openwrtv4/target/linux/ath79/dts/ar9331_pisen_wmm003n.dts
Dmitry Tunin 7a873974f7 ath79: add support for indicating the boot state using multiple leds
Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which
supports different leds for the different boot states.

The existing led sequences should be the same as before.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[reword commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-15 07:42:36 +02:00

127 lines
2 KiB
Text

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar9331.dtsi"
/ {
model = "Pisen WMM003N";
compatible = "pisen,wmm003n", "qca,ar9331";
aliases {
serial0 = &uart;
led-boot = &led_system;
led-failsafe = &led_system;
led-running = &led_system;
led-upgrade = &led_system;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
poll-interval = <20>;
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
gpio-leds {
compatible = "gpio-leds";
led_system: system {
label = "pisen:blue:system";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
};
};
reg_usb_vbus: reg_usb_vbus {
compatible = "regulator-fixed";
regulator-name = "usb_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot: partition@0 {
reg = <0x0 0x20000>;
label = "u-boot";
read-only;
};
firmware: partition@20000 {
reg = <0x20000 0x7d0000>;
label = "firmware";
};
art: partition@7f0000 {
reg = <0x7f0000 0x10000>;
label = "art";
read-only;
};
};
};
};
&eth0 {
status = "okay";
mtd-mac-address = <&uboot 0x1fc00>;
gmac-config {
device = <&gmac>;
switch-phy-addr-swap = <0>;
switch-phy-swap = <0>;
};
};
&eth1 {
status = "okay";
compatible = "syscon", "simple-mfd";
};
&gpio {
status = "okay";
};
&uart {
status = "okay";
};
&usb {
dr_mode = "host";
vbus-supply = <&reg_usb_vbus>;
status = "okay";
};
&usb_phy {
status = "okay";
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&uboot 0x1fc00>;
};