Since the driver doesn't know anything about (M)STP
we just hard-set the ports to be enabled if they are
part of the VLAN.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43938
- eliminate MV_CPUPORT; not necessary since we define
the CPU port(s) via Device Tree
- add STU and expand VTU operations
- update register names to match those of 88E61xx rather than
mvswitch's 88E6060
- use more consistent formatting
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43937
3.3 produced *.dtb files in arch/arm/boot/ while 3.14 will produce those
in arch/arm/boot/dts/, adjust the image makefile accordingly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43925
Most of the devices we support have between 16MiB and 32MiB of RAM
available.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43924
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43883
This patch fixes a wrong mask operation for the rt2880-compatible ralink devices.
The mask operation reads the actual flags and then logical combines it with the pin flag it want to set.
Unfortunally, for rising as for falling interrupt flags the actual flag status of the rising interrupts was used.
That caused a problem if you want to use more than one falling GPIO interrupt.
Now the correct (seperated) actual status is used for both, falling and rising.
Signed-off-by: Jonas Arndt <info@greenwire-elektronik.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43882
Move all AR8327/AR8337-specific driver code into a separate source file
ar8327.c and adjust patches so that ar8327.c is compiled if
CONFIG_AR8216_PHY is set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43845
Move several structure definitions and #defines from ar8216.c
to ar8216.h and move AR8327/AR8337 header stuff into a new
header file ar8327.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43844
modules build during the kernel compile phase are ignored anyway,
all modules should be built using KernelPackage in
package/kernel/linux/modules/*
selecting the appropriate config symbols there rather than in
target/linux/*/config-*
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43842
The following patches unfortunately didn't hit the kernel stable
branches yet, therefore cherrypicking them for OpenWRT here:
* bridge: fix netfilter/NF_BR_LOCAL_OUT for own, locally generated queries
* bridge: multicast: enable snooping on general queries only
* bridge: multicast: add sanity check for general query destination
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 43841
