openwrtv4/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
David Bauer b6a4c67468 ar71xx: add support for Fritz!Box 4020
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.

SoC:   Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM:   Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi:  QCA9561 b/g/n 3x3 450Mbit/s
USB:   1x USB 2.0
IN:    WPS button, WiFi button
OUT:   Power LED green, Internet LED green, WLAN LED green,
       LAN LED green, INFO LED green, INFO LED red
UART:  Header Next to Black metal shield
       Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
       The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet (LAN + WAN)
 - WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Not working:
 - USB port

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-07 10:42:26 +02:00

177 lines
4 KiB
Bash

#!/bin/sh
[ -e /lib/firmware/$FIRMWARE ] && exit 0
. /lib/functions.sh
. /lib/functions/system.sh
ath9k_eeprom_die() {
echo "ath9k eeprom: " "$*"
exit 1
}
ath9k_eeprom_extract() {
local part=$1
local offset=$2
local count=$3
local mtd
mtd=$(find_mtd_chardev $part)
[ -n "$mtd" ] || \
ath9k_eeprom_die "no mtd device found for partition $part"
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
ath9k_eeprom_die "failed to extract from $mtd"
}
ath9k_ubi_eeprom_extract() {
local part=$1
local offset=$2
local count=$3
local ubidev=$(nand_find_ubi $CI_UBIPART)
local ubi
ubi=$(nand_find_volume $ubidev $part)
[ -n "$ubi" ] || \
ath9k_eeprom_die "no UBI volume found for $part"
dd if=/dev/$ubi of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
ath9k_eeprom_die "failed to extract from $ubi"
}
ath9k_eeprom_extract_reverse() {
local part=$1
local offset=$2
local count=$3
local mtd
local reversed
local caldata
mtd=$(find_mtd_chardev "$part")
reversed=$(hexdump -v -s $offset -n $count -e '/1 "%02x "' $mtd)
for byte in $reversed; do
caldata="\x${byte}${caldata}"
done
printf "%b" "$caldata" > /lib/firmware/$FIRMWARE
}
ath9k_patch_firmware_mac() {
local mac=$1
[ -z "$mac" ] && return
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=2 count=6
}
board=$(board_name)
case "$FIRMWARE" in
"soc_wmac.eeprom")
case $board in
c-55|\
c-60)
ath9k_eeprom_extract "art" 4096 2048
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary art 0) +1)
;;
fritz4020)
ath9k_eeprom_extract_reverse "urlader" 5441 1088
;;
mr18)
. /lib/upgrade/nand.sh
if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
ath9k_ubi_eeprom_extract "caldata" 4096 2048
else
ath9k_eeprom_extract "odm-caldata" 4096 2048
fi
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +1)
;;
r6100 | \
wndr3700v4 | \
wndr4300)
ath9k_eeprom_extract "caldata" 4096 2048
ath9k_patch_firmware_mac $(mtd_get_mac_binary caldata 0)
;;
rambutan)
ath9k_eeprom_extract "art" 4096 2048
;;
wlr8100)
ath9k_eeprom_extract "art" 4096 2048
ath9k_patch_firmware_mac $(mtd_get_mac_ascii u-boot-env "ethaddr")
;;
z1)
. /lib/upgrade/nand.sh
if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
ath9k_ubi_eeprom_extract "caldata" 4096 2048
else
ath9k_eeprom_extract "origcaldata" 4096 2048
fi
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +2)
;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;
esac
;;
"pci_wmac0.eeprom")
case $board in
c-55)
ath9k_eeprom_extract "art" 20480 2048
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary art 0) +2)
;;
fritz300e)
ath9k_eeprom_extract_reverse "urloader" 5441 1088
;;
mr18)
. /lib/upgrade/nand.sh
if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
ath9k_ubi_eeprom_extract "caldata" 20480 2048
else
ath9k_eeprom_extract "odm-caldata" 20480 2048
fi
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +2)
;;
wndr3700v4 | \
wndr4300)
ath9k_eeprom_extract "caldata" 20480 2048
ath9k_patch_firmware_mac $(mtd_get_mac_binary caldata 12)
;;
z1)
. /lib/upgrade/nand.sh
if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
ath9k_ubi_eeprom_extract "caldata" 86016 4096
else
ath9k_eeprom_extract "origcaldata" 86016 4096
fi
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +3)
;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;
esac
;;
"pci_wmac1.eeprom")
case $board in
mr18)
. /lib/upgrade/nand.sh
if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
ath9k_ubi_eeprom_extract "caldata" 36864 2048
else
ath9k_eeprom_extract "odm-caldata" 36864 2048
fi
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +3)
;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;
esac
;;
esac