* build for pentium4 instead of i486
* enable PAE
* enable EFI support
* enable KVM guest and host support
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the DMI data available in sysfs to extract manufacturer and model info
and write it to /tmp/sysinfo/.
The data will be picked up by board_detect and can be used by e.g. LuCI to
display a more appropriate model description.
On an APU board the files will contain the following values:
# cat /tmp/sysinfo/model
PC Engines APU
# cat /tmp/sysinfo/board_name
pc-engines-apu
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Enable support for DMI decoding in the kernel so that we can access
manufacturer and model information via sysfs.
Also remove redundant per-subtarget DMI overrides and preset a few
previously unset symbols popping up due to the now enabled DMI support.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
most symbols should be in Kernel packages
depending on HW the removal of
CONFIG_REALTEK_PHY
and USB symbols might be wrong
compile tested only
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Initially for ARC we were building vmlinux images because it
was both simpler and more convenient to debug Linux kernel
in runt-time via JTAG. Now when base system works quite nice
we may finally use U-Boot for loading the system image as
well. Still we keep building vmlinux images as some of our
boards are development boards and loading images with JTAG
could be at some points very beneficial.
Note for U-Boot header it's required to specify 2 values:
* loading address
* entry point (if it doesn't match loading address)
and in case of ARC entry point (EP) not only differs from
loading address but also changes from build to build due to
initramfs being placed between loading address and text section.
To accommodate that feature we have to calculate EP after
vmlinux gets built and before call to mkimage.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
even it's a little bit verbose, unmacrod board descriptions are much
easier to read and to understand.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This patch adds support for the Netgear EVG2000 VoIP Gateway to the
bcm63xx targets.
This device was not sold to the general public, but rather is/was
provided by telcos to customers in Sweden, Australia, Singapore and
other parts of asia.
Known issues:
- Unable to detect 53115 switch. This appear to be a problem with
probing for the PHY using MDIO and results in error 5. Doesn't seem to
be a problem with the configuration, and could use someone with
experience to have a look at it.
- Uses the b43 driver as using the OpenWRT/LEDE broadcom-wl driver
fails to load the firmware for the 4322, so 802.11n is not supported.
More info on the device and the research can be found at:
https://wiki.openwrt.org/toh/netgear/evg2000https://wikidevi.com/wiki/Netgear_EVG2000https://github.com/Xotic750/mirror-lede/tree/evg2000https://forum.openwrt.org/viewtopic.php?id=63950
Signed-off-by: Graham Fairweather <xotic750@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Some devices with ath9k WiFi require changing the default active low
polarity to high in order to correctly operate the WiFi status LEDs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These scripts were causing ip issues in the latest version of LEDE:
https://gist.github.com/Noltari/6d20d8bcbe236caf516c0a73f5477d00
Fixes preinit iface script by making eth0 the default ifname and only changing
it to eth1 for the devices that specifically need it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620.
- Allow up to 3 uarts on MT7621 and MT7628.
- Remove unneeded SERIAL_8250_RT288X for MT7628.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.
Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The previous image creation code would have failed if the
unpadded kernel uImage size was less than 64 bytes from the
next erase block boundary. Fix that.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
