The QorIQ FRDM-LS1012A Board is an ultra-low-cost
development platform for QorIQ LS1012A Series Network
Processors built on ARM Cortex-A53 processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add PPA (The Primary Protected Application)
package and also enable it for all layerscape devices.
LSDK github provides ppa source code git tree, but it
only could be compiled with 64-bit toolchain. For 32-bit
devices, there was no method to use it.
https://github.com/qoriq-open-source/ppa-generic
This patch is to directly use a private ppa binary tree for
both 32-bit and 64-bit devices.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to use ppfe git tree on LSDK github
instead of private git tree, and support the latest
ppfe on ls1012ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Some new options were introduced by kernel patches.
And some options should be removed/added.
The config-4.9 should be updated accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Updated kernel patches to align layerscape kernel
with latest LSDK linux (LSDK-17.09-update-103017-V4.9 tag).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Default profile had to enable many packages for all devices
support. This made these packages still enabled when built
for single device. This patch is to remove default profile.
For multiple devices build, it's proper to build with multiple
devices profile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
A previous patch disaggregated kernel patch 601 intending to
reverse the ndo_get_stats64 change, but it also dropped
many other changes without a reason. This caused build issue
for layerscape. This patch is to fix that with below steps.
1. Reversed patch "1c4415a layerscape: reverse changes to ndo_get_stats64",
but kept kernel patch 701 which was a proper fix.
2. Reversed the ndo_get_stats64 change in kernel patch 601.
3. Renamed patch 601 (net patch) to 202 (core-linux patch). Maybe it's
more proper.
Fixes: 1c4415a679 ("layerscape: reverse changes to ndo_get_stats64")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
On the Asus RT-N16, the ports are not mapped the in the same way as
the RT-N12. It is, however, the same as the Linksys E3000v1.
Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
The memcpy of the init data relies on chip->registers to be initialized,
which only happens later in the code. Move this initialization further
down to make it work.
This was breaking PCIe/USB on some MikroTik RouterBoard devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MAC addresses were not being set for LAN and WAN. This will now use the
same MAC mechanism as the rest of the target.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and
non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 1x LED (GPIO-controlled), 1x button
* LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Orange LED is registered so you can later use it for your own purposes.
Flash instruction:
Unlike TL-WR840N v4 flashing through WEB UI works in v5.
1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image.
2. Go to 192.168.0.1
3. Flash the sysupgrade image through Firmware upgrade section of WEB UI.
4. Wait until green LED stops flashing and use the router.
Notes:
TFTP recovery is broken since TP-Link reused bootloader code for v4 and
that does not take into account only 4 MB of flash and bricks the device.
So do not use TFTP Recovery or you will have to rewrite SPI flash.
They fixed it in later GPL code,but it is unknown which version of
bootloader you have.
After manually compiling and flashing bootloader from GPL sources TFTP
recovery works properly.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The splitter ignored the rootfs offset from the header, probably
because until c1e6e61 it was invalid.
This patch fixes the splitter to use the now correct header data.
Regarding target/linux/ar71xx/files/drivers/mtd/tplinkpart.c,
this particular splitter "falls back" to the correct rootfs offset
reading and as such it doesn't need to be updated, although it will
report a kernel partition length that can be larger than the actual
length as it assumes that partition fills the entire segment up to
the rootfs partition.
Tested-by: Mathias Kresin <dev@kresin.me>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Tested-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
- H3 @ 1.3 GHz
- 1GiB DDR3
- 10/100Mbps Ethernet
- Realtek RTL8189ETV wifi
- 4 USB 2.0
Difference to the "Orange Pi Plus" is the lack of Gbit ethernet
and lack of onboard flash.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Current jumbo frame support code allocates rxbuffers of the maximum size
supported by the hardware (~14KB). This happens at the device open time
even if the configured MTU is lower (e.g. if it configured to standard
1500 bytes). Such behavior effectivly prevents interface start on boards
with a low ammount of RAM (e.g. WRT300N v2), since the kernel simly can
not allocates of ~0.8MB (14KB x 64).
So remove jumbo frame support for now.
Reported-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Tested-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
The patch, which adds multiphy support, adds new path for non-standard
PHYs (e.g. MV88E6060 switch IC) to avoid using kernel phy framework. All
work well except the link status traking (Duplex and Speed), which is
reseted as soon as PHY connection procedure is done. This leads to lost
of the link status of non-standard PHY, which is configured exactly in
the ixp4xx_phy_connect() function.
Move the generic reset of a link state to the ixp4xx_phy_connect()
function to the code path, which is intended for handling of a normal
PHY.
Reported-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Tested-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
The MarsBoard was a short-lived credit-card sized, extendable board with an Allwinner A10 SoC.
http://linux-sunxi.org/MarsBoard_A10
Signed-off-by: Kayo Phoenix <kayo@illumium.org>
[Forward-ported to new target layout:]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
On NOR based Mikrotik devices, 4K sectors significantly slow down
firmware flashing and jffs2 usage. On NAND based devices they may be
necessary to run rbcfg (the boot loader config is often on SPI NOR).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some targets need 4K sectors for small flash chips (e.g. some
routerboards, where the entire chip is just one "erase block"), whereas
on other devices 4K sectors lead to horrible flash erase/write
performance.
Set the default limit in the generic kernel configuration to 4 MiB to
ensure that all new platforms don't use 4K sectors for bigger flash
chips. On all existing targets use 16 MiB for now to avoid regressions.
They will be changed individually in follow-up commits.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This changes the cmdline from:
Kernel command line: root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
to
Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p5
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
As a consequence booting from the alternative dual-boot partition set
(root=/dev/mmcblk0p8) becomes possible.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)
First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize
Further upgrades via sysupgrade.
Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition
Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.
Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.
Changes since v2:
- based on dts(i) rework/cleanup submitted:
http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Supported frequencies of all ipq40xx chips are 48, 200, 500 and 716.8 MHz.
Previous 666MHz setting was most likely related to instability of early
chips/boards made before mass production.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
This fixes the LED configuration for the D-Link DIR-869 A1. In order to
support the device I probed around using an initramfs image for the
UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them.
GPIO 16 set to low meant that the color was white while pulling it to high
made the color change to orange. The past code was written based upon these
findings.
However, running a flashed image I now discovered that GPIO 15 controls the
orange LEDs while GPIO 16 controls the white ones and that both are active
when low. This means that the GPIOs were inverted and one active_low was set
wrong which this patch fixes.
Behavior of the LED front after this patch is applied:
cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness
0 -> white LEDs are OFF
255 -> white LEDs are ON
cat /sys/devices/platform/leds-gpio/leds/d-link🍊status/brightness
0 -> orange LEDs are OFF
255 -> orange LEDs are ON
If the brightness of both is set to 255 the LED front will be white.
If the brightness of both is set to 0 the LED front will be off.
Signed-off-by: Florian Beier <beier.florian@gmail.com>
The GPIOs are used for defined LEDs and therefore are ignored/unset in
the ath9k driver since 192f0a3db8. The wireless led led trigger is
added in userspace since e20965811d, which makes the
ap9x_pci_setup_wmac_led_pin() superfluous.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The platform data was missing the num_registers element which is now
mandatory in linux 4.9
Without this patch, the gpio probing would fail with:
gpio gpiochip1: (74x164): tried to insert a GPIO chip with zero lines
Fixes: #1106
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr
value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses
are stored in the ART partition and the generated MAC addresses for the
wlan interfaces alternate randomly between 12:34:56:78:90:12 and
00:03:7f:12:34:56.
interface new/ OEM MAC old MAC
wlan-2.4g (phy1): ethaddr undefined
wlan-5g (phy0): ethaddr + 1 undefined
lan : ethaddr + 2 ethaddr
wan : ethaddr + 3 ethaddr + 1
This patch defines stable MAC addresses for the wlan interfaces for
the first time instead of generating them at random. The previously
defined values for lan/ wan are changed to follow the settings of the
OEM firmware.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split
into the readonly squashfs and ext4 for the overlay. This adds the
required package to the device packages to allow mounting the overlay
by default.
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect)
Before this commit, the ext4 based overlayfs could not be mounted,
which left only the tmpfs based/ volatile emergency overlay in place.
Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
On some devices the flash chip needs to be in 3-byte addressing mode during
reboot, otherwise the boot loader will fail to start.
This mode however does not allow regular reads/writes onto the upper 16M
half. W25Q256 has separate read commands for reading from >16M, however
it does not have any separate write commands.
This patch changes the code to leave the chip in 3-byte mode most of the
time and only switch during erase/write cycles that go to >16M
addresses.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Serial output was broken since 3.16 for shared uarts between
kernel and login. Fix this by adding a fix sent upstream.
While at it, drop a useless patch that adds duplicate code.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The NXP LSDK kernel backported changes for interface ndo_get_stats64
functions from mainline, this causes a compile error with
backports/mac80211, which expects the original 4.9 defintion.
As reversing the ndo_get_stats64 change signifcantly reduces the size of
patch 601, the patches that were aggregated into it have been
disaggregated.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
These conflict with the kmod packages (such as nf-netlink)
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Add same changes for arm8_32b subtarget and refresh config]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mark target arc770 as source-only as it has package compile issues
(e.g. iproute2) due to the usage of uClibc.
As a prerequisite to be included in future releases the arc770 target
needs to switch either to glibc or musl.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
