No description
Find a file
Thomas Reifferscheid 17f60b1cd2 ipq8064: fix dwc3-of-simple module unloading
Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:

root@LEDE:/# rmmod dwc3-of-simple
[   21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   21.391931] usb usb4: USB disconnect, device number 1
[   21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   21.406685] usb usb3: USB disconnect, device number 1
[   21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.

Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.

At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.

root@LEDE:/# rmmod dwc3
[   53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   53.827412] usb usb4: USB disconnect, device number 1
[   53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   53.842314] usb usb3: USB disconnect, device number 1
[   53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   53.857882] usb usb2: USB disconnect, device number 1
[   53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[   53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   53.873696] usb usb1: USB disconnect, device number 1
[   53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#

For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0

The patch however addresses the clock assignment from the .dtsi
file. Most probably it went into openwrt here:
https://dev.openwrt.org/browser/trunk/target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch?rev=45261
copied from Qualcomms attempt here: https://lkml.org/lkml/2015/11/20/116

Now unloading and repeated module loading is working just fine,
no matter if you'd remove dwc3-of-simple or dwc3.

root@LEDE:/# rmmod dwc3-of-simple
[   24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   24.089765] usb usb4: USB disconnect, device number 1
[   24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   24.104522] usb usb3: USB disconnect, device number 1
[   24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   24.120396] usb usb2: USB disconnect, device number 1
[   24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[   24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   24.135948] usb usb1: USB disconnect, device number 1
[   24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#

Fixes: dwc3-of-simple module unloading

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-03-28 09:03:55 +02:00
.github github: include pull request template 2017-03-12 17:38:31 +01:00
config build: add devel option to store build config in firmware 2017-03-18 12:08:04 +01:00
include kernel: update kernel 4.9 to 4.9.17 2017-03-26 12:23:19 +02:00
package mac80211: ath10k: allow failure getting board id via otp 2017-03-28 08:50:18 +02:00
scripts scripts: only generate config from feature flag if fully match 2017-03-20 22:04:41 +01:00
target ipq8064: fix dwc3-of-simple module unloading 2017-03-28 09:03:55 +02:00
toolchain toolchain/binutils: Add binutils 2.28 2017-03-20 08:23:58 +01:00
tools tools/upx: Remove from repo 2017-03-20 08:26:35 +01:00
.gitattributes add .gitattributes to prevent the git autocrlf option from messing with CRLF/LF in files 2012-05-08 13:30:49 +00:00
.gitignore gitignore: add /overlay 2017-01-15 18:16:29 +01:00
BSDmakefile add missing copyright header 2007-02-26 01:05:09 +00:00
Config.in branding: add LEDE branding 2016-03-24 22:40:13 +01:00
feeds.conf.default Add video feed to feeds.conf.default 2017-01-25 16:04:39 +01:00
LICENSE finally move buildroot-ng to trunk 2016-03-20 17:29:15 +01:00
Makefile build: prepare config.seed before package compilation 2017-03-18 12:08:04 +01:00
README README: Update project README 2016-05-12 03:29:36 +02:00
rules.mk rules.mk: make PKG_CONFIG_DEPENDS properly track string values 2017-02-27 23:46:53 +01:00

This is the buildsystem for the LEDE Linux distribution.

Please use "make menuconfig" to choose your preferred
configuration for the toolchain and firmware.

You need to have installed gcc, binutils, bzip2, flex, python, perl, make,
find, grep, diff, unzip, gawk, getopt, subversion, libz-dev and libc headers.

Run "./scripts/feeds update -a" to get all the latest package definitions
defined in feeds.conf / feeds.conf.default respectively
and "./scripts/feeds install -a" to install symlinks of all of them into
package/feeds/.

Use "make menuconfig" to configure your image.

Simply running "make" will build your firmware.
It will download all sources, build the cross-compile toolchain, 
the kernel and all choosen applications.

To build your own firmware you need to have access to a Linux, BSD or MacOSX system
(case-sensitive filesystem required). Cygwin will not be supported because of
the lack of case sensitiveness in the file system.


Sunshine!
	Your LEDE Community
	http://www.lede-project.org