Commit graph

19031 commits

Author SHA1 Message Date
Marc Benoit
e40db2907e kernel: iqp806x low latency kernel does not boot
It keeps failing (R7800) with the stack trace below

BUG: scheduling while atomic: kworker/0:1/26/0x00000002

(unwind_backtrace) from [<c02121d0>] (show_stack+0x10/0x14)
(show_stack) from [<c03932e4>] (dump_stack+0x7c/0x9c)
(dump_stack) from [<c0239b90>] (__schedule_bug+0x5c/0x80)
(__schedule_bug) from [<c05b7260>] (__schedule+0x50/0x3f4)
(__schedule) from [<c05b76a8>] (schedule+0xa4/0xd4)
(schedule) from [<c05ba430>] (schedule_hrtimeout_range_clock+0xc8/0x100)
(schedule_hrtimeout_range_clock) from [<c05ba480>]
       (schedule_hrtimeout_range+0x18/0x20)
(schedule_hrtimeout_range) from [<c05b9f78>] (usleep_range+0x48/0x50)
(usleep_range) from [<c03f333c>] (__clk_hfpll_enable+0x44/0xd0)
(__clk_hfpll_enable) from [<c03f3474>] (clk_hfpll_set_rate+0xac/0xc4)
(clk_hfpll_set_rate) from [<c03ec390>] (clk_change_rate+0xf4/0x1fc)
(clk_change_rate) from [<c03ec510>] (clk_core_set_rate_nolock+0x78/0x94)
(clk_core_set_rate_nolock) from [<c03ec54c>] (clk_set_rate+0x20/0x30)
(clk_set_rate) from [<c0424168>] (dev_pm_opp_set_rate+0x190/0x26c)
(dev_pm_opp_set_rate) from [<c04a8548>] (set_target+0x40/0x108)
(set_target) from [<c04a4.140>] (__cpufreq_driver_target+0x3f4/0x488)
(__cpufreq_driver_target) from [<c04a7494>] (od_dbs_timer+0xcc/0x154)
(od_dbs_timer) from [<c04a7998>] (dbs_work_handler+0x2c/0x54)
(dbs_work_handler) from [<c02309e8>] (process_one_work+0x1c0/0x2f0)
(process_one_work) from [<c02319a8>] (worker_thread+0x2a4/0x404)
(worker_thread) from [<c0235944>] (kthread+0xd8/0xe8)
(kthread) from [<c020eef0>] (ret_from_fork+0x14/0x24)

Signed-off-by: Marc Benoit <marcb62185@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
05f53eecca ipq806x: define KERNEL_SIZE in KB instead of byte for the image generation
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
c3af761e47 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 R7500v2
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500v2.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
c228bbe616 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 R7500
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
45b8a7c1a6 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 D7800
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 D7800.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Tathagata Das <tathagata@alumnux.com>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
0c967d92b3 ipq806x: increase kernel partition size for the TP-Link Archer VR2600v
The default image does not fit 2 MB anymore, expand kernel partition
to 3 MB.

Upgrading should work transparently via sysupgrade in both directions.
Another option would be to merge "kernel" and "rootfs" into a single
"firmware" partition using MTD_SPLIT_TPLINK_FW, but just changing the
sizes of the existing partitioning has been deemed safer in the absence
of an actual runtime test on an affected device; the maximum for rootfs
changes from 10.4 MB to 9.4 MB.

This change follows the example for the TP-Link Archer C2600, but has
not been runtime tested on a TP-Link Archer VR2600v.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Sebastian Quilitz <zeraphim@x-pantion.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
b72b36653a ipq806x: increase kernel partition size for the TP-Link Archer C2600
The default image does not fit 2 MB anymore, expand os-image partition
to 4 MB.

Upgrading works transparently via sysupgrade in both directions.
Another option would have been to merge "os-image" and "rootfs" into a
single "firmware" partition using MTD_SPLIT_TPLINK_FW, but just
changing the sizes of the existing partitioning has been deemed safer
and actually tested on an affected device; the maximum for rootfs
changes from 27 MB to 25 MB.

Run-tested on TP-Link Archer C2600.

Signed-off-by: Joris de Vries <joris@apptrician.nl>
[slh: extend comments and commit message, rename rootfs]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Stefan Lippers-Hollmann
dc50694bd1 ipq806x: increase kernel partition size for the Netgear r7800
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This patch is based on a corresponding change by Pavel Kubelun
<be.dissent@gmail.com> and has been tested by Michael Yartys
<michael.yartys@protonmail.com>

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Ram Chandra Jangir
7ac6697fe2 ipq806x: cleanup kernel config
Disable MSM8960, MSM8974 and APQ8084
 - since these are different SoC's than IPQ806x
Removed unrequired serial configs
 - since ipq806x uses SERIAL_MSM only

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
Ram Chandra Jangir
93dd2f7211 ipq806x: add kernel 4.14 support
- Rebased the patches for 4.14
 - Dropped spi-qup and 0027, 0028, 0029
   clk patches since it's already included
   in upstream.

 Tested on IPQ AP148 Board:
  1) NOR boot and NAND boot
  2) Tested USB and PCIe interfaces
  3) WDOG test
  4) cpu frequency scaling
  5) ethernet, 2G and 5G WiFi
  6) ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-05-22 20:34:14 +02:00
David Bauer
70e6ea319d ipq40xx: add eva-image for FRITZ!Box 4040
This commit adds an EVA flashable image for the FRITZ!Box 4040.

The image contains the U-Boot with OpenWRT appended to it. This way we
remove the need to use UART for initial flashing.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-22 20:34:14 +02:00
David Bauer
ce91c85e01 ramips: change wifi led trigger for Archer C50v3
This commit alters the TP-Link Archer C50v3 LED settings to use the phy
trigger instead of the netdev one. This way the WiFi status is displayed
even if the wifi interface name is altered.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-22 20:34:14 +02:00
David Bauer
35d00d9a41 ramips: fix Archer C50v3 LED mapping
This commit fixes the wrong LED mapping of the Archer C50 v3.
Commit was tested with an EU device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-22 20:34:14 +02:00
Lucian Cristian
71cec0b194 ath79: enable rtl8366rb phy
is needed for at least tplink wr1043nd-v1

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-05-22 20:34:14 +02:00
Lucian Cristian
fe594bf90d ath79: fix loader-okli, lzma-loader
booting will hang most of the times on tl-wr1043nd-v1 without a KERNEL_CMDLINE value
add anything as a placeholder as kernel command line is taken from DTS

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-05-22 20:34:14 +02:00
Chuanhong Guo
a789c0f491 ar71xx: Add support for PISEN TS-D084
PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0

Flash instruction:
The manufacturer are using exactly the same firmware header as TP-LINK TL-WR703N (including device ID!). Simply upload the factory firmware into WebUI and flashing is done.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-05-22 07:58:16 +02:00
Sergey Ryazanov
67a3cdcbb0 kernel: enable THIN_ARCHIVES by default
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:20 +02:00
Sergey Ryazanov
bdc2b58c4b kernel: enable FUTEX_PI by default
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:12 +02:00
Sergey Ryazanov
a08b0d0c31 kernel: enable EXPORTFS by default
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:05 +02:00
Sergey Ryazanov
978543a246 kernel: disable DRM_LIB_RANDOM by default
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:57 +02:00
Sergey Ryazanov
ead26e9db6 kernel: disable DMA_{NOOP|VIRT}_OPS by default
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:49 +02:00
Sergey Ryazanov
f928c338ad kernel: disable ARCH_WANTS_THP_SWAP by default
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:42 +02:00
Evgeniy Didin
a2418dba02 arc770: remove source-only
In commit 8b9cdebc9c ("arc770: mark as source-only") arc770 was marked
as source-only because of iproute2 compile issues.
With uClibc-ng version 1.0.30 issues with iproute2 were fixed.
Lets remove "source-only" for arc770 as soon as uClibc-ng version
will be updated to 1.0.30. Patch for uClibc-ng is here:
https://patchwork.ozlabs.org/patch/917547/

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
2018-05-22 07:20:26 +02:00
Hauke Mehrtens
ae8ff1c65c ar71xx: Fix build for dap-1330-a1 board
Using a version number of 16 character causes a buffer overflow in the
version number overwriting the first bit of the signature in the
mkdapimg2 tool.
I am not sure if the version number should be null terminated or not.
This patch reduces the size of the version number by removing the number
of private commits from it.

This was the original version number which caused problems:
OpenWrt-r6727+10
Now it uses this version number:
OpenWrt-r6727

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-05-22 07:20:26 +02:00
Sergey Ryazanov
06116473cc ath25: drop 4.9 kernel support
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:20:13 +02:00
Sergey Ryazanov
5191ea5621 ath25: switch to 4.14 kernel
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 06:42:14 +02:00
Sergey Ryazanov
3d69857ac1 ath25: add kernel 4.14 support
Copy and refresh patches and config from 4.9, no more work is need.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 06:41:57 +02:00
Damir Samardzic
5b7b0c68c7 mvebu: initial support for Marvell Armada 7k and 8k DB boards
Add initial support for cortex-a72 based Armada DB-88F8040-Modular and
DB-88F7040-Modular development boards.

DB-88F8040-Modular specifications:
- Quad-core ARMv8 Cortex A72 CPU (up to 2 GHz)
- DDR4 DIMM - 64 bits + ECC
- 2 x 128 Mb SPI NOR flash memory
- 2 x 1G Ethernet port via RGMII (RJ45)
- 2 x SD card ports (4 bit port on CP, 8 bit port on AP)
- 2 SERDES modules with the following interfaces each:
  - 2 x SATA Rev 3.0 port (Port1 via SERDES module CON4 (active port), Port0
    via SERDES Module CON2 or CON1 (optional port))
  - 3 x PCI Express (PCIe) Gen 3.0 (Port2 via SERDES module CON5 (active port),
    Port1 via SERDES module CON7 (optional port), Port0 via SERDES module CON6
    (optional port))
  - 2 x USB3 (USB 2.0 backward compatible) host (via SERDES module CON9 and
    CON10)
  - 1 x 10G port over SFP+ connector (via SERDES module CON8)
- 1 x MCI interface by two over USB Type C connector
- 4 x serial COM port driven by the 88F8040 UART interface and converted to
  USB via FTDI IC
- I2C Master Interface
  - CP I2C 2x EEPROM @ Address 0x50 and 0x57
  - 1 x I/O Expander @ Address 0x21
  - Sample at Reset (SatR) memory device @ Address 0x4C and 0x4E
- I2C Slave Interface (via SERDES module) - Connection to each device on the
  board via an I2C multiplexer
- JTAG interface for CPU emulator
- Board dimensions: 270 mm x 240 mm (main + SERDES module)
- SERDES Module Dimensions: 70 mm x 105 mm

DB-88F7040-Modular specifications:
- Quad-core ARMv8 Cortex A72 CPU
  - CPU core operating speed of up to 1.6 GHz for Dual Core, 1.4 GHz for Quad
    Core
- DDR4 - 32 bit + ECC on Module - SLM1366-V1 (DB-DDR4-40B-MODULE) 4 GByte
  32-bit
- 1 x 128Mb SPI NOR flash memory
- 2 x 1G Ethernet port: 1 over RGMII (RJ45) and 1 over SGMII
- SD card 4 bits port on AP
- eMMc Module on CP
- 1 SERDES Modules with the following interfaces each:
  - 1 x SATA Rev 3.0 port (via SERDES module CON4)
  - 1 x PCI Express (PCIe) Gen 3.0 (via SERDES module CON5)
  - 2 x USB 3.0 (USB 2.0 backward compatible) host (via SERDES module CON9 and
    CON10)
  - 1 x 10G port over SFP+ connector (via SERDES module CON8)
- 2 x MCi interface by one over USB Type C connector
- 4 x Serial COM port driven by the 88F7040 UA
- RT interface and converted to USB via FTDI IC
- I2C Master Interface
  - 2 x EEPROM at address 0x57 and 0x50 in AP and 2 x EEPROM at address 0x57
    and 0x50 in CP
  - 1 x I/O Expander at address 0x21
  - Sample at Reset (SatR) memory device at address 0x4C and 0x4E
- I2C Slave Interface (via SERDES module) - Connection to each device on the
  board via an I2C multiplexer
- JTAG interface for CPU emulator
- Board dimensions - 270 mm x 240 mm (main + SERDES module)
- SERDES Module Dimensions - 70 mm x 105 mm

Booting from USB flash drive (dd sdcard image to the flash drive):
 1. reset U-Boot environment:
      env default -a
      saveenv

 2. prepare U-Boot manually (make sure to set correct dtb file name):
      setenv bootargs_root 'root=/dev/sda2 rw rootdelay=2 ip=dhcp'
      setenv fdtfile armada-7040-db.dtb
      setenv image_name Image
      setenv bootcmd 'usb start; ext4load usb 0:1 $kernel_addr $image_name; ext4load usb 0:1 $fdt_addr $fdtfile; setenv bootargs $console $mtdparts $bootargs_root; booti $kernel_addr - $fdt_addr'
      saveenv
      boot

Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
2018-05-21 18:07:47 +02:00
Damir Samardzic
322a02f666 mvebu: initial support for Marvell Armada 3720 DB board
Add initial support for Marvell Armada cortex-a53 based
DB-88F3720-DDR3-Modular development board.

Specifications:
- Dual core ARMv8 Cortex-A53 CPU (up to 1.0 GHz)
- 4Gb 16-bit DDR3/3L DRAM memory
- 128Mb SPI NOR flash memory
- 8Gb eMMC NAND flash memory
- 1 x SATA Rev 3.0 port
- 1 x PCI Express (PCIe) Gen 2.0 or 1 x mini PCI Express (PCIe) Gen 2.0
- 1 x 1G Ethernet port via RGMII (RJ45)
- 1 x SD card port
- 1 x USB3 (USB2 backward) host\device port via type C connector
- 1 x USB2 host port via type A connector
- 1 x serial COM port driven by the 88F3720 UART interface and converted to
  USB via FTDI IC (option to connect the UART DB9 adapter)
- I2C Master Interface:
  - 1 x EEPROM @ address 0x57
  - 1 x I/O Expanders @ address 0x22
  - Sample at Reset (SatR) memory device @ address 0x4C
  - RTC clock generator PT7C4337AWE @ address 0x68
  - USB3 switch PI5USB30213XEA @ address 0x0D
  - ID component of PHY module @ address 0x24
- 1 x JTAG interface for CPU emulator
- 1 x SETM and JTAG debug interface
- 1 x power connector for HDD supply
- 1 x 12V DC jack power connector
- Board dimensions: 150 mm x 179 mm
- LED interface for system status

Booting from SD card:
 1. reset U-Boot environment:
      env default -a
      saveenv

 2. prepare U-Boot with boot script:
      setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
      saveenv

    or manually:
      setenv fdt_name armada-3720-db.dtb
      setenv image_name Image
      setenv bootcmd 'mmc dev 0; ext4load mmc 0:1 $kernel_addr $image_name;ext4load mmc 0:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr'
      saveenv

Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
2018-05-21 18:07:47 +02:00
YuheiOKAWA
13684ba63f kernel: Add support spi-nor, Eon EN25QH32
Support Add spi-nor chip EN25QH32. JEDEC is 1c7016.

Can't boot issue, new revision hardware is EN25QH32 flash chip.
example, MZK-DP150N (ramips).
https://bugs.openwrt.org/index.php?do=details&task_id=1534

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-05-21 18:07:47 +02:00
Alif M. Ahmad
b0a51dab8c x86: disable CONFIG_EFI_VARS
Disable CONFIG_EFI_VARS, since it suffers from sysfs limitation (no
support for variable longer than 1024 bytes).

kmod-fs-efivarfs is the replacement of this, which enables mounting
efivarfs file system and doesn't suffer from 1024 bytes limitation.

Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
2018-05-18 11:19:00 +02:00
YuheiOKAWA
d91953cb53 ramips: add support for YUKAI Engineering Inc. BOCCO
BOCCO is a communication robot provided by YUKAI Engineering Inc.

SoC: MT7620A
MEM: 256MB
Flash: 8MB
NAND: 512MB (non support)
Include Sound DAC and AMP.
No Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-05-18 11:19:00 +02:00
Michal Cieslakiewicz
45dc530334 ar71xx: WNDR3700: enable RFKILL function for Wifi button
Wifi button for WNDR3700 dual band routers has been renamed to "rfkill"
and its emitted keycode changed to KEY_RFKILL. This allows OpenWrt/LEDE
to support it 'out of the box' without additional tweaking.

Until this patch, button had been sending BTN_2 keycode which was
ignored by default (no action script present). To get expected behaviour
of switching radios on and off, user had to manually rename/link
'rfkill' script to name 'BTN_2' in /etc/rc.button directory.

This patch follows similar changes for other Netgear ar71xx routers,
for example WNR2000v3. It applies cleanly to both latest trunk and 17.01
branch. Tested on WNDR3700v1.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2018-05-18 11:18:53 +02:00
Christian Lamparter
707b6c815b brcm2708: add squashfs rootfs image
This patch adds a image with squashfs as the root filesystem.
A rootfs_data partition will be generated on the first boot
and placed inside the rootfs partition (just after the squashfs
image).

advantages:
 - it is possible to migrate from an existing -ext4
   installation and back via sysupgrade.
 - existing partition layout will not be lost.
 - slightly smaller image size.
 - support for attendedsysupgrade

disadvantages:
 - needs f2fs + tools as well. This is because fs-tools decides on the
   blocksize of the sdcard. So either f2fs or ext4 can get choosen as
   the rootfs_data filesystem (depends on the size of the root partition).
 - rootfs_data is placed into the rootfs partition. This makes
   it difficult for tools that expect a /dev/mmc0pX device.
   It also makes it difficult for data recovery tools since they
   might not expect to find a embedded partition or will be
   confused.

For people with existing build configurations: make sure to include mkf2fs
and f2fsck package into the image... Otherwise the new -squashfs image will
boot of a ram-overlay and won't keep the configurations after a reboot.

Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: Paul Spooren <spooren@informatik.uni-leipzig.de>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
2018-05-18 09:17:49 +02:00
Kristian Evensen
8f9baf5e1a x86: Add APU3 reference to x86 board.d
There is a new APU-model available, APU3. The device is configured in
the same way as the APU1 and APU2, so the same LED/network setup can be
used.

I considered changing the case to pc-engines-apu*, but I chose to follow
the existing pattern and add the full board name.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2018-05-18 09:17:24 +02:00
Christian Lamparter
16e39624b7 apm821xx: backport and reassign crypto4xx patches
This patch backports several patches that went upstream into
Herbert Xu's cryptodev-2.6 tree:

crypto: Use zeroing memory allocator instead of allocator/memset
crypto: crypto4xx - performance optimizations
crypto: crypto4xx - convert to skcipher
crypto: crypto4xx - avoid VLA use
crypto: crypto4xx - add aes-ctr support
crypto: crypto4xx - properly set IV after de- and encrypt
crypto: crypto4xx - extend aead fallback checks
crypto: crypto4xx - put temporary dst sg into request ctx

The older, outstanding patches from 120-wxyz series have been
upstreamed as well and therefore they have been reassigned to
fit into the series.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-05-18 09:14:09 +02:00
Christian Lamparter
e6e51ce87f apm821xx: don't select swconfig for the MR24
The swconfig package is part of the DEFAULT_PACKAGES list in
the apm821xx's nand subtarget. It's enabled by default because
the MX60(W) and WNDR4700 need it for their initramfs. However
the package is not necessary for the MR24's sysupgrade image, as
the MR24 does not have a switch.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-05-18 09:13:19 +02:00
Roman Yeryomin
1f42deec8e ipq40xx: fix ethernet on ap-dk01.1
Not sure how it worked before but ethernet is disabled
by default in ipq4019 dtsi.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-18 09:12:53 +02:00
Koen Vandeputte
e2aa0c3f8b kernel: bump 4.14 to 4.14.41
Refreshed all patches

Dropped upstreamed patches:
522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch
523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch
525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch
527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch

updated patches:
524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch
030-USB-serial-option-fix-dwm-158-3g-modem-interface.patch

Added new ARM64 symbol: CONFIG_ARM64_ERRATUM_1024718

Compile-tested on: cns3xxx, imx6, mvebu (arm64), x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-05-18 09:10:46 +02:00
Koen Vandeputte
12f44b83a8 kernel: bump 4.9 to 4.9.100
Refreshed all patches

Added new ARM64 symbol: ARM64_ERRATUM_1024718

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-05-18 09:10:21 +02:00
Daniel Gonzalez Cabanelas
fbbb977772 brcm63xx: Tune the network configuration for several routers
- DGND3700v1: fix port numbers, they're in reverse order
- FaST2704n: there is no WAN port identified as such, only 4 LAN
- AD1018: configure the "FIBRE" port as WAN

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2018-05-18 08:55:37 +02:00
Rosen Penev
fec205f654 ramips: mmc: Sync with staging driver
Mostly whitespace cleanups. Some unneeded code was removed.

MMC init was also moved to the probe function as in
6069bdd

The cleanup commits are over 100, making it hard to do them individually.

Tested on GnuBee PC1 with an SD card being used as swap.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
v2: Fixed compile issue with mt7620
2018-05-18 08:49:52 +02:00
Matthias Schiffer
a5b77c9d9d
ath79: remove unused copy-file build step
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-05-17 22:11:56 +02:00
Matthias Schiffer
aea146736c
ath79: fix TP-Link TL-WR1043ND v1 image build
Both initramfs and flashed images are built and boot. No Ethernet, no WLAN,
probably further issues, so the image is not added to TARGET_DEVICES for
now.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-05-17 22:11:56 +02:00
Felix Fietkau
e9cb1b720d netfilter: fix hardware offload regression (FS#1551)
The relevant code needs to be enabled even if flow table support is only
compiled as module

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-17 08:21:54 +02:00
Mathias Kresin
75ed56a08a ath79: add AVM FRITZ!WLAN Repeater 300E
No known issues, everything works fine.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
bc04cf780e ath79: ar724x: fix pll settings
Add the syscon compatible, otherwise used functions like
syscon_regmap_lookup_by_phandle() will return an error and setting the
ethernet pll data wont work at all.

Fix the pll register width. Writing to registers out of the range via
syscon isn't possible and returns an error. On ar7242 the last pll
register - Current Audio Modulation Logic Output - is at 0x1805003c.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
f7ec385c13 ath79: add and enforce image metadata
Add metadata to images and make the metdata mandatory.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
f77db1a590 ath79: cleanup image build code
Remove recipes for not yet migrated boards. Drop variables which aren't
required due to the switch to devicetree like boardname.

Drop the legacy image build code. Boards added to this target shouldn't
use the legacy image build code anyway.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
cfe442c503 ath79: sysupgrade: drop unused variables
None of the variables are used at the moment.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00