In order to set the multicast rate for mesh point interfaces the "mesh join"
was made explicit and moved to mac80211_setup_vif(), similar to how it is
done for IBSS interfaces.
Previously, the mesh join was made implicit in case authentication (i.e.
$key) was not used when creating the interface in mac80211_prepare_vif(),
while using authentication would create the interface first, then join
later in mac80211_setup_vif() by starting authsae.
Signed-off-by: Nils Schneider <nils@nilsschneider.net>
SVN-Revision: 47408
llid_in_use needs to be limited to stations of the same VIF, otherwise it
will cause a NULL deref as the sta_info of non-mesh-VIFs don't have
sta->mesh set.
Steps to reproduce:
modprobe mac80211_hwsim channels=2
iw phy phy0 interface add ibss0 type ibss
iw phy phy0 interface add mesh0 type mp
iw phy phy1 interface add ibss1 type ibss
iw phy phy1 interface add mesh1 type mp
ip link set ibss0 up
ip link set mesh0 up
ip link set ibss1 up
ip link set mesh1 up
iw dev ibss0 ibss join foo 2412
iw dev ibss1 ibss join foo 2412
# Ensure that ibss0 and ibss1 are actually associated; I often need to
# leave and join the cell on ibss1 a second time.
iw dev mesh0 mesh join bar
iw dev mesh1 mesh join bar # crash
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47364
The CONFIG_BT_HCIUART_ATH3K may not be "m", therfore we cannot inherit the
kmod selection state. Force the "CONFIG_BT_HCIUART_ATH3K" symbol to "y" in
order to avoid `warning: symbol value 'm' invalid for BT_HCIUART_ATH3K` and
subsequent kconfig stalls.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47237
This is another useful gadget driver that can allow an OTG port to act as a
mass storage device.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 47225
Adds the package to select the mvsw61xx module present in the 3.18/4.0/4.1
kernels.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 47224
Since r46834, IPv6 support is builtin if selected. Therefor, dependencies
on kmod-ipv6 can no longer be fulfilled, since it is not a module anymore.
Signed-off-by: Arjen de Korte <arjen+openwrt@de-korte.org>
SVN-Revision: 47022
This patch fix https://lists.openwrt.org/pipermail/openwrt-devel/
2015-August/034979.html. As the peak detect calibration is set
incorrectly.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46948
Thanks to Sylwester Petela for testing my patch (successfully on an
ADSL connection) and for pointing out some configuration mistakes.
Others (including me) have also successfully tested this extensively
on VDSL connections.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46920
DWC2 driver has config symbol CONFIG_USB_DWC2_DEBUG_PERIODIC which
should be defined for the module build.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46916
The driver only supports wl18xx-fw-4.bin and does not support the old
firmware wl18xx-fw-3.bin and more.
The wl18xx-conf.bin file was removed upstream it does not fit all
devices any more, see this on how to generate one:
http://processors.wiki.ti.com/index.php/Open_Source_Wireless_Connectivity_wlconf
If someone has a config file for the common platforms with the wifi nic
OpenWrt uses please send a patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46887
- should fix issue: https://forum.openwrt.org/viewtopic.php?id=57315
- enable support of more USB stick with rt28xx chipsets
- experimental: USB-IDs not in vendor linux driver
- experimental: "exact chipset is unknown"
- experimental: "enabling these devices may or may not work"
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46882
Everything except for blkcipher was already built-in, so make blkcipher
built-in as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46820
Without this patch adding the wifi device to the bridge may fail
because the bridge is not already configured when the wifi device gets
configured. This patch makes broadcom-wl wait till the bridge is ready.
This fixes#17262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46749
So far support for multiple interface was somehow broken in brcmfmac.
Driver couldn't correctly match firmware and system interfaces resulting
in not working APs and WARNINGs. This pending patches fixes that :)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46734
We sill don't use kernel 4.2 which is required for backporting using
upstream NVRAM support patch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46724
The ipw2x00 drivers assume that the system they are running is little
endian, and access everything in native byte order. When run on a big
endian system, everything breaks apart.
Since fixing this is non trivial on a first glance, disable them for
big endian targets.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46708
firmware is not available in linux-firmware yet
so use official driver source
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46682
of_get_gpio_flags() could return an error like EPROBE_DEFER which was
not handled before. This patch takes the code from gpio_keys_polled.c
for error handling and also improves some other unrelated small parts.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46502
This was deactivated in r21954 because it depended on kernel 2.4, but
this module also compiles with kernel 3.18.
This closes#20199.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46495
An #ifdef for the kernel version was missing around the header of
debugfs_create_devm_seqfile() and the LINUX_BACKPORT() was also not
done.
This closes#20181
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46492
Ath debug mode applies to ath10k as well as ath9k.
Update Makefile help text to clarify.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
SVN-Revision: 46468
request_mem_region returns NULL when requesting the region failed, and
a valid pointer when it was successful. Currently the condition is
inverted.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46452
kmod-at86rf230 select REGMAP_SPI since 3.17, so add a dependency to
kmod-regmap.
Fixes the following error:
Package kmod-at86rf230 is missing dependencies for the following libraries:
regmap-core.ko
regmap-spi.ko
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46387
Added option for old firmware version (10.1 API v2). It seems that recent
firmware versions are constantly crashing (at least on a QCA9880-BR4A-R) and
this provides the option to select an older version instead.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46340
Make wpan depend on not kernel 3.18 so it will get activated on all
other kernel versions like 4.0 and 4.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46276
Ath10k has now a proper method of providing calibration data via
the kernel firmware API. This patch can be dropped as all boards
now use the proper method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46245
reorder some parts of the patch to remove the declaration-after-
statement warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46205
Current firmware should work for station mode as well, and the older
firmware will usually behave worse and become unsupported over time.
Also, the MAC address handling on ar71xx is only implemented on one
firmware version.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46197
This firmware adds support for management frames over normal
packet transport interface instead of over the WMI management
interface.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46195
sd_mod depends on scsi_mod, but due to it being an AutoLoad and not
AutoProbe module, it was not loading when installing the package,
causing unknown symbol errors for sd_mod and anything depending on it.
Closes#14927, #18293, #19351.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46176
We were not copying the additional files needed to get USB to work on
the AT91 platforms, make sure we do this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 46172
A long time ago, ath9k had issues during reset where the DMA engine
would stay active and could potentially corrupt memory.
To debug those issues, the driver would print warnings whenever they
occur.
Nowadays, these issues are gone and the primary cause of these messages
is if the MAC is stuck during reset or busy processing a long
transmission. This is fairly harmless, yet these messages continue to
worry users.
To reduce the number of bogus bug reports, turn these messages into
debug messages and count their occurence in the "reset" debugfs file.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46158
A duplicate include guard prevents inclusion of barrier.h in UML build and this prevents mac80211 from building.
This patch re-enables mac80211 hwsim and renames the include guard.
See https://lists.openwrt.org/pipermail/openwrt-devel/2015-June/033614.html for details.
Signed-off-by: Martin Tippmann <martin.tippmann@gmail.com>
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 46133
Boot tested: http://pastebin.com/L6aAb9xj
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo:
update to 4.1 final
add patches added since submission
delete patches applied in later rcs
restore commit messages in 220-gc-sections and 304-mips_disable_fpu
fix 050-backport_netfilter_rtcache to match new API
update inlined dma ops with upstream changes
add missing config symbols
enabled CONFIG_MULTIUSER
update kmod defintions for 4.1
]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46112
There are two important patches in this patchset: updating read pointer
quicker & rework of .get_station().
There are few more upstream patches that are p2p-related and weren't
backported in this commit.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46084
This fixes some build problems with musl. The binary only program
nas.exe wants to link against __assert, which is copied from uClibc.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46021
On bcm53xx we still need usb-ohci to support USB 1.1 devices and it
obviously needs bcma-hcd.ko that will init controller and register
platform device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45994
This one cannot possibly work, as it depends on cfg80211, which is built
out of tree.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45985
This allows e.g. BCM43602 to work out of box, without dumping a proper
MTD partition to /lib/firmware/ NVRAM file.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45931
They are useless, as the platform already selects the right options for
NAND support. The main reason for removing them is the fact that it
makes kernel configs more annoying to maintain on platforms that provide
NAND drivers but disable them (e.g. ramips)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45919
These are two new packet schedulers introduced in Linux 3.12 and 3.14
respectively. sch_fq is a perfect fairness queueing scheduler that also
adds pacing on host TCP flows, and sch_pie is an AQM.
Having them available in kmod-sched makes it easier for people to test
these new queueing schemes.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
SVN-Revision: 45885
We just moved the stmmac support in the kernel for ipq806x. Therefore,
nobody needs this driver so we'll just get rid of it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45872
Add dependency of kmod-crypto-ecb to kmod-bluetooth to avoid the kernel warning
"Bluetooth: Unable to create crypto context".
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 45860
Before starting hostapd we create interface for it. The problem is we
try to create STA interface just to let hostapd change it to AP later.
It may fail if device doesn't support STA interfaces or if we already
hit a limit. Consider following phy (it's from BCM43602 and brcmfmac):
$ iw phy phy0 info | tail
valid interface combinations:
* #{ IBSS, managed } <= 1, #{ AP } <= 4, #{ P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
total <= 3, #channels <= 1
Trying to setup 2 interfaces: STA + AP results in:
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): Configuration file: /var/run/hostapd-phy0.conf
radio0 (1101): Could not read interface wlan0-1 flags: No such device
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45856
nss-gmac has been replaced by its upstream counterpart "stmmac", to
which we added the SoC glue layer required for it to run on IPQ806x.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45832
This fixes various problems with parsing platform NVRAM. It's required
to get BCM43602 working in most cases.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45802
modules relating to CONFIG_USB_AUDIO
Kernel <2.6.35 is not supported in trunk
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45734
3.18.12 backported 61ada528dea028331e99e8ceaed87c683ad25de2 ("sched/wait:
Provide infrastructure to deal with nested blocking") from 3.19, causing
the following error on load:
[ 13.588000] compat: exports duplicate symbol woken_wake_function (owned by kernel)
Fix this by guarding it with a check for 3.18.11 or earlier instead of
3.19.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45710
Before r45593 kmod-l2tp-ip did not depend on kmod-ipv6.
With r45593 support for L2TP IPv6 encapsulation was added and
included in the kmod-l2tp-ip package. This change also
added the dependency to kmod-ipv6 to kmod-l2tp-ip, regardless
of whether the user chose to generally include IPv6 support
or not.
Change this so L2TP over IPv6 and the resulting dependency
to kmod-ipv6 is only included in kmod-l2tp-ip if IPv6 support
is enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45612
instead of failing when authsae is not installed, also try using
wpa_supplicant as the newly added -mesh variants support mesh mode
and SAE encryption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45520
it has been non-functional for years and caused numerous memleaks and
crashes for people that tried to enable it.
it has no maintained upstream source, and it does not look like it's
going to be fixed any time soon
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45423
Two errors "netifd: radio0: sh: bad number" have recently surfaced in system
log in trunk when wifi interfaces come up. I tracked the errors to checking
numerical values of some config options without ensuring that the option has
any value.
The errors I see have apparently been introduced by r45051 (ieee80211r in
hostapd) and r45326 (start_disabled in mac80211). My patches fix two
instances of "bad number", but there may be a third one, as the original
report in bug 19345 pre-dates r45326 and already has two "bad number" errors
for radio0.
https://dev.openwrt.org/ticket/19345
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45379
Fixes build failure caught by buildbot:
IEEE Std 802.15.4 Low-Rate Wireless Personal Area Networks support (IEEE802154) [M/n/y/?] m
6lowpan support over IEEE 802.15.4 (IEEE802154_6LOWPAN) [N/m/?] (NEW) aborted!
Console input/output is redirected. Run 'make oldconfig' to update configuration.
make[6]: *** [silentoldconfig] Error 1
make[5]: *** [silentoldconfig] Error 2
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45357
- move config symbol to separate package (Why was it there in the first place?)
- 8723au might be used in some USB sticks or on some sunxi boards
compile tested only
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45336
Subtarget legacy is supposed to support all ssb SoC except for BCM4705.
There are few BCM4703 devices with 802.11n supprt (WRT160N v1.0, v1.1).
Few BCM4704 devices with 802.11n: ASUS WL-500W, Linksys WRT150N v1.0 &
v1.1, Linksys WRT300N v1.0, Netgear WNDR3300 v1, WNR834B v1 & v2.
It seems we have to enable N-PHY for legacy as well to support above.
Unfortunately it increases root.squashfs size by 48 460 B.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45309
This driver is upstream since 2012 (commit: a8e510f682f), so switch to
it and remove own sources. Also place it under "Network Devices" menu
together with other phy drivers.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 45269
Most AP devices out there do not have a properly programmed regulatory
domain code, which means they are limited to US frequencies by default.
This has been a major annoyance for a long time now. Since no fix for
the manfuacturing process seems to be forthcoming, the only sane option
seems to be to allow users to change the country code in such cases.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45252
Otherwise procd cannot initialize the watchdog since the module will
be loaded later.
Tested with booke_wdt.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 45239
CONFIG_MFD_OMAP_USB_HOST is needed for working USB on BeagleBoard
tested on BeagleBoard C4 (EBVBeagle)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45236
replaces kmod-usb-serial-motorola-phone it's found only in Kernel <3.12
This module handles many simple USB serial devices
like Motorola Phones, GPS reveivers in Kernels above 3.14
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45233
This module is needed for bluetooth audio playback
with pulseaudio 6 and bluez5.
a working guide can be found in the wiki:
http://wiki.openwrt.org/wiki/bluetooth.audio
(additional packages/modifications are required
and submitted to github feeds)
tested with:
Android mobile (Sony Xperia M) as audio source
TI omap BeagleBoard as audio sink
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45231
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
v2: changes in input.mk broke the patch, some of the CONFIG_SND_*
stuff was added already
SVN-Revision: 45205
from upstream
commit title: "[IPV4]: The scheduled removal of multipath cached routing support."
removed in Kernel 2.6.23 (2007)
Reasons: very buggy, no maintainer, no fixes
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45121
driver in staging since 3.14
removed upstream in 3.17
from upstream commit message:
Most webcams covered by this driver are now supported by gspca.
Nobody has the hardware or is willing to convert the remaining devices to gspca.
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45120
This backports upstream commit 702131e2a393b45174be326f1dbe20b658b4f157
bcma: move PCI IRQ control function to host specific code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44969
Based on patch by Bryan Forbes <bryan@reigndropsfall.net>
Also update mt76 to update for API changes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44655
buildbot complained about
ifxmips_ptm_adsl.c:1445:70: error: macro "alloc_netdev" requires 4 arguments, but only 3 given
g_net_dev[i] = alloc_netdev(0, g_net_dev_name[i], ether_setup);
^
fix that similar to the change made to ltq_ptm_vdsl.c
compile tested only.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44632
HAMRADIO enabled in all generic configs, but no one platform directly
use related drivers/protocols. This symbol is only used for kmod-ax25
package modules. Furthermore, half of platforms explicitly disables
this symbol, what silently disables build of modules for kmod-ax25
package.
So disable HAMRADIO by-default in generic config, add it to kmod-ax25
package and remove it from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44613
The initial fix for 3.18 in r44346 wrongly treated the newly added
parameter of alloc_netdev to be another function pointer, causing
ether_config to be skipped during ptm netdev init.
Fix this by partially reverting r44346 and properly setting the newly
added macro parameter.
(Tested on VRX200 board)
A similar change might be needed for ltq-ptm-adsl as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44607
IP VTI (Virtual Tunnel Interface) is used to create a virtual device
for IPsec VPN (similar to OpenVPN).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
SVN-Revision: 44606
This driver is used on IPQ806x to instanciate & drive the ethernet
interfaces.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44521
This patch adds SDIO support for the brcmfmac driver.
For now only very few boards need it.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44465
Kernel commit 1bb5a356c3ea ("net: reduce USB network driver config
options.") hid the USB network drivers behind the new config symbol
CONFIG_USB_NET_DRIVERS.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
SVN-Revision: 44460
Instead of hardcoding /bin/bash, use /usr/bin/env bash - this fixes the
build on FreeBSD 10.1.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44283
The mt76 driver might have some problem working with MT7602.
MT7602 should not have VHT capabilities . But the driver not identity properly.
Signed-off-by: wengbj <fl.service@t-firefly.com>
SVN-Revision: 44257
Part of rev 44173 added setting the SM Power Save capability in the hostapd.conf
file if the driver indicated that it was supported. It appears this was
incorrect, because the field in the actual HT Capabilities field in the AP
configuration is really a state indication. Just copying the state from the
capability resulted in the AP indicating that it had SMPS enabled all the time
if it supported SMPS. This effectively just disables all clients from sending
packets to the AP with more than one spatial stream, for no good reason.
So remove this part of the change.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 44239
This "patch to the patch" fixes a NULL pointer derefence crash in the new
intermediate software queues. The crash can be reproduced by injecting an
802.11 frame with a BSSID that does not belong to a configured vif. The
wperf tool (https://github.com/anyfi/wperf) may be convenient for doing
this.
Signed-off-by: Johan Almbladh <ja@anyfi.net>
SVN-Revision: 44220
This patch adds support for Realtek r8712 and RTL8188SU/RTL8191SU/RTL8192SU
family of fullmac usb wireless cards. The r8712u staging driver only supports
WEXT but works with no problems in OpenWRT.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 44184
Update the libertas driver to configure symlinks in sysfs. This enables
the driver to be handled correctly by the mac80211/netifd/hostapd scripts.
With this patch, the wireless interface is functional on Guruplug Server Plus.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 44174
Add some missing 802.11n capabilities to the hostapd ht_capab string when
supported by the hardware: Spatial Multiplexing Power-Save and 7935-byte AMSDUs.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 44173
If '/sys/class/ieee80211/phyN' is not a symlink, the call to readlink
produces either an empty path (if /sys/class/ieee80211/phyN/device doesn't
exist) or a path that begins with '/sys/class/ieee80211' (which does not
work with the subsequent line to strip '/sys/devices' from the beginning of
the path). Modify the checks to detect these conditions, and fallback to
using the macaddr.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 44172
Change the name of the package to match the module name so it matches the
package name referenced by the Kirkwood (Guruplug) profile.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 44171
Adding support 6LoWPAN over Bluetooth Low Energy in kernel 3.18.
Creating new bluetooth_6lowpan group with CONFIG_6LOWPAN and CONFIG_BT_6LOWPAN.
Adding kernel object dependencies for 6LoWPAN over Bluetooth Low Energy.
Signed-off-by: Lukasz Duda <lukasz.duda@nordicsemi.no>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44084
Add documentation that makes it easier to find the alternative,
recommended, and default handling for buttons in OpenWrt.
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
SVN-Revision: 43989
Target pxcab and ps3 were removed from maintaince in r34764 and r34765
respectively.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 43850
The kernel build system cannot track dependencies of out-of-tree
modules, making the buildsystem fail to load mac80211.
Add mac80211 as an explicit load to ensure all required modules are
loaded.
Fixes#16522.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43631
it should needs to depend on imx and mxs
also remove duplicate kmod definition from mxs target
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43627
This is the oxnas target previously developed at
http://gitorious.org/openwrt-oxnas
Basically, this consolidates the changes and addtionas from
http://github.org/kref/linux-oxnas
into a new OpenWrt hardware target 'oxnas' adding support for
PLX Technology NAS7820/NAS7821/NAS7825/...
formally known as
Oxford Semiconductor OXE810SE/OXE815/OX820/...
For now there are 4 supported boards:
Cloud Engines Pogoplug V3 (without PCIe)
fully supported
Cloud Engines Pogoplug Pro (with PCIe)
fully supported
MitraStar STG-212
aka ZyXEL NSA-212,
aka Medion Akoya P89625 / P89636 / P89626 / P89630,
aka Medion MD 86407 / MD 86805 / MD 86517 / MD 86587
fully supported, see http://wiki.openwrt.org/toh/medion/md86587
Shuttle KD-20
partially supported (S-ATA driver lacks support for 2nd port)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43388
r37490 removed the actual driver but left the kmod definition intact,
causing the build system hapily creating an empty package for it.
Remove it also to not make it seem as if it still exists.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43316
Starting from kernel version 3.15, the crc32c module was renamed to
crc32c_generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43291
usb-common.ko was moved to drivers/usb/common starting from kernel 3.16
by upstream commit f4cbd33fd5f0587910fa9db403a1b42f1cabf820
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43290
This patch adds the userspace and kernelspace for
- match NETFILTER_XT_MATCH_CLUSTER
This match can be used to deploy gateway and back-end load-sharing clusters.
- target IP_NF_TARGET_CLUSTERIP
This module allows you to configure a simple cluster of nodes
that share a certain IP and MAC address
without an explicit load balancer in front of them.
Connections are statically distributed between the nodes in this cluster.
This is used i.e. by strongswan-ha.
Signed-off-by: Christian Scheele <cs@embedd.com>
SVN-Revision: 43174
Only list the kernel versions that do not match so that new kernel
versions will automatically match. This improves support for kernel
3.18.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43132
This patch added stuff that is already there and if it would be needed
this would result in a compile error.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43131
More recent kernel versions (>= 3.12) support native VXLAN
support.
The Open VSwitch kernel module tries to build using native VXLAN
support if it detects a kernel version >=3.12.
The build works fine, but during startup the OVS kernel module
does not load.
dmesg output is something like this:
[ 1201.262842] openvswitch: Unknown symbol vxlan_sock_release
[ 1201.262949] openvswitch: Unknown symbol vxlan_xmit_skb
[ 1201.263161] openvswitch: Unknown symbol vxlan_sock_add
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 43126
Using a redirect to a non-empty mtd partition will not erase the
blocks prior to writing to them resulting in broken dsl_fw.
Fix this by piping to mtd write - /dev/mtdX instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43125
The DHT11 is a temperature and humidity sensor supported by linux
since 3.14.
This patch is tested on recent mxs with kernel 3.14.18.
Signed-off-by: Harald Geyer <harald@ccbib.org>
SVN-Revision: 43103
- Support HT40 instead of HT40+/HT40- like mac80211
- Enable 11n if htmode is HT20 or HT40
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43063
Attempting to build broadcom_wl (from trunk) with the linaro 4.9.x
toolchain produces the following errors:
<...>/wl_linux.c: In function 'wl_dump_ver':
<...>/wl_linux.c:2302:3: error: macro "__DATE__" might prevent reproducible builds [-Werror=date-time]
__DATE__, __TIME__, EPI_VERSION_STR);
^
<...>/wl_linux.c:2302:13: error: macro "__TIME__" might prevent reproducible builds [-Werror=date-time]
__DATE__, __TIME__, EPI_VERSION_STR);
^
cc1: some warnings being treated as errors
Remove the use of the __DATE__ and __TIME__ macros, as the info is not
really useful.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 43046
This module is required to read the CPU core temperature sensors
on the Alix APU board.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43027
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
