At the moment the padding steps are hardcoded. Especially images for
devices with a 4K sector size can be unnecessarily bloated using the
hardcoded padding steps.
It has been observed that 192Kb of padding was added to the image of a
4MB device, albeit due to the 4K sector size the minimum required extra
padding for the jffs2 rootfs_data is 20Kb.
In worst case it means that the image-size check could fail albeit
there is enough space for all selected packages
For device build code not exposing the blocksize, use the hardcoded
padding further on.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Allows to use the same unit for all definitions of the blocksize to be
consistent regardless of the used filesystem.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Some devices (e.g. Tenda AC9 based on BCM47189B0) have BCM53125 with
port 5 connected to the second Ethernet interface on the SoC. In such
case there is no PHY and we need to force link manually.
This assumes port 5 can be marked as enabled for such devices. It's not
implemented yet unfortunately.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Don't expose dnsmasq version & other data to clients via the *.bind
pseudo domain. This uses a new 'NO_ID' compile time option which has been
discussed and submitted upstream.
This is an alternate to replacing version with 'unknown' which affects
the version reported to syslog and 'dnsmasq --version'
Run time tested with & without NO_ID on Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
e2fsprogs would fail linking with external toolchains which would not be able
to find several dependencies, explicit them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The insertion or removal of the sd-card cannot be detected
by the hardware itself. This is by design. To workaround this,
for the WNDR4700 unload/load the dwc2 module in case the
the special SD CARD GPIO line is low/high.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
A few linux BSP's create a manifest file of installed packages for a given
target in order to help them understand exactly what's on their images. Create
one here as well as a build artifact since many users have an affinity to
prune down on packages to save valuable flash space.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
First two patches weren't marked for stable but are dependencies for
laters ones. The rest of patches was marked for stable but most likely
will be backported to 4.5+ only so we need to get them on our own.
An important fix is eea2fb4851e9d ("ovl: proper cleanup of workdir") as
it allows mounting overlayfs with dirty workdir, e.g. after power cut.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
If the toolchain is packaged for later use as external toolchain, the resulting
tarball is created in $BIN_DIR. But without building all packages first that
directory isn't created, hence 'make target/toolchain/compile' fails when
trying to create the toolchain tarball with error "Cannot open: No such file or
directory".
To fix that the $BIN_DIR is created before using it.
Signed-off-by: Micha Lenk <micha@lenk.info>
Regression introduced by 3481d0d dnsmasq: run as dedicated UID/GID
dnsmasq is unable to remove its own pidfile as /var/run/dnsmasq is owned
by root and now dnsmasq runs as dnsmasq:dnsmasq. Change directory
ownership to match.
dnsmasq initially starts as root, creates the pidfile, then drops to
requested non-root user. Until this fix dnsmasq had insufficient
privilege to remove its own pidfile.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Add a dependency on DRIVER_11W_SUPPORT in order to enable the IEEE
802.11w functionality in hostapd.
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
Russell Senior reported an issue with the MR24 initramfs kernels:
> ## Booting kernel from Legacy Image at 00c10000 ...
> Image Name: POWERPC LEDE Linux-4.4.19
> Created: 2016-08-31 11:57:05 UTC
> Image Type: PowerPC Linux Kernel Image (gzip compressed)
> Data Size: 2155723 Bytes = 2.1 MiB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
>Wrong Ramdisk Image Format
>Ramdisk image is corrupt or invalid
For the MR24, the kernel is uploaded to 0x10000. The ramdisk starts
at 0x200000. This leaves the kernel with just 0x1f0000 bytes = 1984kb.
This patch adds a size check so the image creation script will abort
instead of producing a unbootable initramfs image. A separate patch
"apm821xx: Fix initramfs image for the Meraki MR24" which fixed the
reported issue was submitted earlier.
Cc: Russell Senior <russell@personaltelco.net>
Cc: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When gzip is used, our kernel is too large and this causes the ramdisk
to be at the wrong offset. Fix by moving to lzma.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
oneshot trigger configurations for LEDs are created, but the on/off
timing configurations are ignored. generate_config is correctly creating
oneshot configs, but the later led script doesn't recognise the trigger
details.
Fixes: c0c3f2d4c9 leds: support oneshot as well as timer triggers
Signed-off-by: Karl Palsson <karlp@etactica.com>
Enable CONFIG_PROCD_ZRAM_TMPFS compatibility via two changes to list_cpu_idx():
* detect if /tmp is being used by /dev/zram0; if yes, offset initial value by 1 to skip first zram device.
* hot-add /dev/zram1, if not already present.
Signed-off-by: Conn O'Griofa >connogriofa@gmail.com>
Add a patch to backport 5185c91385d73cdf79836eb8548e4726e43ae831
from Linux 4.8 adding USB2380 support to the NET2280 driver and
create an OpenWrt menu option to select it as a module.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks Ventana GW553x is a single-board computer based on the NXP
IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* small form factor (35x70mm)
* 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
* 256MB NAND flash (4GB option)
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* 1x miniPCI socket (with PCIe, USB, SIM)
* 1x microSD socket
* 1x SIM socket
* Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
* analog CVBS video in
* GPS (optional uBlox EVA-M8M)
* Application headers:
- 2x TTL UART (TX/RX)
- 4x TTL GPIO (3x configurable as PWM)
- 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
* Front panel connectors:
* micro-HDMI audio/video out
- 1x user programmable LED
- 1x configurable user pushbutton
- 1x USB OTG
See http://www.gateworks.com for more info
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
