The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.
This makes OpenWrt always use vlan1 and vlan2 instead.
SVN-Revision: 35704
This contains the following new bigger changes:
* new partition parser which still could lake some features or have bugs
* new nand flash driver
* using physmap-flash flash driver for parallel flash
* some changes to the serial flash driver
With these changes OpenWrt starts using more of the mainline flash drivers.
SVN-Revision: 35632
Adjust the "AutoLoad" number for the BGMAC module to be prior
to the switch modules. This probably isn't real important as
the modules are loaded in the correct order by preinit anyway.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35625
The included patch will generate a correct network configuration on the simpletech simpleshare.
Thank you for the patch Will Holmes (RealOpty)
This closes#12361.
SVN-Revision: 35623
The mac address should be aligned to u16 to prevent an unaligned access
in drivers/ssb/pci.c where it is casted to __be16.
This closes#9824.
SVN-Revision: 35618
This also removes kmod-ocf, because kmod-crypto-ocf is automatically selected by kmod-ocf-ubsec-ssb.
Thank you Manuel Munz <freifunk@somakoma.de> for the patch.
SVN-Revision: 35509
Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2
in /lib/preinit/05_init_interfaces_brcm. The list of devices will need to
be expanded. Is there a way to determine the correct cpu_port to use in a
generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if
"/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists? Could
a similar method be used in "/etc/init.d/netconfig"?
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35491
The default profile now contains Ethernet drivers for all the types
found on supported boards. There are other profiles for each Ethernet
driver.
SVN-Revision: 35314
Update the default IRQ assignment for unrecognized devices per
the upstream change.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35121
1) Fix what appears to be a logic error in bgmac_phy_advertise.
2) Fix bgmac_ioctl to use passed phy_id; needed for switch-robo
interface w/ the driver to work correctly. I still have the issue
with the interface always being HD when the speed/duplex is set
manually (e.g., echo "100FD" > /proc/switch/eth0/port/N/media).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35052
This Ethernet driver is in early development stage and still has some problems.
This was working on my bcm4716 based device.
Thanks to Rafał Miłecki <zajec5@gmail.com> for writing this driver.
SVN-Revision: 34995
Adjust the IRQ Flag value from 8 to 7 for I2S Core for BCM4716 and
BCM4748 (per the Broadcom SDK). IRQ Flag values greater than 7 are
ignored when setting the interrupt masks.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34990
The behaviour of calling 'mount' differed depending on whether it called
the busybox-mount, the mount of util-linux, the mount defined in
/lib/functions.sh and /lib/functions/boot.sh
/etc/preinit even included /lib/functions.sh and /lib/functions/boot.sh,
both re-defining 'mount'.
SVN-Revision: 34792
I noticed these changes when reviewing the 2011 Broadcom SDK. I haven't
noticed any obvious changes in behavior with them applied; but thought I
should at least pass them on.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34670
The irq signal numbers that are send by the cpu are increased by 2 from
the number programmed into the mips core by bcma.
Return the irq number on which the irqs are send in bcma_core_irq() now.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34669
These patches are not specific to bcm47xx and will be used on other
platforms as well.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 34501
