#include "qcom-ipq8064-v1.0.dtsi" #include <dt-bindings/input/input.h> / { model = "TP-Link Archer C2600"; compatible = "tplink,c2600", "qcom,ipq8064"; memory@0 { reg = <0x42000000 0x1e000000>; device_type = "memory"; }; reserved-memory { #address-cells = <1>; #size-cells = <1>; ranges; rsvd@41200000 { reg = <0x41200000 0x300000>; no-map; }; }; aliases { serial0 = &gsbi4_serial; mdio-gpio0 = &mdio0; led-boot = &power; led-failsafe = &general; led-running = &power; led-upgrade = &general; }; chosen { linux,stdout-path = "serial0:115200n8"; }; soc { pinmux@800000 { button_pins: button_pins { mux { pins = "gpio16", "gpio54", "gpio65"; function = "gpio"; drive-strength = <2>; bias-pull-up; }; }; i2c4_pins: i2c4_pinmux { mux { pins = "gpio12", "gpio13"; function = "gsbi4"; drive-strength = <12>; bias-disable; }; }; led_pins: led_pins { mux { pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33", "gpio53", "gpio66"; function = "gpio"; drive-strength = <2>; bias-pull-up; }; }; spi_pins: spi_pins { mux { pins = "gpio18", "gpio19", "gpio21"; function = "gsbi5"; bias-pull-down; }; data { pins = "gpio18", "gpio19"; drive-strength = <10>; }; cs { pins = "gpio20"; function = "gpio"; drive-strength = <10>; bias-pull-up; }; clk { pins = "gpio21"; drive-strength = <12>; }; }; mdio0_pins: mdio0_pins { mux { pins = "gpio0", "gpio1"; function = "gpio"; drive-strength = <8>; bias-disable; }; }; rgmii2_pins: rgmii2_pins { mux { pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; function = "rgmii2"; drive-strength = <8>; bias-disable; }; }; usb0_pwr_en_pin: usb0_pwr_en_pin { mux { pins = "gpio25"; function = "gpio"; drive-strength = <10>; bias-pull-up; output-high; }; }; usb1_pwr_en_pin: usb1_pwr_en_pin { mux { pins = "gpio23"; function = "gpio"; drive-strength = <10>; bias-pull-up; output-high; }; }; }; gsbi@16300000 { qcom,mode = <GSBI_PROT_I2C_UART>; status = "ok"; serial@16340000 { status = "ok"; }; /* * The i2c device on gsbi4 should not be enabled. * On ipq806x designs gsbi4 i2c is meant for exclusive * RPM usage. Turning this on in kernel manifests as * i2c failure for the RPM. */ }; gsbi5: gsbi@1a200000 { qcom,mode = <GSBI_PROT_SPI>; status = "ok"; spi5: spi@1a280000 { status = "ok"; pinctrl-0 = <&spi_pins>; pinctrl-names = "default"; cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; flash: m25p80@0 { compatible = "jedec,spi-nor"; #address-cells = <1>; #size-cells = <1>; spi-max-frequency = <50000000>; reg = <0>; SBL1@0 { label = "SBL1"; reg = <0x0 0x20000>; read-only; }; MIBIB@20000 { label = "MIBIB"; reg = <0x20000 0x20000>; read-only; }; SBL2@40000 { label = "SBL2"; reg = <0x40000 0x20000>; read-only; }; SBL3@60000 { label = "SBL3"; reg = <0x60000 0x30000>; read-only; }; DDRCONFIG@90000 { label = "DDRCONFIG"; reg = <0x90000 0x10000>; read-only; }; SSD@a0000 { label = "SSD"; reg = <0xa0000 0x10000>; read-only; }; TZ@b0000 { label = "TZ"; reg = <0xb0000 0x30000>; read-only; }; RPM@e0000 { label = "RPM"; reg = <0xe0000 0x20000>; read-only; }; fs-uboot@100000 { label = "fs-uboot"; reg = <0x100000 0x70000>; read-only; }; uboot-env@170000 { label = "uboot-env"; reg = <0x170000 0x40000>; read-only; }; radio@1b0000 { label = "radio"; reg = <0x1b0000 0x40000>; read-only; }; os-image@1f0000 { label = "os-image"; reg = <0x1f0000 0x200000>; }; rootfs@3f0000 { label = "rootfs"; reg = <0x3f0000 0x1b00000>; }; defaultmac: default-mac@1ef0000 { label = "default-mac"; reg = <0x1ef0000 0x00200>; read-only; }; pin@1ef0200 { label = "pin"; reg = <0x1ef0200 0x00200>; read-only; }; product-info@1ef0400 { label = "product-info"; reg = <0x1ef0400 0x0fc00>; read-only; }; partition-table@1f00000 { label = "partition-table"; reg = <0x1f00000 0x10000>; read-only; }; soft-version@1f10000 { label = "soft-version"; reg = <0x1f10000 0x10000>; read-only; }; support-list@1f20000 { label = "support-list"; reg = <0x1f20000 0x10000>; read-only; }; profile@1f30000 { label = "profile"; reg = <0x1f30000 0x10000>; read-only; }; default-config@1f40000 { label = "default-config"; reg = <0x1f40000 0x10000>; read-only; }; user-config@1f50000 { label = "user-config"; reg = <0x1f50000 0x40000>; read-only; }; qos-db@1f90000 { label = "qos-db"; reg = <0x1f90000 0x40000>; read-only; }; usb-config@1fd0000 { label = "usb-config"; reg = <0x1fd0000 0x10000>; read-only; }; log@1fe0000 { label = "log"; reg = <0x1fe0000 0x20000>; read-only; }; }; }; }; phy@100f8800 { /* USB3 port 1 HS phy */ status = "ok"; }; phy@100f8830 { /* USB3 port 1 SS phy */ status = "ok"; }; phy@110f8800 { /* USB3 port 0 HS phy */ status = "ok"; }; phy@110f8830 { /* USB3 port 0 SS phy */ status = "ok"; }; usb30@0 { status = "ok"; pinctrl-0 = <&usb0_pwr_en_pin>; pinctrl-names = "default"; }; usb30@1 { status = "ok"; pinctrl-0 = <&usb1_pwr_en_pin>; pinctrl-names = "default"; }; pcie0: pci@1b500000 { status = "ok"; phy-tx0-term-offset = <7>; }; pcie1: pci@1b700000 { status = "ok"; phy-tx0-term-offset = <7>; }; mdio0: mdio { compatible = "virtual,mdio-gpio"; #address-cells = <1>; #size-cells = <0>; gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; pinctrl-0 = <&mdio0_pins>; pinctrl-names = "default"; phy0: ethernet-phy@0 { device_type = "ethernet-phy"; reg = <0>; qca,ar8327-initvals = < 0x00004 0x7600000 /* PAD0_MODE */ 0x00008 0x1000000 /* PAD5_MODE */ 0x0000c 0x80 /* PAD6_MODE */ 0x000e4 0x6a545 /* MAC_POWER_SEL */ 0x000e0 0xc74164de /* SGMII_CTRL */ 0x0007c 0x4e /* PORT0_STATUS */ 0x00094 0x4e /* PORT6_STATUS */ >; }; phy4: ethernet-phy@4 { device_type = "ethernet-phy"; reg = <4>; }; }; gmac1: ethernet@37200000 { status = "ok"; phy-mode = "rgmii"; qcom,id = <1>; pinctrl-0 = <&rgmii2_pins>; pinctrl-names = "default"; mtd-mac-address = <&defaultmac 0x8>; mtd-mac-address-increment = <1>; fixed-link { speed = <1000>; full-duplex; }; }; gmac2: ethernet@37400000 { status = "ok"; phy-mode = "sgmii"; qcom,id = <2>; mtd-mac-address = <&defaultmac 0x8>; fixed-link { speed = <1000>; full-duplex; }; }; rpm@108000 { pinctrl-0 = <&i2c4_pins>; pinctrl-names = "default"; }; }; gpio-keys { compatible = "gpio-keys"; pinctrl-0 = <&button_pins>; pinctrl-names = "default"; wifi { label = "wifi"; gpios = <&qcom_pinmux 49 GPIO_ACTIVE_LOW>; linux,code = <KEY_RFKILL>; }; reset { label = "reset"; gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; linux,code = <KEY_RESTART>; }; wps { label = "wps"; gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; linux,code = <KEY_WPS_BUTTON>; }; ledswitch { label = "ledswitch"; gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; linux,code = <KEY_LIGHTS_TOGGLE>; }; }; gpio-leds { compatible = "gpio-leds"; pinctrl-0 = <&led_pins>; pinctrl-names = "default"; lan { label = "c2600:white:lan"; gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>; }; usb4 { label = "c2600:white:usb_4"; gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; }; usb2 { label = "c2600:white:usb_2"; gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; }; wps { label = "c2600:white:wps"; gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; }; wan_amber { label = "c2600:amber:wan"; gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>; }; wan_white { label = "c2600:white:wan"; gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>; }; power: power { label = "c2600:white:power"; gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; default-state = "keep"; }; general: general { label = "c2600:white:general"; gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; }; }; }; &adm_dma { status = "ok"; };