The revision is stored in a different register than it is in other
Broadcom switches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37995
These switches are integrated in some recent BCM53XX and BCM47XX SoCs
like the BCM53572.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37994
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.
Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 37993
The Linksys wrt310n v1 does not have a robo_reset config variable in
nvram, but GPIO Pin 8 is the pin needed for resetting the external
switch, Linksys hard coded it into their source code.
Thank you Devastator for testing.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37988
This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.
This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.
Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37977
- change patch numbers to group the related stuff together,
- add mtd prefix where it is missing,
- use hyphens in the patch names
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37974
This patch adds support for building firmware images for the
TP-Link TL-MR3040 v2. Tested and working on v2.1 hardware.
Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37964
I checked the GPL code drop from D-Link and tried to get the wireless
and LAN switch LEDs to light up. I found some references in
AthSDK/www/DIR-825_C1/bsp.h as well as
AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I
only got the led for 2.4GHz to work. Anyway, here's the patch.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37963
The skb is usually started by a padding which allows the protocols in the
network stack to add their headers in front of the payload. The skb can be
reallocated in case the preallocated padding is not large enough. This can for
example happen in the function __skb_cow which will check the requested extra
headroom and allocate more buffer when the requested headroom is bigger than
the available one. The extra buffer is aligned again to the multiple of the
NET_SKB_PAD of the target architecture.
The macro used to create the multiple of the NET_SKB_PAD is written in a way
which allows only values power two as alignment parameter. The currently used
value of 48 bytes can not be written as n ** 2 but as 2 ** 4 + 2 ** 5. The
extra buffer is therefore not always the multiple of 48 but can be 16, 64, 80,
128, 144 and so on. The generated values are also not monotonic (48 requested
bytes are mapped to 80 allocated bytes and 49 requested bytes are mapped to 64
allocated bytes).
These unexpected small values result in more reallocations of the buffer. This
was noticed prominently during tests between two QCA9558 720 MHz devices which
were connected via ethernet to PCs and had a HT40 802.11n 3x3 link between each
other. The throughput PC-to-PC during iperf TCP runs increased reliable from
186 Mibit/s to 214 Mibit/s in one direction and from 195 Mibit/s to 220 Mibit/s
in the other direction. This is a performance increase of ~14% just by reducing
the amount of reallocations.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 37948
Currently, the module causes an oops at least on rt5350. These patches
have been accepted upstream at:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 37931
BCM5365 (and probably other older variants) use a different phy id, so
the phy driver never attached for them.
Fix this by adding the appropriate phy id to the fixup and the phy
driver.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37906
b53_no_ops has no elements and b53_port_ops has one element, this makes
the code access some random memory when trying to access the mib
counter functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37895
