openwrtv4/target/linux/ramips/dts/WL-WN575A3.dts
Roger Pueyo Centelles 5f6e948551 ramips: Add support for Wavlink WL-WN575A3
This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug
wireless router with the following specifications:

 - CPU: MediaTek MT7628AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 2x 10/100 Mbps (switched)
 - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm
 - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm
 - Antennas: 4x external (2 per radio), non-detachable
 - LEDs: 4 programmable + LAN, WAN, POWER
 - Buttons: reset, WPS

Flashing instructions:

Factory U-boot launches a TFTP client if WPS button is pressed during power-on.
Rename the sysupgrade file and configure a TFTP as follows:

 - Client (WL-WN575A3) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-11-08 11:17:10 +01:00

130 lines
2.1 KiB
Text

/dts-v1/;
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include "mt7628an.dtsi"
/ {
compatible = "wavlink,wl-wn575a3", "mediatek,mt7628an-soc";
model = "Wavlink WL-WN575A3";
chosen {
bootargs = "console=ttyS0,57600";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x4000000>;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <20>;
reset {
label = "reset";
gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
gpio-leds {
compatible = "gpio-leds";
wifi-high {
label = "wl-wn575a3:green:wifi-high";
gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
};
wifi-med {
label = "wl-wn575a3:green:wifi-med";
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
};
wifi-low {
label = "wl-wn575a3:green:wifi-low";
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
};
wps {
label = "wl-wn575a3:green:wps";
gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
};
};
};
&pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "i2c", "wled_an";
ralink,function = "gpio";
};
};
};
&pcie {
status = "okay";
pcie-bridge {
mt76@0,0 {
reg = <0x0000 0 0 0 0>;
device_type = "pci";
mediatek,mtd-eeprom = <&factory 0x8000>;
mediatek,2ghz = <0>;
};
};
};
&spi0 {
status = "okay";
m25p80@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
linux,modalias = "m25p80", "en25q64";
spi-max-frequency = <10000000>;
m25p,chunked-io = <32>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "firmware";
reg = <0x50000 0x7b0000>;
};
};
};
&wmac {
status = "okay";
ralink,mtd-eeprom = <&factory 0x4>;
};
&ethernet {
mtd-mac-address = <&factory 0x2e>;
ralink,port-map = "llllw";
};