123 lines
3.2 KiB
Diff
123 lines
3.2 KiB
Diff
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
|
|
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
|
|
@@ -935,6 +935,65 @@ static struct board_info __initdata boar
|
|
},
|
|
},
|
|
};
|
|
+
|
|
+static struct board_info __initdata board_V2500V_BB = {
|
|
+ .name = "V2500V_BB",
|
|
+ .expected_cpu_id = 0x6348,
|
|
+
|
|
+ .has_uart0 = 1,
|
|
+ .has_enet0 = 1,
|
|
+ .has_enet1 = 1,
|
|
+ .has_pci = 1,
|
|
+
|
|
+ .enet0 = {
|
|
+ .has_phy = 1,
|
|
+ .use_internal_phy = 1,
|
|
+ },
|
|
+ .enet1 = {
|
|
+ .has_phy = 1,
|
|
+ .phy_id = 0,
|
|
+ .force_speed_100 = 1,
|
|
+ .force_duplex_full = 1,
|
|
+ },
|
|
+
|
|
+ .leds = {
|
|
+ {
|
|
+ .name = "V2500V_BB:green:power",
|
|
+ .gpio = 0,
|
|
+ .active_low = 1,
|
|
+ .default_trigger = "default-on",
|
|
+ },
|
|
+ {
|
|
+ .name = "V2500V_BB:red:power",
|
|
+ .gpio = 1,
|
|
+ .active_low = 1,
|
|
+ },
|
|
+ {
|
|
+ .name = "V2500V_BB:green:adsl",
|
|
+ .gpio = 2,
|
|
+ .active_low = 1,
|
|
+ },
|
|
+ { .name = "V2500V_BB:green:ppp",
|
|
+ .gpio = 3,
|
|
+ .active_low = 1,
|
|
+ },
|
|
+ {
|
|
+ .name = "V2500V_BB:green:wireless",
|
|
+ .gpio = 6,
|
|
+ .active_low = 1,
|
|
+ },
|
|
+ },
|
|
+ .buttons = {
|
|
+ {
|
|
+ .desc = "reset",
|
|
+ .gpio = 31,
|
|
+ .active_low = 1,
|
|
+ .type = EV_KEY,
|
|
+ .code = KEY_RESTART,
|
|
+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
|
|
+ },
|
|
+ },
|
|
+};
|
|
#endif /* CONFIG_BCM63XX_CPU_6348 */
|
|
|
|
/*
|
|
@@ -1675,6 +1734,7 @@ static const struct board_info __initcon
|
|
&board_96348_D4PW,
|
|
&board_spw500v,
|
|
&board_96348sv,
|
|
+ &board_V2500V_BB,
|
|
#endif
|
|
|
|
#ifdef CONFIG_BCM63XX_CPU_6358
|
|
@@ -1765,6 +1825,22 @@ void __init board_bcm963xx_init(void)
|
|
val &= MPI_CSBASE_BASE_MASK;
|
|
}
|
|
boot_addr = (u8 *)KSEG1ADDR(val);
|
|
+ printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
|
|
+
|
|
+ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
|
|
+ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
|
|
+ /* Loading firmware from the CFE Prompt always loads to Bank 0 */
|
|
+ /* Do an early check of CFE and then select bank 0 */
|
|
+
|
|
+ if (boot_addr == (u8 *)0xbf800000) {
|
|
+ u8 *tmp_boot_addr = (u8*)0xbfc00000;
|
|
+
|
|
+ bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET);
|
|
+ if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
|
|
+ printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
|
|
+ boot_addr = tmp_boot_addr;
|
|
+ }
|
|
+ }
|
|
|
|
/* dump cfe version */
|
|
cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
|
|
--- a/arch/mips/bcm63xx/dev-flash.c
|
|
+++ b/arch/mips/bcm63xx/dev-flash.c
|
|
@@ -19,6 +19,7 @@
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/spi/flash.h>
|
|
|
|
+#include <bcm63xx_board.h>
|
|
#include <bcm63xx_cpu.h>
|
|
#include <bcm63xx_dev_flash.h>
|
|
#include <bcm63xx_dev_hsspi.h>
|
|
@@ -220,6 +221,13 @@ int __init bcm63xx_flash_register(int nu
|
|
val = bcm_mpi_readl(MPI_CSBASE_REG(0));
|
|
val &= MPI_CSBASE_BASE_MASK;
|
|
|
|
+ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
|
|
+ /* Loading from CFE always uses Bank 0 */
|
|
+ if (!strcmp(board_get_name(), "V2500V_BB")) {
|
|
+ pr_info("V2500V: Start in Bank 0\n");
|
|
+ val = val + 0x400000; // Select Bank 0 start address
|
|
+ }
|
|
+
|
|
mtd_resources[0].start = val;
|
|
mtd_resources[0].end = 0x1FFFFFFF;
|
|
}
|