This causes problem when a FQDN is configured in /etc/config/system. The
domain name will appear twice in reverse DNS.
Next to that, there seems to be a bug in dnsmasq. From the manual page:
--interface-name=<name>,<interface>[/4|/6]
Return a DNS record associating the name with the primary address
on the given interface. This flag specifies an A or AAAA record for the
given name in the same way as an /etc/hosts line, except that the address
is not constant, but taken from the given interface. The interface may be
followed by "/4" or "/6" to specify that only IPv4 or IPv6 addresses
of the interface should be used. If the interface is down, not configured
or non-existent, an empty record is returned. The matching PTR record is
also created, mapping the interface address to the name. More than one name
may be associated with an interface address by repeating the flag; in that
case the first instance is used for the reverse address-to-name mapping.
It does not just create an A/AAAA record for the primary address, it creates
one for all addresses. And what is worse, it seems to actually resolve to the
non-primary address first. This is quite annoying when you use floating IP
addresses (e.g. VRRP), because when the floating IP is on the other device,
SSH failes due to incorrect entry in the known hosts file.
I know that this is not a common setup, but it would be nice if there was an
option to restore the previous behaviour, rather than just forcing this new
feature on everybody.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
'add_local_hostname' previous implementation may drop some addresses.
Soft addition of IP6 addresses may not cause a reload or restart event.
dnsmasq '--interface-name' robustly applies DNS to all addresses per
interface (except fe80::/10).
Change UCI 'add_local_hostname' to expand during each interface assignement
during add_dhcp().
Assign '<iface>.<host>.<domain>' as true name (reflexive A, AAAA, and PTR).
Assign '<host>.<domain>' and '<host>' as convinience aliases (no PTR, not
technically CNAME).
This is accomplished with the '--interface-name' order, first is PTR.
We could also assign each <ip4/6>.<iface>.<host>.<domain> to the respective
dual stack on the interface.
That seemed excessive so it was skipped (/4 or /6 suffix to the interface).
Add UCI 'add_wan_hostname' similar to 'add_local_hostname' function for
external WAN.
WAN IP4 are less often named by the ISP and rarely WAN IP6 due to complexity.
For logs, LuCI connection graph, and other uses assigning a WAN name is desired.
'add_local_hostname' only applies with DHCP and 'add_wam_hostname' only applies
without DHCP. Common residential users will want to set both options TRUE.
Businesses will probably have global DNS, static IP, and 'add_wan_hostname' FALSE.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
Add DHCPv6 matching by DHCP Unique Identifier (RFC-3315) in addition to
existing MAC-address (RFC-6939). The latter is not widely supported yet.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
add possibility to set the facility to which dnsmasq will send syslog entries, i.e. set it to '/dev/null' to mute dnsmasq output at all.
Signed-off-by: Dirk Brenken dev@brenken.org
The SIGHUP also got sent to the reload script making it bail out
with an error
Revert "dnsmasq: reload config if host name is modified"
This reverts commit 854459a2f9.
Reported-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Let dnsmasq read all hosts files in /tmp/hosts directory by specifying
/tmp/hosts as argument of --addn-host
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Correct splitting the 32-bit 'hostid' value to two 16-bit hexadecimal
values. Previously, the lower 16-bit value was truncated to an 8-bit
value, which would result in hostid values 100 and 200 both to be set
to [::0:0] instead of [::0:100] and [::0:200] respectively.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
If the hostname in /etc/config/system is modified the dnsmasq will not
reread the update host file under /tmp/hosts/dhcp.$cfg.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Adds the mac address of the DNS requestor to DNS queries which
are forwarded upstream and can be used to do filtering by the
upstream servers. This only works if the requestor is on the
same subnet as the dnsmasq server
The addmac parameter can hold the following values:
0 : mac address is not added
1 : mac address is added in binary format
base64 : mac address is added base64 encoded
text: : mac address is added in human readable format
as hex and colons
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Adds support in uci for configuring multiple dnsmasq instances via
multiple dnsmasq sections.
The uci sections host, boot, mac, tag, vendorclass, userclass,
circuitid, ... will refer to a dnsmasq instance via the instance
parameter defined in the section; if the instance parameter is
not specified backwards compatibility is preserved.
Start/Stopping a dnsmasq instance can be achieved by passing the
dnsmasq instance name as argument to start/stop via the init script.
Multiple dnsmasq instances is usefull in scenarios where you want to
bind a dnsmasq instance to an interface in order to isolate networks.
This patch is a rework of a multiple dnsmasq instance patch by Daniel Dickinson
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Match sections allow to set a tag specified by the option networkid if the client
sends an option and optionally the option value specified by the match option.
The force option will convert the dhcp-option to force-dhcp-option if set to 1 in
the dnsmasq config if options are specified in the dhcp_option option.
config match
option networkid tag
option match 12,myhost
option force 1
list dhcp_option '3,192.168.1.1'
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Regression introduced by 3481d0d dnsmasq: run as dedicated UID/GID
dnsmasq is unable to remove its own pidfile as /var/run/dnsmasq is owned
by root and now dnsmasq runs as dnsmasq:dnsmasq. Change directory
ownership to match.
dnsmasq initially starts as root, creates the pidfile, then drops to
requested non-root user. Until this fix dnsmasq had insufficient
privilege to remove its own pidfile.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
multiple invocation of dnsmasq script (e.g. by procd and hotplugd)
might cause procd to restart dnsmasq with an incomplete config file.
Config file generation might take quite a long time on larger configs
due ubus calls for each listening interface...
Signed-off-by: Ulrich Weber <ulrich.weber@riverbed.com>
Change dnsmasq's dnssec time check handling to use time validity
indicated by ntpd rather than maintaining a cross boot/upgrade
/etc/dnsmasq.time timestamp file. This saves flash device wear.
If ntpd client is configured in uci and you're using dnssec, then
dnsmasq will not check dnssec timestamp validity until ntpd hotplug
indicates sync via a stratum change. The ntpd hotplug leaves a status
flag file to indicate to dnsmasq.init that time is valid and that it
should now start in 'check dnssec timestamp valid' mode.
If ntpd client is not configured and you're using dnssec, then it is
presumed you're using an alternate time sync mechanism and that time is
correct, thus dnsmasq checks dnssec timestamps are valid from 1st start.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
V2 - stratum & step ntp changes indicate time is valid
V3 - on initial flag file step signal dnsmasq with SIGHUP if running
V4 - only accept step ntp changes. Accepting both stratum & step could
result in unpleasant script race conditions
V5 - Actually only accepting stratum is the correct thing to do after
further testing
V6 - improve handling of non busybox ntpd
if sysntpd not executable
dnsmasq checks dnssec timestamps
else
sysntp script disabled - look for timestamp file - allows external mechanism to use hotplug flag file
sysntp script enabled & uci ntp enabled - look for timestamp file
sysntp script enabled & uci ntp disabled - dnsmasq checks dnssec
timestamps
fi
Add support for hostid dhcp config entry to dnsmasq. This allows
specification of dhcpv6 hostid suffix and works in the same way as
odhcpd.
Entries in auto generated dnsmasq.conf should conform to:
dhcp-host=mm:mm:mm:mm:mm:mm,IPv4addr,[::V6su:ffix],hostname
example based on sample config/dhcp entry:
config host
option name 'Kermit'
option mac 'E0:3F:49:A1:D4:AA'
option ip '192.168.235.4'
option hostid '4'
dhcp-host=E0:3F:49:A1:D4:AA,192.168.235.4,[::0:4],Kermit
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
By default dnsmasq uses random ports for outbound dns queries;
when the maxport UCI option is specified the ports used will
always be smaller than the specified value.
This is usefull for systems behind firewalls.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Instead of making assumptions about the leasefile and resolv file make sure
we use what the user configures, but fall back to defaults if no configuration
is specified
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
Running dnsmasq in a dedicated user/group allows matching its outgoing
traffic more easily using iptables' owner match.
Add UID/GID to the package metadata and append the user/group
parameters to the init script.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 49252
Parameter allows to enable/disable static leases; by default the value is 1
to keep backwards compatibility
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49187
Enable setting a host-specific lease time for static hosts.
The new option is called "leasetime" and the format is similar
as for the default lease time: e.g. 12h, 3d, infinite
Default lease time is used for all hosts for which there is
no host-specific definition.
The option is added to /etc/config/dhcp for the selected hosts:
config host
option name 'Nexus'
option mac 'd8:50:66:55:59:7c'
option ip '192.168.1.245'
option leasetime '2h'
It gets appended to /var/etc/dnsmasq.conf like this:
dhcp-host=d8:50:66:55:59:7c,192.168.1.245,Nexus,2h
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 48801
Commit 6a7e56b adds support for adding local hostname for own lan ula adress
but if ula prefix is not specified results into an invalid config (address=/OpenWrt.lan/1)
causing dnsmasq not to start up.
Use lanaddr6 when adding local hostname as the lan ula address is constructed based on the
UCI parameters ip6hint and ip6ifaceid and thus not always ula prefix suffixed with 1
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 48495
By default dnsmasq uses random ports for outbound dns queries;
when the minport UCI option is specified the ports used will
always be larger than the specified value.
This is usefull for systems behind firewalls.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 48244
By default dnsmasq sends an ICMP echo request before allocating
an IP address to a host; the uci option noping allows to disable
this check.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 47974
Changed option nonwildcard from --bind-interfaces into --bind-dynamic.
With this, Dnsmasq binds the address of individual interfaces, allowing multiple
dnsmasq instances, but if new interfaces or addresses appear, it automatically
listens on those. This makes dynamically created interfaces work in the same way as
the default, but allows also use of other DNS-servers (like Named) at the same time
on diffirent interfaces where Dnsmasq is NOT configured, whereas with
--bind-interfaces will still reserve every interface even if not used and thus
disallowing use of any other DNS-program even on unused interfaces.
Tested-by: Vaasa Hacklab <info@vaasa.hacklab.fi>
Signed-off-by: Sami Olmari <sami@olmari.fi>
SVN-Revision: 47953
Add the option "--all-servers" which forces dnsmasq to send all
queries to all servers and then take the first answer.
Signed-off-by: Andréas Gustafsson <gurgalof@gmail.com>
SVN-Revision: 47857
When enabled the dnsmasq DHCP server allocates the IP addresses sequentially
starting from the lowest available IP address.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 46211
This patch backports the option --tftp-no-fail to dnsmasq and prevents the
service from aborting if the specified TFTP root directory is not available;
this might be the case if TFTP files are located on external media that might
occasionally not be present at startup.
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 45213
DNSMASQ has the ability to provide a menu to a pxeboot system, using
the --pxe-prompt and --pxe-service configuration options. The current
init.d script converting the "dhcp" file to "dnsmasq.conf" does not
find these options, but they are supported. This patch thus enables
the options.
Signed-off-by: Derek LaHousse <dlahouss@mtu.edu>
SVN-Revision: 44747
The --dhcp-boot option of dnsmasq does not require servername and serveraddress
arguments if the builtin tftp server is used.
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 44744
The --quiet-dhcp setting increases privacy by omitting DHCP lease logs including MAC addresses.
Signed-off-by: Lars Kruse <devel@sumpfralle.de>
SVN-Revision: 44006
