Split seama-factory and seama-sysupgrade into smaller pieces (similar to
the ramips code) to make the image generation more flexible.
Also use standard pad-offset instead of adding a block of zeros at the
beginning of the image that is later cut off again. Standard pad-rootfs can
be used as the seal header doesn't contain an image size or checksum.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
General convention is to keep U-Boot and radio calibration
data (ART) mtd partitions marked as read-only.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Using pad-to instead of passing the optional padding to append-kernel
or append-rootfs. It could be that the value of a variable is passed.
In case the variable is empty no error is thrown.
Furthermore the purpose of the extra parameter is hard to get without
reading the code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The kernel size isn't passed to the append-kernel build step and the
resulting image bricks the device.
Fixes FS#168.
Signed-off-by: Mathias Kresin <dev@kresin.me>
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers
Default configuration:
- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space
Flash instruction (do it under U-Boot, using RS232):
1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers
Default configuration:
- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
rootfs part needs to be aligned to erase block size which is passed as
the 6th argument to Image/Build/Seama and is now 65536 since commit
commit 5119ee9 "ar71xx: fix bogus hardcoded kernel image size for Seama
images (fixes#20585)", but $(($(6) - 64)) still assumes that the
argument is a limit on kernel partition size, i.e. 1310720, so the
generated factory image is wrong in that the kernel will fail to find
the rootfs (FlySpray link at [1])
This patch will workaround it with the following steps
1. Calculate the required space for seama header and META data in step 5
2. Pre-padding 64 bytes to lzma-compressed loader
3. Generate correctly padded image-$(2).tmp
4. Strip out the padding
5. Seal it with seama utility
While at it convert seama to new build method
[1] FS#35 - mynet-n750 factory images don't find root partition,
https://bugs.lede-project.org/index.php?do=details&task_id=35
Reported-by: Steven Haigh <netwiz@crc.id.au>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Remove kmod-crypto-deflate and kmod-ledtrig-gpio as the device works the
same by default without them
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
- Remove old style device profiles and convert them to device definitions
within the image building code
- Fix the legacy build macros for the changed eval depth in the legacy
image build wrapper
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This reverts commit 59e98b27c9.
and
Revert "ar71xx: merge profiles into image building code"
This reverts commit 636089ead6.
these are still causing issues
Signed-off-by: John Crispin <john@phrozen.org>
The patch has been run-tested and the relevant dmsg logs are as the
following
[ 0.762447] Creating 5 MTD partitions on "spi0.0":
[ 0.767217] 0x000000000000-0x000000010000 : "u-boot"
[ 0.775139] 0x000000010000-0x000000020000 : "bdinfo"
[ 0.781014] 0x000000020000-0x000000fe0000 : "firmware"
[ 0.810558] 2 uimage-fw partitions found on MTD device firmware
[ 0.815043] 0x000000020000-0x000000170000 : "kernel"
[ 0.821925] 0x000000170000-0x000000fe0000 : "rootfs"
[ 0.827587] mtd: device 4 (rootfs) set to be root filesystem
[ 0.831937] 1 squashfs-split partitions found on MTD device rootfs
[ 0.837983] 0x0000005c0000-0x000000fe0000 : "rootfs_data"
[ 0.845621] 0x000000fe0000-0x000000ff0000 : "backup"
[ 0.851445] 0x000000ff0000-0x000001000000 : "art"
While at it, convert to new build method
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.
Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
