Move the PHY fixup call to the PHY init loop.
Use ar8xxx_has_gige in the PHY init instead of passing the gigE
capability via function parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43333
Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set.
Fixes: ticket 17800
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43332
PHY init code in the switch-specific hw_init functions is mainly
identical. Factor it out into a generic ar8xxx_phy_init function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43331
Move phy fixup code from the chip-specific hw_init functions into a
fixup_phys callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43330
Currently there is a fixed 1000ms wait time after the switch was reset.
Most if not all switches need much less time to perform a reset.
Therefore replace the fixed wait time with polling for BMCR_RESET to
be cleared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43329
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43328
Boards that have more than one swconfig enabled switch will show the devices in
reverse order when call swconfig list. Fix this by using list_add_tail().
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43106
This allows tagged and untagged traffic together on the same port on ar8327
switch devices.
I looked at the first attempt to do this in r40777 (ar71xx: Fix tagged+untagged
operation on AR8327N (#12181)). I also set the vlan and port egress policies
like that change. But I change vlan_tagged in an less intrusive way. The
tagged/untagged decision is now based on the following rules:
- if vid != pvid then traffic is always tagged
- if vid == pvid then vlan_tagged stores if the traffic should be tagged
Tested on TP-Link WDR-3600 (ar8327N).
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
SVN-Revision: 42653
This moves ingress, egress policy and pvid decisions to setup_port methods.
They arenow device type dependent.
This allows policy changes on only one device type which is needed to allow
tagged + untagged operation on ar8327.
Tested on TP-LINK WDR-3600 (ar8327N).
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
SVN-Revision: 42652
There are pretty many OpenWrt patches against mtd subsystem resulting
in a bit of mess and growing maintenance cost.
My idea is to use an extra "mtdsplit" directory with OpenWrt specific
files (including Kconfig).
This is the first step to achieve this. This patch adds a "mtdsplit"
directory with Kconfig and replaces 4 patches with a single one.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42287
According to the thread https://forum.openwrt.org/viewtopic.php?id=48281
b53 uses GPIO 7:
[ 4.470000] b53_common: [DBG] b53_switch_reset_gpio using 7
and causes device to self-reboot. GPIO 8 was found in CFE boot log:
"Reset switch via GPIO 8 ..."
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41526
This patch deactivates the statistics, adds a missing lock
initialization and fixes a waring.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41511
Revert the tagged + untagged rework for now due to regressions in
vlan setup on certain AR83xx switches.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 40842
Replace the global "vlan_tagged" variable with an array storing the
tagging state per vlan.
The code was taken from #12181, tested and cleaned up by Saverio Proto
with additional bug fixes supplied by Álvaro Fernández.
Tested-by: Jo-Philipp Wich <jow@openwrt.org>
Signed-off-by: Saverio Proto <zioproto@gmail.com>
Signed-off-by: Álvaro Fernández <noltari@gmail.com>
SVN-Revision: 40777
Function register_mtd_parser always returned 0 (at least since v3.3)
before being changed to return void in v3.14-rc1~65^2~93 (mtd: make
register_mtd_parser return void), so it's not needed to check the
return value of this function. Also add __init flag to caller.
This fix compile errors in 3.14 kernel like:
drivers/mtd/mtdsplit_seama.c: In function 'mtdsplit_seama_init':
drivers/mtd/mtdsplit_seama.c:99:2: error: void value not ignored as it ought to be
return register_mtd_parser(&mtdsplit_seama_parser);
^
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
SVN-Revision: 40731
This patch adds port status information and MIB counters to the ADM6996
switch driver.
The driver supports also the older ADM6996L-variant, but I'm not able to
test this patch on that chip. According to the datasheet the same
registers exist there as well, so I think it should work, but any
feedback is appreciated.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40542
If the CPU port is not forced up, the link, at least on this board, is lost after
changes are applied. This makes sure that the link is restored. Regression tests
should confirm it doesn't break other boards.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40305
- hide port pvid - vlan index relation
- switch initialises with vlans disabled so port isolation is not used
- remove special treatment of cpu port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40304
Changes to:
- show the correct "enable_vlan" value under "Global attributes"
- show tagged ports under "Vlan: ports"
- use get_port_link method to report link status
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40303
Use the 'swconfig_trig_set_brightness' function to set
the brightness value of the LED when the link goes down.
This ensures that the last brighness value is saved into
a local variable which is used to track the actual LED
status.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39402
This reverts r38197.
The automatically created firmware partition includes
the partition_table partition. Apart from the partition
table, this partition contains sensitive data on some
Compex devices which data can be destroyed when the
firmware partition gets modified. Revert the change to
prevent that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39382
This patch enables jumbo frames on AR8327 switch by default.
I have tested it on TP-Link TL-WDR3600.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39076
This patch is needed to use the switch inside the Sitecom WLR-8100;
it was unusable and detected as Generic-Phy before.
since ar8337 is behaving like ar8327
generally do the same thing
see: https://forum.openwrt.org/viewtopic.php?pid=214218#p214218
forward-ported to trunk
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4469/
[juhosg: merge chip_is_ar83[23]7 statements in ar8xxx_phy_config_init]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38952
The BCM5365 needs a shift of 7 bits and not 6 bits like the BCM5325 for
the untagged ports.
Thank you Russell for reporting this and testing the patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38793
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
The GPIO bit banging protocol implementation was copied from the old
switch driver and adapted to this driver and changed to the mainline
kernel GPIO interface.
The ADM6996L is different from the ADM6996M which is supported, for
both specs are available in the Internet.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38698
The revision is stored in a different register than it is in other
Broadcom switches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37995
These switches are integrated in some recent BCM53XX and BCM47XX SoCs
like the BCM53572.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37994
The Linksys wrt310n v1 does not have a robo_reset config variable in
nvram, but GPIO Pin 8 is the pin needed for resetting the external
switch, Linksys hard coded it into their source code.
Thank you Devastator for testing.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37988
BCM5365 (and probably other older variants) use a different phy id, so
the phy driver never attached for them.
Fix this by adding the appropriate phy id to the fixup and the phy
driver.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37906
b53_no_ops has no elements and b53_port_ops has one element, this makes
the code access some random memory when trying to access the mib
counter functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37895
The myloader partition parser code uses ifdef wrappers
to make the code usable on kernels below version 3.2.
All targets are using kernel 3.3 at least so the wraper
is not needed. Remove that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37880
This is needed for some switches used on bcm47xx SoCs like the one on the Asus RT-N66U.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37645
There is no platform using the gpio-pwm driver, yet these patches break the
generic PWM framework that is in upstream. So just remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 37490
It hasn't been buildable for a long time, and there are no users of it
anymore left as all of them have been switched to the upstream accepted
version.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37436
This makes it possible to use swconfig to controll the switch.
This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.
SVN-Revision: 37304
This patch adds swlib attributes to the RTL8366RB switch/PHY found in the
TL-WR1043ND router that allow to mirror ethernet packets to a monitor port.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36847
Tested on Buffalo WZR-600DHP with ar8316 switch. Commands used to mirror both
RX and TX traffic from LAN port 1 to LAN port 4:
$ swconfig dev switch0 set enable_mirror_rx 1
$ swconfig dev switch0 set enable_mirror_tx 1
$ swconfig dev switch0 set mirror_monitor_port 4
$ swconfig dev switch0 set mirror_source_port 1
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 36713
drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_sw_set_vlan_ports':
drivers/net/phy/rtl8366_smi.c:1125:6: warning: 'pvid' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36442
* disable external interface if its property is not present
* show an error message if the extif property is not valid
* use proper error values intead of -1
* fix memory leak
* wrap long lines
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36229
The AR8327 switch gets its configuration from platform
data or from the device-tree. This allows to start it
from the probe routine. Doing so makes it usable with
ethernet drivers which only connects to the PHY device
when the ethernet interface is opened.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36050
Move switch starting code into a separate function.
This makes it usable from other places.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36049
Move platform_data specific configuration code
into a separate routine. Do it in preparation
for the upcoming OF support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36046
Fetch the PORT_STATUS values in ar8327_hw_init and
store those in a private data stucture for later use.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36045
Return with the PORT_STATUS register value instead of
writing that directly into the corresponding register.
Also rename the function to ar8327_get_port_init_status.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36043
The presence of the platform data is already verified in
ar8327_hw_init, and the driver does not start without that
anyway.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36042
Setting this bit stops BCM53125 (bgmac actually) from receiving any
packets. This bit is cleared conditionally in b53_switch_reset and it
seems the same is done in bcmrobo.c which never sets that bit again.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 35723
