50e3659703
Netgear DM200 is an inexpensive VDSL modem:
CPU: VRX220 MIPS 34Kc 5.6 @ 500Mhz
RAM: 64MiB
Flash: 8MiB
Ethernet: 1x100M
DSL: VDSL2+, ADSL2+
reset button, 3x bi-color LEDs
Serial port is 115200 baud, on the 4 pin header; pins from the bottom to
top are GND, RX, TX.
To upgrade from the vendor firmware, upload factory.img
The DM200 bootloader supports flashing over TFTP; hold the reset button
while powering on the device, and wait for the power light to start
flashing green before releasing. The device is now listening on
192.168.0.1/24, and can be sent a factory.img or a netgear image with a
TFTP put.
Once the image is loaded, it will be written to the flash, and the
device will reboot; this will take a few minutes.
Thanks to Edward O'Callaghan and Baptiste Jonglez, who implemented their
own ports for this device and provided valuable feedback.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
81 lines
2.1 KiB
Bash
Executable file
81 lines
2.1 KiB
Bash
Executable file
#!/bin/sh
|
|
#
|
|
# Copyright (C) 2011-2015 OpenWrt.org
|
|
# based on ar71xx
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/lantiq.sh
|
|
|
|
board_config_update
|
|
|
|
led_wifi="$(lantiq_get_dt_led wifi)"
|
|
[ -n "$led_wifi" ] && ucidef_set_led_wlan "wifi" "wifi" "$led_wifi" "phy0tpt"
|
|
|
|
led_usb="$(lantiq_get_dt_led usb)"
|
|
[ -n "$led_usb" ] && ucidef_set_led_usbdev "usb" "usb" "$led_usb" "1-1"
|
|
|
|
led_usb2="$(lantiq_get_dt_led usb2)"
|
|
[ -n "$led_usb2" ] && ucidef_set_led_usbdev "usb2" "usb2" "$led_usb2" "2-1"
|
|
|
|
led_dsl="$(lantiq_get_dt_led dsl)"
|
|
[ -n "$led_dsl" ] && {
|
|
interface="nas0"
|
|
lantiq_is_vdsl_system && interface="ptm0"
|
|
|
|
led_internet="$(lantiq_get_dt_led internet)"
|
|
if [ -n "$led_internet" ]; then
|
|
ucidef_set_led_default "dsl" "dsl" "$led_dsl" "0"
|
|
ucidef_set_led_netdev "internet" "internet" "$led_internet" "pppoe-wan"
|
|
else
|
|
ucidef_set_led_netdev "dsl" "dsl" "$led_dsl" "$interface"
|
|
fi
|
|
}
|
|
|
|
board=$(board_name)
|
|
|
|
case "$board" in
|
|
ALL0333CJ)
|
|
ucidef_set_led_netdev "lan" "lan" "all0333cj:green:lan" "eth0.1"
|
|
;;
|
|
ARV4525PW)
|
|
ucidef_set_led_netdev "wifi" "wifi" "arv4525pw:green:wlan" "wlan0"
|
|
;;
|
|
ARV7506PW11)
|
|
ucidef_set_led_wlan "wifi" "wifi" "arv7506pw11:green:wlan" "phy0radio"
|
|
;;
|
|
ARV7519RW22)
|
|
ucidef_set_led_netdev "lan" "lan" "arv7519rw22:green:lan" "eth0.1"
|
|
;;
|
|
BTHOMEHUBV5A)
|
|
ucidef_set_led_default "dimmed" "dimmed" "dimmed" "0"
|
|
;;
|
|
DM200)
|
|
ucidef_set_led_netdev "lan" "lan" "dm200:green:lan" "eth0"
|
|
;;
|
|
FRITZ7320)
|
|
ucidef_set_led_netdev "wifi" "wifi" "fritz7320:green:wlan" "wlan0"
|
|
;;
|
|
P2812HNUF*)
|
|
ucidef_set_led_wlan "wifi" "wifi" "p2812hnufx:green:wlan" "phy0radio"
|
|
;;
|
|
VGV7510KW22*)
|
|
ucidef_set_led_wlan "wifi" "wifi" "vgv7510kw22:green:wlan" "phy0radio"
|
|
;;
|
|
VGV7519*)
|
|
ucidef_set_led_wlan "wifi" "wifi" "vgv7519:green:wireless" "phy0radio"
|
|
;;
|
|
WBMR300)
|
|
ucidef_set_led_switch "lan1" "LAN1" "wbmr300:green:lan1" "switch0" "0x08"
|
|
ucidef_set_led_switch "lan2" "LAN2" "wbmr300:green:lan2" "switch0" "0x04"
|
|
ucidef_set_led_switch "wan" "WAN" "wbmr300:green:wan" "switch0" "0x10"
|
|
ucidef_set_led_switch "lan3" "LAN3" "wbmr300:green:lan3" "switch0" "0x20"
|
|
ucidef_set_led_default "router" "router" "wbmr300:green:router" "1"
|
|
;;
|
|
*)
|
|
;;
|
|
esac
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|