gpio-leds";
power {
label = "raccoon:green:power";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
default-state = "on";
};
wlan2g {
label = "raccoon:yellow:wlan24";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "phy0tpt";
};
system: system {
label = "raccoon:blue:sys";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
};
ath9k-leds {
compatible = "gpio-leds";
wlan5g {
label = "raccoon:red:wlan5";
gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "phy1tpt";
};
};
keys {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <20>;
reset {
linux,code = <KEY_RESTART>;
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
};
&ref {
clock-frequency = <40000000>;
};
&uart {
status = "okay";
};
&gpio {
status = "okay";
};
&spi {
num-cs = <1>;
status = "okay";
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot: partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
};
partition@50000 {
label = "firmware";
reg = <0x050000 0x740000>;
};
partition@790000 {
label = "vendor";
reg = <0x790000 0x740000>;
read-only;
};
partition@ed0000 {
label = "data";
reg = <0xed0000 0x110000>;
read-only;
};
partition@fe0000 {
label = "id";
reg = <0xfe0000 0x010000>;
read-only;
};
art: partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&pcie {
status = "okay";
ath9k: wifi@168c,0030 {
compatible = "pci168c,0030";
reg = <0x0000 0 0 0 0>;
mtd-mac-address = <&art 0xc>;
qca,no-eeprom;
#gpio-cells = <2>;
gpio-controller;
};
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&art 0x6>;
};
&mdio0 {
status = "okay";
phy-mask = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
phy-mode = "rgmii";
};
};
&eth0 {
status = "okay";
/* default for ar934x, except for 1000M */
pll-data = <0x06000000 0x00000101 0x00001616>;
mtd-mac-address = <&art 0x0>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
};