Commit graph

523 commits

Author SHA1 Message Date
John Crispin
541bede918 brcm47xx: fix module insert order
https://dev.openwrt.org/ticket/13811

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 37161
2013-07-04 13:31:13 +00:00
Florian Fainelli
6a4f2922f6 targets: prepare for supporting normal and initramfs images
In order to support both normal images and initramfs, ensure that each
target sets KERNELNAME properly so that the generic kernel building code
can copy the corresponding files over $(KDIR) with the appropriate
extension. Update the various paths to the kernel and wrapper images
from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo).

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 37049
2013-06-27 19:58:31 +00:00
John Crispin
39df8d1a45 brcm47xx: dont manually insmod switch drivers
Signed-off-by: John Crispin <bloic@openwrt.org>

SVN-Revision: 36993
2013-06-21 16:53:15 +00:00
Hauke Mehrtens
9492d445de brcm47xx: run make kernel_oldconfig for 3.9 kernel config
SVN-Revision: 36928
2013-06-12 14:51:50 +00:00
Hauke Mehrtens
87f994d16d brcm47xx: remove support for kernel 3.6
SVN-Revision: 36927
2013-06-12 14:48:45 +00:00
Hauke Mehrtens
990423f3ef brcm47xx: add initial support for kernel 3.9
SVN-Revision: 36926
2013-06-12 14:47:53 +00:00
Gabor Juhos
46225b99d9 kernel: update linux 3.8 to 3.8.13
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36724
2013-05-26 16:02:31 +00:00
Jonas Gorski
526aedb705 kernel: move CONFIG_MIPS_SEAD3 to generic
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 36617
2013-05-12 21:41:55 +00:00
Gabor Juhos
e57c7d6c12 kernel: update linux 3.8 to 3.8.12
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36576
2013-05-08 08:53:53 +00:00
Gabor Juhos
8a9fe26f20 kernel: update linux 3.8 to 3.8.11
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36507
2013-05-01 22:15:18 +00:00
Hauke Mehrtens
ca7f9638d5 broadcom-diag: support for the WNDR3700v3
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.

The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.

Signed-off-by: Owen Kirby <osk@exegin.com>

SVN-Revision: 36482
2013-04-28 21:11:17 +00:00
Hauke Mehrtens
7dee0dae35 brcm47xx: use kernel 3.8.10 as default kernel
The biggest change with this kernel is a new partition parser.

SVN-Revision: 36480
2013-04-28 18:25:16 +00:00
Hauke Mehrtens
00a7ace7cf brcm47xx: add board detection for NETGEAR WNDR4500 V2
SVN-Revision: 36478
2013-04-28 18:19:31 +00:00
Hauke Mehrtens
1bac172c44 kernel: update bcma and ssb for kernel 3.8+ to version from wireless-testing master-2013-04-26.
SVN-Revision: 36473
2013-04-28 16:52:11 +00:00
Gabor Juhos
36d4fd70bc kernel: update linux 3.8 to 3.8.9
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36453
2013-04-26 16:55:42 +00:00
Felix Fietkau
f58dcb59c6 kernel: backport SSB/BCMA changes in preparation for a compat-wireless update
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 36367
2013-04-19 12:39:40 +00:00
Hauke Mehrtens
4a46687d25 brcm47xx: use old partition names again for kernel 3.8
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.

Thank you russell for spotting this problem.

SVN-Revision: 36235
2013-04-06 22:22:26 +00:00
Hauke Mehrtens
204bde8d98 brcm47xx: fix error in board detection when nvram is not available.
SVN-Revision: 36234
2013-04-06 19:02:25 +00:00
Gabor Juhos
f78c902cfd kernel: update linux 3.8 to 3.8.6
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36215
2013-04-06 11:40:44 +00:00
Hauke Mehrtens
98ef9e5411 brcm47xx: generate images for Linksys E.... models
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 36139
2013-03-27 15:51:28 +00:00
Hauke Mehrtens
31c9452120 brcm47xx: activate image generation for some Netgear devices which are on the market and should be supported.
SVN-Revision: 36137
2013-03-27 15:35:52 +00:00
Hauke Mehrtens
a9e5a178ef brcm47xx: generate images for more WRT...N models
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 36136
2013-03-27 15:34:55 +00:00
Hauke Mehrtens
d5cf67297a brcm47xx: generate images for some more devices
These devices should be supported by trunk now.

SVN-Revision: 36099
2013-03-20 22:01:18 +00:00
Gabor Juhos
07532dca7f kernel: update linux 3.8 to 3.8.3
Also refresh the related generic/platform patches.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36039
2013-03-15 14:39:51 +00:00
Hauke Mehrtens
e1f24d99e1 brcm47xx: refresh config
SVN-Revision: 35948
2013-03-10 20:42:26 +00:00
Hauke Mehrtens
44ed7d664a brcm47xx: add some more partition parser fixes by Rafał Miłecki
SVN-Revision: 35912
2013-03-09 19:48:03 +00:00
Hauke Mehrtens
694050a4cf brcm47xx: netconfig: add bacis support for swconfig
Parse the cpu port from swconfig and explicitly mark the cpu port as tagged.

SVN-Revision: 35911
2013-03-09 19:24:43 +00:00
Hauke Mehrtens
04af8bd108 brcm47xx: bgmac: omit the fcs
This fixes #13058 and hopefully #12927

SVN-Revision: 35834
2013-02-28 13:27:21 +00:00
Hauke Mehrtens
9805096f48 brcm47xx: bgmac: update to version form netdev git repository
SVN-Revision: 35833
2013-02-28 13:24:39 +00:00
Hauke Mehrtens
2c34e1aba5 brcm47xx: use bcm47xx_board_get() and detect some more boards in flash partition driver
SVN-Revision: 35791
2013-02-25 20:56:37 +00:00
Hauke Mehrtens
5d3b728372 brcm47xx: board detection WNDR3400v2
WNDR3400v2 is based on BCM53xx . Image that is created breaks the router somehow therefore "#".

CFE and NVRAM contain different vars - example:
CFE line original: Device eth0:  hwaddr 74-44-01-37-C6-69, ipaddr 192.168.1.1, mask 255.255.255.0
CFE after openwrt: Device eth0:  hwaddr 00-FF-FF-FF-FF-FF, ipaddr 192.168.1.1, mask 255.255.255.0

Logs were posted earlier on this mailing list: https://lists.openwrt.org/pipermail/openwrt-devel/2012-July/016174.html
Different logs with factory firmware are in the wiki: http://wiki.openwrt.org/toh/netgear/wndr3400#wndr3400v2
(and on wikidevi for example)

Signed off by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 35790
2013-02-25 20:55:46 +00:00
Hauke Mehrtens
0f2fc0adfd brcm47xx: use same board detection code as kernel 3.8
SVN-Revision: 35770
2013-02-24 18:10:42 +00:00
Hauke Mehrtens
9afdb046d3 brcm47xx: do not use vlan0 any more.
The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.

This makes OpenWrt always use vlan1 and vlan2 instead.

SVN-Revision: 35704
2013-02-20 15:31:43 +00:00
Hauke Mehrtens
1a8218d6e4 brcm47xx: add initial support for kernel 3.8
This contains the following new bigger changes:
 * new partition parser which still could lake some features or have bugs
 * new nand flash driver
 * using physmap-flash flash driver for parallel flash
 * some changes to the serial flash driver

With these changes OpenWrt starts using more of the mainline flash drivers.

SVN-Revision: 35632
2013-02-16 20:28:24 +00:00
Hauke Mehrtens
ce6a7543fe brcm47xx: BGMAC - Adjust AutoLoad number to be prior to switch modules
Adjust the "AutoLoad" number for the BGMAC module to be prior
to the switch modules.  This probably isn't real important as
the modules are loaded in the correct order by preinit anyway.

Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>

SVN-Revision: 35625
2013-02-16 16:27:33 +00:00
Hauke Mehrtens
9de704a03b brcm47xx: improve cpuport detection for filesafe
Do not try to load bcm57xx.ko any more this is not needed for kernel 2.6 and 3.X
Ask the switch driver where the CPU port is.

SVN-Revision: 35624
2013-02-16 16:24:15 +00:00
Hauke Mehrtens
92d16f38d7 brcm47xx: fix network config on simpleshare
The included patch will generate a correct network configuration on the simpletech simpleshare.

Thank you for the patch Will Holmes (RealOpty)

This closes #12361.

SVN-Revision: 35623
2013-02-16 15:24:48 +00:00
Hauke Mehrtens
a21ba013f5 brcm47xx: handle return values of cfe_env_get() correctly.
This closes #12746.

SVN-Revision: 35622
2013-02-16 15:19:24 +00:00
Hauke Mehrtens
283bff02a2 brcm47xx: bgmac: fix unaligned accesses to network headers.
SVN-Revision: 35621
2013-02-16 14:38:17 +00:00
Hauke Mehrtens
5fed2916c3 brcm47xx: fix unaligned access to mac address
The mac address should be aligned to u16 to prevent an unaligned access
in drivers/ssb/pci.c where it is casted to __be16.

This closes #9824.

SVN-Revision: 35618
2013-02-16 13:46:00 +00:00
Hauke Mehrtens
d9580d224a brcm47xx: try to automatically detect if the wan port is at port 4 and not at port 0.
This should fix #13000.

SVN-Revision: 35617
2013-02-16 12:37:24 +00:00
Hauke Mehrtens
c0f6c75cf7 brcm47xx: if the cpuport of the switch is port 8 assume vlan0ports: "1 2 3 4 8" and vlan0ports: "0 8"
SVN-Revision: 35597
2013-02-14 12:38:16 +00:00
Hauke Mehrtens
54ca3eed5d brcm47xx: configure vlan correctly on some recent devices.
SVN-Revision: 35587
2013-02-13 16:05:52 +00:00
Hauke Mehrtens
4663d424a3 brcm47xx: add some more fixes to bgmac
Thank you Rafał Miłecki and Nathan Hintz

SVN-Revision: 35574
2013-02-12 20:10:38 +00:00
Hauke Mehrtens
7c0208b336 brcm47xx: update tg3 to the version send upstream
SVN-Revision: 35573
2013-02-12 20:09:15 +00:00
Hauke Mehrtens
07db9e8eab brcm47xx: fix name of kmod-ocf-ubsec-ssb
This also removes kmod-ocf, because kmod-crypto-ocf is automatically selected by kmod-ocf-ubsec-ssb.

Thank you Manuel Munz <freifunk@somakoma.de> for the patch.

SVN-Revision: 35509
2013-02-06 22:51:25 +00:00
Hauke Mehrtens
a52832164b brcm47xx: bgmac: make it possible to set the devices into promisc mode when it is already up
This fixes #12927.

SVN-Revision: 35507
2013-02-06 14:57:00 +00:00
Hauke Mehrtens
8ba8225686 brcm47xx: fix detection of Asus RT-N16
This fixes #12936.

SVN-Revision: 35492
2013-02-04 22:49:05 +00:00
Hauke Mehrtens
a1e3c0ca46 Add Failsafe support for Linksys E3000V1 / WRT610NV2
Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2
in /lib/preinit/05_init_interfaces_brcm.  The list of devices will need to
be expanded.  Is there a way to determine the correct cpu_port to use in a
generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if
"/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists?  Could
a similar method be used in "/etc/init.d/netconfig"?

Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>

SVN-Revision: 35491
2013-02-04 22:40:57 +00:00
Hauke Mehrtens
c2198aba32 brcm47xx: Fix switch config on 4716/53115 devices
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>

SVN-Revision: 35490
2013-02-04 22:38:37 +00:00