This patch adds support for the TP-Link TL-WR802N Version 2.
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of FLash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)
Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to http://192.168.0.1 (default user is "admin" & password is "admin)
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware "*.factory-us.bin" or "*.factory-eu.bin" for eu model
- Click upgrade
Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
Serial Configuration 115200 8n1
- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
(IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
(e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
(e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
(e.g bootm 0x9f020000)
Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO
Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery
Tested on:
- Lima development kit
Signed-off-by: Karol Dudek <karoiz@sli.pl>
This patch adds support for the MikroTik RouterBOARD hEX lite
https://routerboard.com/RB750r2
Specifications:
- SoC: Qualcomm QCA9531 (850MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in)
This ethernet router is based on the same platform as the hEX PoE lite (it
shares the same board identifier), but has no USB and no PoE out.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the MikroTik RouterBOARD hEX PoE lite
https://routerboard.com/RB750UPr2
Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A
This ethernet router is based on the same platform as the wireless router hAP.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD
Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M
This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.
Available FLASH space, with LEDE trunk, is only 240 KB.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
platform_find_rootfspart() fails if the kernel partition comes before the
rootfs partition. The proposed patch fixes this while preserving what I
understand was the original idea: stop at first match.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB
TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")
Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support Abicom International Scorpion SC450 Board
QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB NAND Flash
16MB NOR Flash
10/100/1000 Ethernet
15W Max, 3x3 Mode, Full Power TX Power
802.3-at POE+ & DC Input options
100x 85mm
USB
PCIe
SFP
GPIO/LED
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Support Abicom International Scorpion SC300M Module
QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB SPI Flash
802.11a/na/b/g/ng
GPIO x 22, USB x2, PCIe x2
10/100/1000 Ethernet
23dBm, Optional Onboard Antenna
DC Input, 8-20V DC
85 x 55 mm
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Add full support for Mikrotik RB-941-2nD (hAP lite)
Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.
There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.
The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)
The result factory image is flashable from the stock web ui.
Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This also makes the detection more flexible, as it doesn't need to check
for each model explicitly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.
YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.
Common specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm
SR3200 specification:
- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB
XD3200 specification:
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB
LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.
Flash instruction under vendor firmware, using telnet/SSH:
1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Remove all comments in ubnt_xm_board_detect(), as it's not possible to add
comments to specific lines of the case construct anyways.
Fixes: 9a5801e7 "ar71xx: add model detection for UBNT Rocket Ti"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.
Use the same flash approach as for YunCore AP90Q.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Flash instruction under vendor fimrware, using telnet/SSH:
1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.
There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size
Version number is available only inside vendor GUI,
hardware and markings are the same.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.
All 3 devices are based on Qualcomm/Atheros QCA9531 v2.
COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.
Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
This patch adds support for the Airtight C-60.
SOC: Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM: 128 MiB
NOR: MX25L3205D 4MiB
NAND: ST Micro NAND 32MiB 3,3V 8-bit
SW-NET: AR8327N (2 Ports)
WLAN1: Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2: Dual-Band AR9300 Rev:4 PCIe Chip
The switch is setup for an accesspoint:
LAN1: (gigabit) is the wan-port.
LAN2: (fast ethernet) is bridged with the br-lan.
Flashing Guide (via initramfs):
1. Connect a PC to the serial port of the C-60.
power up the C-60.
Enter u-boot command prompt:
#> nand erase
#> setenv bootcmd "bootm 0x9f060000"
#> saveenv
#> setenv ipaddr 192.168.1.1
#> setenv netmask 255.255.255.0
#> setenv serverip 192.168.1.100
#> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
#> tftpboot
#> bootm
2. Wait for the C-60 to boot LEDE.
On the root prompt. Enter:
# ubiformat /dev/mtd4
# ubiattach -p /dev/mtd4
3. After that copy the sysupgrade.tar onto the router and run:
# sysupgrade sysupgrade.tar
to flash the image.
Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ar71xx has an init-script for special devices where the ath10k OTP
calibration data is stored on the PCIe card's EEPROM (and thus can only
be read by ath10k). Unfortunately the OTP data uses the default mac
address (= all devices come with the same mac address, which leads to
problems when you have multiple of these devices in the same network).
To work around this the mac address is patched in the firmware during
the first boot of the device. To prevent flash wear this was only done
if the ath10k firmware matched a hardcoded md5sum.
However, if the md5sum does not match this can mean that either the mac
address was already patched (which is fine) - unfortunately it can also
mean that the firmware version was updated without updating the
hardcoded md5sum.
Change the "was the mac address already patched" check to actually
compare the mac address inside the ath10k firmware.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- two external, non-detachable antennas
- 8x LED, 1x button
- UART header (pinout: VCC, RX, TX, GND)
Flash instruction:
Use sysupgrade in vendor firmare which is based on OpenWrt.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The mw4530r-v1 profile in tp-link.mk is for Mercury MW4530R.
There is no such a device called TL-WDR4530.
Also change MERCURY to Mercury in /lib/ar71xx.sh
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers
Default configuration:
- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space
Flash instruction (do it under U-Boot, using RS232):
1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers
Default configuration:
- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.
Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
The CE image format used by OpenMesh can contain extra blocks which
are not used for flashing. Only the first three embedded images
(fwupgrade.cfg, kernel, rootfs) are required in this order to successfully
flash an image via sysupgrade. All extra embedded images should be ignored
for the available devices.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The platform_check_image_openmesh function used break statements to signal
that the board name matched the image target. This worked because the
sysupgrade binary checked the image inside a loop. The break statement
stopped the loop and skipped any additional check.
Instead the check should be done without such sideeffects by simply
combining the board names and image targets. Only a mismatch should cause a
negative result for the caller and skipping of the additional checks.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
- CPU QCA9531-BL3A
- RAM: 64MB
- flash: 16MB
- USB
AP143 platform, similar to tl-wr841n v10/v11, but with USB
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.
Signed-off-by: P.Wassi <p.wassi at gmx.at>
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 49157
Let's not confuse users about the revisions of their devices when we can
easily avoid it.
Not tested on real hardware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49107
Instead of adding the space when combining $model and $hwver, add the space
to the beginning of $hwver, so the resulting string won't end with a space
when $hwver is set to the empty string.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49106
There's no reason for us to be more lenient than the stock firmware, so
better check the HWREV as well to avoid bricked devices.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49105
My last bugfix (r47538) introduced a new bug in wndr3700_board_detect
(again...).
Assigning the result of ar71xx_get_mtd_offset_size_format to the model
variable before stripping of garbage using awk will cause all NUL bytes to
be removed before awk is applied, leading to model strings like
"NETGEAR WNDRMACv2NETGEAR", where a NUL byte after the v2 is supposed to
terminate the string.
Fix by calling ar71xx_get_mtd_offset_size_format twice, once piping to awk
directly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 48075
This patch adds support for the Bitmain Antrouter R1
http://wiki.openwrt.org/toh/bitmain/r1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 48058
