openwrtv4/scripts/om-fwupgradecfg-gen.sh
Sven Eckelmann 0b20490207 ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + 802.3at POE+
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 18-24V passive POE (mode B)
* powered only via POE

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

The initramfs image can be started using

  setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
  tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
  set fdt_high 0x85000000
  bootm 0x84000000

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00

99 lines
2.6 KiB
Bash
Executable file

#!/bin/sh
#
# Copyright (C) 2011 OpenWrt.org
#
# This is free software, licensed under the GNU General Public License v2.
# See /LICENSE for more information.
#
usage() {
echo "Usage: $0 <OM2P|OM5P|OM5PAC|MR600|MR900|MR1750|A60|A42|A62> <out file path> <kernel path> <rootfs path>"
rm -f $CFG_OUT
exit 1
}
[ "$#" -lt 4 ] && usage
CE_TYPE=$1
CFG_OUT=$2
KERNEL_PATH=$3
ROOTFS_PATH=$4
case $CE_TYPE in
OM2P)
MAX_PART_SIZE=7168
KERNEL_FLASH_ADDR=0x1c0000
FLASH_BS=262144
MD5_SKIP_BLOCKS=1
SIZE_FACTOR=1
SIZE_FORMAT="%d"
;;
OM5P|OM5PAC|MR600|MR900|MR1750|A60)
MAX_PART_SIZE=7808
KERNEL_FLASH_ADDR=0xb0000
FLASH_BS=65536
MD5_SKIP_BLOCKS=4
SIZE_FACTOR=1
SIZE_FORMAT="%d"
;;
A42)
MAX_PART_SIZE=15616
KERNEL_FLASH_ADDR=0x180000
FLASH_BS=65536
MD5_SKIP_BLOCKS=4
SIZE_FACTOR=1024
SIZE_FORMAT="0x%08x"
;;
A62)
MAX_PART_SIZE=15552
KERNEL_FLASH_ADDR=0x1a0000
FLASH_BS=65536
MD5_SKIP_BLOCKS=4
SIZE_FACTOR=1024
SIZE_FORMAT="0x%08x"
;;
*)
echo "Error - unsupported ce type: $CE_TYPE"
exit 1
;;
esac
CHECK_BS=65536
KERNEL_SIZE=$(stat -c%s "$KERNEL_PATH")
KERNEL_MD5=$(mkhash md5 $KERNEL_PATH)
KERNEL_SHA256=$(mkhash sha256 $KERNEL_PATH)
KERNEL_PART_SIZE_KB=$(size=$(($KERNEL_SIZE / $FLASH_BS)); [ $(($size * $FLASH_BS)) -lt $KERNEL_SIZE ] && size=$(($size + 1)); echo $(($size * $FLASH_BS / 1024)))
KERNEL_PART_SIZE=$(printf $SIZE_FORMAT $(($KERNEL_PART_SIZE_KB * $SIZE_FACTOR)))
ROOTFS_FLASH_ADDR=$(addr=$(($KERNEL_FLASH_ADDR + ($KERNEL_PART_SIZE_KB * 1024))); printf "0x%x" $addr)
ROOTFS_SIZE=$(stat -c%s "$ROOTFS_PATH")
ROOTFS_CHECK_BLOCKS=$((($ROOTFS_SIZE / $CHECK_BS) - $MD5_SKIP_BLOCKS))
ROOTFS_MD5=$(dd if=$ROOTFS_PATH bs=$CHECK_BS count=$ROOTFS_CHECK_BLOCKS 2>&- | mkhash md5)
ROOTFS_MD5_FULL=$(mkhash md5 $ROOTFS_PATH)
ROOTFS_SHA256_FULL=$(mkhash sha256 $ROOTFS_PATH)
ROOTFS_CHECK_SIZE=$(printf '0x%x' $(($ROOTFS_CHECK_BLOCKS * $CHECK_BS)))
ROOTFS_PART_SIZE_KB=$(($MAX_PART_SIZE - $KERNEL_PART_SIZE_KB))
ROOTFS_PART_SIZE=$(printf $SIZE_FORMAT $(($ROOTFS_PART_SIZE_KB * $SIZE_FACTOR)))
cat << EOF > $CFG_OUT
[vmlinux]
filename=kernel
md5sum=$KERNEL_MD5
filemd5sum=$KERNEL_MD5
filesha256sum=$KERNEL_SHA256
flashaddr=$KERNEL_FLASH_ADDR
checksize=0x0
cmd_success=setenv bootseq 1,2; setenv kernel_size_1 $KERNEL_PART_SIZE; saveenv
cmd_fail=reset
[rootfs]
filename=rootfs
md5sum=$ROOTFS_MD5
filemd5sum=$ROOTFS_MD5_FULL
filesha256sum=$ROOTFS_SHA256_FULL
flashaddr=$ROOTFS_FLASH_ADDR
checksize=$ROOTFS_CHECK_SIZE
cmd_success=setenv bootseq 1,2; setenv kernel_size_1 $KERNEL_PART_SIZE; setenv rootfs_size_1 $ROOTFS_PART_SIZE; saveenv
cmd_fail=reset
EOF