SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz
1. Load Ramdisk via U-Boot
To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
* 115200bps
* 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.
U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm
2. Load image via GUI
a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.
3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin
Signed-off-by: Steven Lin <steven.lin@senao.com>
To be able to use the camera module, start_x=1 has to be set in
config.txt. This will cause the bootloader to load the GPU firmware that
contain the extra video codecs. Install these firmware files.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
An upstream change broke brcmfmac when loaded with modparam roamoff=1.
As we are carrying a patch that enables roamoff by default on the
brcm2708 target to improve stability, wireless is currently broken
there. Add a patch to fix brcmfmac with roamoff=1.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
For the parameters tls-cipher and ncp-ciphers more than one option can
be used in the OpenVPN configuration, separated by a colon, which should
be implemented as a list in order to configure it more clearly. By
adding the new OPENVPN_LIST option to the openvpn.options file with the
tls-cipher and ncp-cipher parameters, uci can now add this option as a
"list" and the init script will generate the appropriate OpenVPN
configuration from it.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This is actually a build dependency for /dev/crypto support in openssl.
Since it is a kernel module, it belongs here anyway.
- Removed Nikos Mavrogiannopoulos as maintainer.
- Streamlined make flags
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
This reverts commit 41770add03.
The fwtool_check_image() procedure is used by `sysupgrade --test` which must
not alter the image under test in any way.
Currently, when the LuCI ui or any other sysupgrade wrapper first invokes
sysupgrade --test to verify the compatibility of the image and then calculates
the sha256sum over it, the resulting checksum will differ from the original
image since the test invocation will implicitely strip the metadata trailer.
To properly fix the underlying issue, the combined image checksumming code
must be modified to skip the metadata trailer.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The return value of a package prerm script is discarded and not returned
correctly by default_prerm(). This allows other operations like service
shutdown to "leak" their return value, prompting workarounds like commit
48cfc826 which do not address the root cause.
Preserve a package prerm script return value for use by default_prerm(),
sharing the corresponding code from default_postinst() for consistency.
Also use consistent code for handling of /etc/init.d/ scripts.
Run Tested on: LEDE 17.01.4 running ar71xx.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update the OpenVPN package to version 2.4.6, refresh patches and drop
menuconfig options which are not supported upstream anymore.
Also fix the x509-alt-username configure flag - it is not supported
by mbedtls and was syntactically wrong in the Makefile - and the
port-share option which has been present in menuconfig but not been
used in the Makefile.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
dfa4ede interface: fix return code of __interface_add()
a82a8f6 netifd: fix resource leak on error in netifd_add_dynamic()
fa2403d config: fix resource leaks on error in config_parse_interface()
85de9de interface: fix memory leak on error in __interface_add()
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
As automatic helper assignment is disabled in recent Linux kernels,
explicit rules must be added to the raw table for each helper.
While commit f50a524 in the firewall3 project added a set of default
rules and other additional related functionality, both this and the
alternative manual methods of defining these rules require kmod-ipt-raw.
Signed-off-by: Steven Honson <steven@honson.id.au>
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.
Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes
Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM: 256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes
Flashing requirements:
- needs a tftp server at 192.168.1.10/serverip.
- special 8P8C(aka RJ45)<->D-SUB9 Console Cable
("Cisco Console Cable"). Note: Both WNDAP6x0 have
a MAX3232 transceivers, hence no need for any separate
CMOS/TTL level shifters.
External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
= Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description =====
1. | 1 / High | 0 / Low | Use the internal antennae (default)
2. | 0 / Low | 1 / High | Use the external antennae
The external antennaes are only meant for the 2.4 GHz band.
One-way Flashing instructions via u-boot:
0. connect the serial cable to the RJ45 Console Port
Note: This requires a poper RS232 and not a TTL/USB adaptor.
1. power up the AP and interrupt the u-boot process at
'Hit any key to stop autoboot'
2. setup serverip and ipaddr env settings
Enter the following commands into the u-boot shell
# setenv ipaddr 192.168.1.1
# setenv serverip 192.168.1.10
3. download the factory.img image to the AP
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img
4. verfiy image integrity
Enter the following commands into the u-boot shell
# crc32 $fileaddr $filesize
If the calculated crc32 checksum does not match, go back to step 3.
5. flash the image
Enter the following commands into the u-boot shell
# nand erase 0x110000 0x1bd0000
# nand write ${kernel_addr_r} 0x110000 ${filesize}
6. setup uboot environment
Enter the following commands into the u-boot shell
# setenv bootargs
# setenv fileaddr
# setenv filesize
# setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
# setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
# setenv bootcmd 'run owrt_boot'
# saveenv
7. boot
# run bootcmd
Booting initramfs instructions via u-boot:
Follow steps 0 - 2 from above.
3. boot initramfs
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
# run addtty
# bootm ${kernel_addr_r}
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds u-boot environment access to the MX60(W) target.
"The environment size is one NAND block (128KiB on Buckminster).
We allocate four NAND blocks to deal with bad blocks which may
exist in the saved environment"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All apm821xx devices use u-boot and most of them have
an accessible u-boot environment. This patch adds the
necessary template file, but does not add the
uboot-envtools package to any of the targets.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
If I create following image:
define Device/engenius-m36
IMAGE/sysupgrade.bin := combined-image | append-metadata
endef
Sysupgrade then errors out:
Invalid image. Contents do not match checksum (image:cd285595eaf297370404ae0e2815ec1a calculated:2cf9a2286fb6b01af3ea189128017d44)
Image check 'platform_check_image' failed.
By removing the metadata from the image I get combined-image checksum
working again and sysupgrade works.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is not necessary to have iucode-tool present on target system to have
functional intel-microcode package. The build time dependency is kept.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
e520469b Update manual pages
54067256 Bump up version number to 1.35.0
c4d2eeee Update AUTHORS
f51e696e asio: Add stop() to listen_and_serve doc
a433b132 Merge pull request #1260 from nghttp2/h2load-non-final-response
cf48a56d Merge pull request #1238 from jktjkt/cmake-fix-libevent-detection
6cad1b24 nghttpx: Write mruby send_info early
3c393dca nghttpx: Fix assertion failure on mruby send_info with HTTP/1 frontend
17292445 h2load: Handle HTTP/1 non-final response
f6644a92 make clang-format
48998f72 Merge pull request #1222 from donny-dont/fix/declspec
15ff52f9 Update README
6c03bb14 Upgrade travis toolchain
524b4392 Fix travis build failure
859bf2bc Update manual pages
b5619fb1 h2load: Clarify that time for connect includes TLS handshake
dcbe0c69 nghttpx: Simplify move ctor and operator
2996c284 nghttpx: Cleanup
42e8ceb6 nghttpx: Convert API status code to enum class
1daf9ce8 nghttpx: Convert WorkerEventType to enum class
d68edf56 nghttpx: Convert MemcachedStatusCode to enum class
0c4e9fef nghttpx: Convert memcached op to enum class
571404c6 nghttpx: Convert MemcachedParseState to enum class
4d562b77 nghttpx: Convert LogFragmentType to enum class
e6225871 nghttpx: Convert connection check status to enum class
4bd075de nghttpx: Convert Http2Session state to enum class
b46a3249 nghttpx: Convert FreelistZone to enum class
4bd44b9c nghttpx: Convert dispatch state to enum class
1b42110d nghttpx: Make Downstream state enum class
0735ec55 nghttpx: Convert shrpx_connect_proto to enum class
00554779 nghttpx: Convert DNSResolverStatus to enum class
0963f389 nghttpx: Convert SerialEventType to enum class
1abfa3ca nghttpx: Make TLS handshake state enum class
f2159bc2 nghttpx: Convert UpstreamAltMode to enum class
b0eb68ee nghttpx: Convert shrpx_forwarded_node_type to enum class
e7b7b037 nghttpx: Convert shrpx_cookie_secure to enum class
5e4f434f nghttpx: Convert shrpx_session_affinity to enum class
20ea964f nghttpx: Convert shrpx_proto to enum class
d105619b src: Remove extra braces if possible
ec5729b1 Use std::make_unique
6c919695 Use C++14
46576178 Don't send Transfer-Encoding to pre-HTTP/1.1 clients
5e925f87 Update doc
153531d4 nghttpx: Use the same type as standard stream operator<<
f7287df0 Bump up version number to 1.35.0-DEV
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2cc4b99 file: use global exec timeout instead of own hardcoded limit
ecd1660 exec: increase maximum execution time to 120s
Also expose the socket and timeout options in /etc/config/rpcd for
easier use.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When restart is run on an init script, the script traps SIGTERM. This is
done as a workaround for scripts named the same name as the program they
start. In that case, the init script process will have the same name as
the program process, and so when the init script runs killall, it will
kill itself. So SIGTERM is trapped to make the init script unkillable.
However, the trap is retained when the init script runs start, and thus
processes started by restart will not respond to SIGTERM, and will thus
be unkillable unless you use SIGKILL. This fixes that by removing the
trap before running start.
Signed-off-by: Linus Kardell <linus@telliq.com>
4734108 mt7603: use mt7603_wtbl_clear on station removal
9428e34 mt7603: fix watchdog reset sequence
b3f82a3 mt7603: report PSE reset failures via debugfs
a301dec mt7603: add back PSE client reset code
94cebfc mt7603: fix handling lost interrupt events during watchdog reset
b38fe7d mt7603: only issue PSE reset on PSE stuck
da666a7 mt7603: issue PSE reset if firmware debug register indicates stuck queues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* chacha20,poly1305: fix up for win64
* poly1305: only export neon symbols when in use
* poly1305: cleanup leftover debugging changes
* crypto: resolve target prefix on buggy kernels
* chacha20,poly1305: don't do compiler testing in generator and remove xor helper
* crypto: better path resolution and more specific generated .S
* poly1305: make frame pointers for auxiliary calls
* chacha20,poly1305: do not use xlate
This should fix up the various build errors, warnings, and insertion errors
introduced by the previous snapshot, where we added some significant
refactoring. In short, we're trying to port to using Andy Polyakov's original
perlasm files, and this means quite a lot of work to re-do that had stableized
in our old .S.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
4b83102 treewide: switch to C-code style comments
70506bf treewide: make some functions static
d9872db interface: fix removal of dynamic interfaces
2f7ef7d interface: rework code to get rid of interface_set_dynamic
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
009ab91 mt76: clean up more unused EXPORT_SYMBOLs
963768d mt76x02: fix regression in tx station race condition fix
d7788cc mt76: mt76x02: make group_wcid the first member in struct mt76x02_vif
e65ad4c mt7603: make group_wcid the first member in struct mt7603_vif
7b1373e mt76: mt76x02: remove mt76x02_txq_init
a97127b mt76: replace sta_add/remove ops with common sta_state function
13f1e82 mt7603: clear wtbl entry for removed stations
90e2c1b mt7603: add mt7603_wtbl_set_skip_tx, change mt7603_wtbl_set_ps users
41931e4 mt7603: toggle skip_tx on station add/remove
d0fdf01 mt7603: avoid unnecessary wtbl writes for ps-filter
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Zinc no longer ships generated assembly code. Rather, we now
bundle in the original perlasm generator for it. The primary purpose
of this snapshot is to get testing of this.
* Clarify the peer removal logic and make lifetimes more precise.
* Use READ_ONCE for is_valid and is_dead.
* No need to use atomic when the recounter is mutex protected.
* Fix up macros and annotations in allowedips.
* Increment drop counter when staged packets are dropped.
* Use static constants instead of enums for 64-bit values in selftest.
* Mark large constants as ULL in poly1305-donna64.
* Fix sparse warnings in allowedips debugging code.
* Do not use wg_peer_get_maybe_zero in timer callbacks, since we now can
carefully control the lifetime of these functions and ensure they never
execute after dropping the last reference.
* Cleanup hashing in ratelimiter.
* Do not guard timer removals, since del_timer is always okay.
* We now check for PM_AUTOSLEEP, which makes the clear*on-suspend decision a
bit more general.
* Set csum_level to ~0, since the poly1305 authenticator certainly means
that no data was modified in transit.
* Use CHECKSUM_PARTIAL check for skb_checksum_help instead of
skb_checksum_setup check.
* wg.8: specify that wg(8) shows runtime info too
* wg.8: AllowedIPs isn't actually required
* keygen-html: add missing glue macro
* wg-quick: android: do not choke on empty allowed-ips
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
SSIDs may contain UTF8 characters but ideally hostapd should be told
this is the case so it can advertise the fact. Default enable this
option.
add uci option utf8_ssid '0'/'1' for disable/enable e.g.
config wifi-iface
option utf8_ssid '0'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
