Commit graph

809 commits

Author SHA1 Message Date
Henryk Heisig
1b2b3cb8be ar71xx: wpa8630: change board name to tl-wpa8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
8cc0c34ef5 ar71xx: Add support to Powerline ac TP-Link WPA8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 17:13:37 +01:00
Chris Blake
53b43e65e7 ar71xx: Add net config for MR12 & MR16
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-10-31 12:52:56 +01:00
Stijn Tintel
e3875350f3 ar71xx: add support for D-Link DAP-2695 rev. A1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Stijn Tintel
e19427bd79 ar71xx/base-files: rename 09_fix-trx-header 09_fix-checksum
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Julius Schulz-Zander
a71a8955f2 ar71xx: add support for TP-Link WR802N v1
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.

Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
2016-10-26 12:37:45 +02:00
Chris Blake
fac018b25e ar71xx: Remove switch config for the MR12/MR16
These boards do not have a switch, so they should have never been added
to this file in the first place.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:45 +02:00
Jing Lin
7ba9a3a504 ar71xx: Add support to DomyWifi DW33D
Signed-off-by: Jing Lin <mumuqz@163.com>
2016-10-25 17:51:08 +02:00
Henryk Heisig
f5aa459043 ar71xx: Add support to TP-Link EAP120
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-18 09:18:55 +02:00
Christian Lamparter
098f7156cc ar71xx: add support for the Airtight C-60
This patch adds support for the Airtight C-60.

SOC:	Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM:	128 MiB
NOR:	MX25L3205D 4MiB
NAND:	ST Micro NAND 32MiB 3,3V 8-bit
SW-NET:	AR8327N (2 Ports)
WLAN1:	Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2:	Dual-Band AR9300 Rev:4 PCIe Chip

The switch is setup for an accesspoint:
	LAN1: (gigabit) is the wan-port.
	LAN2: (fast ethernet) is bridged with the br-lan.

Flashing Guide (via initramfs):
  1. Connect a PC to the serial port of the C-60.
     power up the C-60.

     Enter u-boot command prompt:
     #> nand erase
     #> setenv bootcmd "bootm 0x9f060000"
     #> saveenv
     #> setenv ipaddr 192.168.1.1
     #> setenv netmask 255.255.255.0
     #> setenv serverip 192.168.1.100
     #> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
     #> tftpboot
     #> bootm

  2. Wait for the C-60 to boot LEDE.
     On the root prompt. Enter:
     # ubiformat /dev/mtd4
     # ubiattach -p /dev/mtd4

  3. After that copy the sysupgrade.tar onto the router and run:
     # sysupgrade sysupgrade.tar

     to flash the image.

Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-10-15 11:36:50 +02:00
Florian Beier
5abeba3450
ar71xx: add userspace support for D-Link DIR-869 A1, generate images
Signed-off-by: Florian Beier <beier.florian@gmail.com>
[Matthias Schiffer: fix factory image, improve commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 22:58:37 +02:00
Matthias Schiffer
e407f1a4c8
ar71xx: add back SEAMA header checksum fix (as used on ramips)
The D-Link DIR-869 A1 doesn't accept images with the jffs2 marker added
after the checksummed range, so we need to include it in the checksum and
fix it on first boot.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 20:57:59 +02:00
Piotr Dymacz
c166b050fd ar71xx: base-files: fix boards order in lib/upgrade/platform.sh
Keep also case sections in alphabetical order.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
8be47007a9 ar71xx: base-files: cleanups in lib/upgrade/platform.sh
This includes:

- code style fixes
- fix boards order within case sections

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
6e58440fc1 ar71xx: base-files: cleanups in etc/board.d/01_leds
This includes:

- use of local 'board' variable in LED names, wherever possible
- merge of boards with exactly the same LED configuration

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
c142df3094 ar71xx: fix LED names for GL Innovations boards
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
8689078a9b ar71xx: base-files: fix code style in etc/board.d/01_leds
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
d09f4e0631 ar71xx: base-files: combine boards with the same config in etc/diag.sh
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
2917ae91ec ar71xx: base-files: cleanups in etc/diag.sh
This includes:

- code style fixes
- use of local 'board' variable in LED names, wherever possible

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
edcdb93467 ar71xx: base-files: fix boards order in etc/board.d/02_network
Keep everything in alphabetical order. Boards are ordered in two steps,
first within/inside common configuration (case section), then sections,
globally.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
a75cfac1f6 ar71xx: base-files: cleanups in etc/board.d/02_network
This includes:

- code style fixes
- removal of huge comment (it should be in doc, not here) and some small ones
- removal of redundant config for DR531/WPJ531 as the default is the same
- merge of boards with exactly the same interfaces config

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
4fa90c49c1 ar71xx: base-files: rework etc/board.d/02_network
Convert etc/board.d/02_network in ar71xx target to the same shape
as we have in ramips target. Split code into two new functions:

- interface/s setup in ar71xx_setup_interfaces()
- MAC/s setup in ar71xx_setup_macs()

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:48 +02:00
Martin Blumenstingl
e7be0decf6 ar71xx: Do not use a hardcoded ath10k firmware mac address
ar71xx has an init-script for special devices where the ath10k OTP
calibration data is stored on the PCIe card's EEPROM (and thus can only
be read by ath10k). Unfortunately the OTP data uses the default mac
address (= all devices come with the same mac address, which leads to
problems when you have multiple of these devices in the same network).

To work around this the mac address is patched in the firmware during
the first boot of the device. To prevent flash wear this was only done
if the ath10k firmware matched a hardcoded md5sum.
However, if the md5sum does not match this can mean that either the mac
address was already patched (which is fine) - unfortunately it can also
mean that the firmware version was updated without updating the
hardcoded md5sum.

Change the "was the mac address already patched" check to actually
compare the mac address inside the ath10k firmware.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-09-28 08:39:01 +02:00
Chris Blake
68d649f5cd ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker Gateway
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-09-27 17:50:22 +02:00
Neal Oakey
524d4110f9
ar71xx: add model detection for many Ubiquiti AirMax XM devices
Signed-off-by: Neal Oakey <neal.oakey@bingo-ev.de>
[Matthias Schiffer: minor adjustments]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-24 19:07:27 +02:00
Jo-Philipp Wich
1c09849f6c treewide: remove bad local shell variable declarations
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-09-24 14:38:20 +02:00
Mathias Kresin
c1578d4fc9 cleanup ucidef_set_interface* usage
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:32:25 +02:00
Piotr Dymacz
f478fba663 ar71xx: add support for Zbtlink ZBT-WE1526
Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2.
Short specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- two external, non-detachable antennas
- 8x LED, 1x button
- UART header (pinout: VCC, RX, TX, GND)

Flash instruction:

Use sysupgrade in vendor firmare which is based on OpenWrt.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-08-18 09:49:18 +02:00
Chuanhong Guo
d1b20a3659 ar71xx: fix profile name of Mercury MW4530R
The mw4530r-v1 profile in tp-link.mk is for Mercury MW4530R.
There is no such a device called TL-WDR4530.
Also change MERCURY to Mercury in /lib/ar71xx.sh

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-08-15 15:18:35 +02:00
diizzyy
1bcad76395 ar71xx: Make wget2nand look for LEDE project firmware files
Make wget2nand aware of the new file names

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2016-07-26 08:39:36 +02:00
Matthias Schiffer
adbbfb7ff9
ar71xx: don't use D-Link DIR-505 status LED as ethernet indicator
The stock firmware uses the single LED as status indicator only. Using the
same LED both for status and as ethernet indicator is uncommon, and has
been confusing users who were using the device as a WLAN mesh node (so the
LED was just off, as no ethernet was connected).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-07-28 15:59:04 +02:00
Matthias Schiffer
500a67a167
ar71xx: add revision detection for D-Link DIR-505 A1/A2
The A1 image also works on the A2, correctly set AR71XX_MODEL in this case.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-07-28 15:44:52 +02:00
John Crispin
96fa9aa13b ar71xx: add a missing ;; to ar71xx.sh
commit 42305ae24a ("ar71xx: add support for gl-mifi")

was missing a ;; breaking boot up

Signed-off-by: John Crispin <john@phrozen.org>
2016-07-24 11:17:34 +02:00
Zhao Gang
42305ae24a ar71xx: add support for gl-mifi
This add initial support for gl-mifi.
Product page: http://www.gl-inet.com/mifi/

Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
2016-07-24 06:38:30 +02:00
Jo-Philipp Wich
e633a1b48f ar71xx: fix default network config of WZR-HP-G300NH and CR3000
The network defaults for the WZR-HP-G300NH and CR3000 models wrongly set the
lan interface to a vlan tagged device while the switch was set up in untagged
mode, leading to broken lan side ethernet connectivity by default.

Fix the issue by emitting untagged interfaces, consistent with the switch
setting on the device.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-20 00:21:48 +02:00
Zhao Gang
d963ddf042 ar71xx: add support for gl-ar300m
This add initial support for gl-ar300m router.
Product page: http://www.gl-inet.com/ar300m/

Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
2016-07-20 00:21:48 +02:00
Piotr Dymacz
d2c9b169b3 ar71xx: add support for jjPlus JWAP230
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers

Default configuration:

- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space

Flash instruction (do it under U-Boot, using RS232):

1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Piotr Dymacz
e767980eb8 ar71xx: add support for Wallys DR531
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers

Default configuration:

- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Yousong Zhou
09907170dd ar71xx: base-files: remove the now unneeded 09_fix-seama-header
It was intended as a workaround when jffs2 eof mark was included in the
checksum calculation in seama header.  When qihoo-c301 support was
introduced the board name was not inserted into the case list (because I
was not aware of it's existence), but the issue was fixed by excluding
the jffs2 marker as part of the checksum data

Now we are at it, drop it.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2016-07-11 13:26:36 +02:00
David Pinilla Caparrós
bbbe9932e3 ar71xx: WDR4300: Fixed default VLAN order
Reordered the VLANs so the LAN ports are set to VLAN 1 and the WAN port is set to VLAN 2, as in the other routers in the config file. Moreover, this model had this VLAN mapping in OpenWRT Chaos Calmer. It seems that the VLAN were switched when fixing a bug in the port mapping ( OpenWRT changeset 47799 )

Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
2016-06-17 04:13:07 +02:00
Allan Nick Pedrana
e61fe4e4d7 ar71xx: add support for OpenEmbed SOM9331
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.

Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
2016-06-07 11:21:55 +02:00
KeLei Liang
563e9d5e1b ar71xx: add WRTnode2Q support
Signed-off-by: KeLei Liang <xzmu@wrtnode.com>
2016-06-06 14:58:11 +02:00
Stijn Segers
d2a91f9853
ar71xx: Fix TL-WR841N v11 LEDs, use separate machine
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-05-31 17:36:51 +02:00
Cezary Jackiewicz
71e0ef3978 ar71xx: add GPIO pin for usb power switch for RouterBOARD 912
RB912 has one usb shared between external USB and miniPCIe slot. GPIO52 can
reroute power to external USB (=1) or internal miniPCIe slot (=0)

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-27 10:27:44 +02:00
Alexander Couzens
c5ff273d85 ar71xx/cpe510: split profile into 2 profiles cpe210 and cpe510
Split profile into 2GHz and 5GHz. The 5GHz devices are
quite "special". The 2 GHz works perfect.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-23 13:39:49 +02:00
Sven Eckelmann
c4e3706533 ar71xx: extract ath10k wifi board.bin for the OpenMesh MR1750v2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:26 +02:00
Sven Eckelmann
77cb985022 ar71xx: enable sysupgrade for the OpenMesh MR1750v2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:25 +02:00
Sven Eckelmann
58dc285cd6 ar71xx: add user-space support for the OpenMesh MR1750v2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:25 +02:00
Sven Eckelmann
222dfb3d6a ar71xx: enable sysupgrade for the OpenMesh OM2P-HSv3
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:24 +02:00
Sven Eckelmann
e10d12411c ar71xx: add user-space support for the OpenMesh OM2P-HSv3
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:23 +02:00
Sven Eckelmann
823cea2d5d ar71xx: Allow OpenMesh CE images with more than 3 files
The CE image format used by OpenMesh can contain extra blocks which
are not used for flashing. Only the first three embedded images
(fwupgrade.cfg, kernel, rootfs) are required in this order to successfully
flash an image via sysupgrade. All extra embedded images should be ignored
for the available devices.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:23 +02:00
Sven Eckelmann
d1b4a8cfcf ar71xx: Move OpenMesh image target validation into subfunction
The platform_check_image_openmesh function used break statements to signal
that the board name matched the image target. This worked because the
sysupgrade binary checked the image inside a loop. The break statement
stopped the loop and skipped any additional check.

Instead the check should be done without such sideeffects by simply
combining the board names and image targets. Only a mismatch should cause a
negative result for the caller and skipping of the additional checks.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:23 +02:00
Cezary Jackiewicz
0b45bec22c
ar71xx: add support for TP-LINK TL-WR842N/ND v3
- CPU QCA9531-BL3A
- RAM: 64MB
- flash: 16MB
- USB

AP143 platform, similar to tl-wr841n v10/v11, but with USB

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-14 21:45:16 +02:00
P.Wassi
8307c2fe68 ar71xx: Add support for Ubiquiti UniFi AP AC PRO
Add support for the Ubiquiti UniFi AP AC PRO
Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
P.Wassi
c855e70491 ar71xx: Rename unifiac to unifiac-lite
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.

Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
blogic
75629fb2a8 ar71xx: add TP-Link TL-WR810N support
This patch adds support for the TP-Link TL-WR810N.
https://wiki.openwrt.org/toh/tp-link/tl-wr810n

Signed-off-by: Jens Steinhauser <jens.steinhauser@gmail.com>

SVN-Revision: 49286
2016-05-10 10:43:12 +02:00
John Crispin
dc92917409 image / basefiles: make console password configurable
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
Signed-off-by: John Crispin <john@phrozen.org>
2016-04-18 21:53:07 +02:00
John Crispin
ee53a240ac ar71xx: Add support for the OMYlink OMY-G1
https://wiki.openwrt.org/toh/omylink/omy-g1

http://www.omylink.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49258
2016-04-26 11:44:36 +00:00
John Crispin
5f1a82ec4f ar71xx: add TP-Link TL-WA901ND-v4 support
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>

SVN-Revision: 49158
2016-04-09 10:26:46 +00:00
John Crispin
d9799dea89 ar71xx: add support for Compex WPJ342
OpenWrt can be flashed with following uboot commands:

tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 49157
2016-04-09 10:26:41 +00:00
John Crispin
063a6499db ar71xx: extract ath10k wifi board.bin for the OpenMesh OM5P-ACv2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49154
2016-04-09 10:26:31 +00:00
John Crispin
3dabaef6a1 ar71xx: enable sysupgrade for the OpenMesh OM5P-ACv2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49151
2016-04-09 10:26:22 +00:00
John Crispin
7461604bd9 ar71xx: add user-space support for the OpenMesh OM5P-ACv2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49150
2016-04-09 10:26:18 +00:00
John Crispin
0c0dc3b2bf ar71xx: extract ath10k wifi board.bin for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49147
2016-04-09 10:26:08 +00:00
John Crispin
0ae22974eb ar71xx: enable sysupgrade for the OpenMesh OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49144
2016-04-09 10:25:57 +00:00
John Crispin
2fa2d97ae2 ar71xx: add user-space support for the OpenMesh OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49142
2016-04-09 10:25:51 +00:00
John Crispin
3c91d5a479 ar71xx: fix the revision of a few TP-LINK devices in AR71XX_MODEL to match labels/image names
Let's not confuse users about the revisions of their devices when we can
easily avoid it.

Not tested on real hardware.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 49107
2016-04-01 07:12:00 +00:00
John Crispin
85c540b94e ar71xx: avoid AR71XX_MODEL ending with a space on some TP-LINK-like devices
Instead of adding the space when combining $model and $hwver, add the space
to the beginning of $hwver, so the resulting string won't end with a space
when $hwver is set to the empty string.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 49106
2016-04-01 07:11:56 +00:00
John Crispin
dfed41d3d8 ar71xx: check both HWID and HWREV on upgrades of TP-LINK devices
There's no reason for us to be more lenient than the stock firmware, so
better check the HWREV as well to avoid bricked devices.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 49105
2016-04-01 07:11:53 +00:00
John Crispin
ba2d1ccffa ar71xx: WNR2200: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2200 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49101
2016-04-01 07:11:34 +00:00
Luka Perkov
8258f8edb6 ar71xx: cosmetic fix of alfa ap120c/ap96 ordering
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49086
2016-03-24 21:09:34 +00:00
Luka Perkov
ebaba15331 ar71xx: add support for ap120c
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49082
2016-03-23 22:31:38 +00:00
John Crispin
5b2d89f060 ar71xx: WNR1000v2: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR1000v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49076
2016-03-23 12:52:35 +00:00
John Crispin
3fd98db818 ar71xx: Add support for the OMYlink OMY-X1
This patch adds support for the OMYlink OMY-X1

https://wiki.openwrt.org/toh/omylink/omy-x1

http://www.omylink.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49026
2016-03-16 09:26:58 +00:00
John Crispin
346b1905fb ar71xx: add support for the Telldus TellStick ZNet Lite
Signed-off-by: Micke Prag <micke.prag@telldus.se>

SVN-Revision: 48977
2016-03-10 19:07:26 +00:00
Felix Fietkau
3f971c0dc8 ar71xx: WNR612v2: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48924
2016-03-05 09:45:15 +00:00
Felix Fietkau
94b8a6b5cf ar71xx: WNR2000v3: add speed_mask to Ethernet port LED initialization
This patch add speed_mask parameter to Ethernet port LED initialization
during system startup. LEDs are configured to show amber light for 10 Mbps
link and green for 100 Mbps as described on device label.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48923
2016-03-05 09:45:10 +00:00
Felix Fietkau
53b3872ddf ar71xx: WNR2000v3: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48922
2016-03-05 09:45:06 +00:00
John Crispin
fbb2449953 AP121 target: fix board detection in ar71xx.sh
Signed-off-by: Attila Lendvai <attila@lendvai.name>

SVN-Revision: 48916
2016-03-04 08:33:38 +00:00
John Crispin
cede06cebc ar71xx: Support for Ubiquiti UniFi AP AC LITE
Add support for the Ubiquiti UniFi AP AC LITE
Signed-off-by: P.Wassi <p.wassi at gmx.at>

SVN-Revision: 48711
2016-02-12 08:31:32 +00:00
John Crispin
d6cb792d21 ar71xx: Added support for TL-WA801NDv3
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>

SVN-Revision: 48705
2016-02-12 08:30:28 +00:00
John Crispin
9df952742d ar71xx: board.d: fix switch defaults on dLAN pro 1200+ WiFi ac
transparent for vlans as originally committed

Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 48358
2016-01-19 10:16:20 +00:00
John Crispin
ed72c5f846 ar71xx: add support for Netgear WPN824N
Add support for Netgear WPN824N.
Hardware specs:
  * AR7240, 4 LAN ports, 1 WAN port
  * AR9285 WLAN
  * 32 MB RAM
  * 4 MB Flash
  * 16 LEDs (LAN, WAN and Power/Status contain two LEDs for dual color
    effect)
  * 3 Buttons (not supported)

Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 48356
2016-01-19 10:16:04 +00:00
Felix Fietkau
826cfa5773 ar71xx: fix ap152 support
- ethernet gigabit pll
- switch configuration
- sysupgrade

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 48187
2016-01-10 17:19:34 +00:00
Felix Fietkau
0da9da0d33 ar71xx: another fix to wndr3700_board_detect
My last bugfix (r47538) introduced a new bug in wndr3700_board_detect
(again...).

Assigning the result of ar71xx_get_mtd_offset_size_format to the model
variable before stripping of garbage using awk will cause all NUL bytes to
be removed before awk is applied, leading to model strings like
"NETGEAR WNDRMACv2NETGEAR", where a NUL byte after the v2 is supposed to
terminate the string.

Fix by calling ar71xx_get_mtd_offset_size_format twice, once piping to awk
directly.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 48075
2016-01-03 11:09:45 +00:00
John Crispin
9242d27b4a V2 ar71xx : Add Support for the Bitmain Antrouter R1
This patch adds support for the Bitmain Antrouter R1

http://wiki.openwrt.org/toh/bitmain/r1

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 48058
2016-01-01 21:21:13 +00:00
Felix Fietkau
5359183b7e ar71xx: fix sysupgrade for wnr2200
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48005
2015-12-23 23:42:18 +00:00
John Crispin
e8c6d01d74 ar71xx: Update preinit script for new ath10k firmware
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 47985
2015-12-23 14:45:30 +00:00
John Crispin
772f9d4e32 ar71xx: Add support for AirTight Networks C-55
This patch is to add support for the AirTight Networks C-55 Access Point

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47973
2015-12-23 14:43:35 +00:00
Felix Fietkau
c74a690661 ar71xx: scan nand ubi partition for ath9k eeprom files
The MR18 stores the ath9k eeprom values on the NAND.
This patch makes it possible to retrieve the images
from there.

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47948
2015-12-19 11:28:36 +00:00
Felix Fietkau
8e4194797a ar71xx: refactor 10-ath9k-eeprom
move all library includes and 'firmware already exists'
check to the top of the script.

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47947
2015-12-19 11:28:30 +00:00
Felix Fietkau
fb1273dfdd ar71xx: PowerCloud CR5000 openwrt configuration
OpenWrt configuration part of support for the PowerCloud Systems
CR5000.  The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch.  The CR5000 was sold as
hardware for the Skydog cloud-managed router service.

    Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47946
2015-12-19 11:28:18 +00:00
Felix Fietkau
59fc337a9a ar71xx: PowerCloud CR3000 OpenWrt configuration
OpenWRt configuration part of support for the PowerCloud
Systems CR3000.  The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47945
2015-12-19 11:28:12 +00:00
Felix Fietkau
abc1faad0b ar71xx: PowerCloud CAP324 OpenWrt configuration
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP.  The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.

The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port.  It can be powered via PoE
or a wall wart.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47944
2015-12-19 11:27:59 +00:00
John Crispin
1f71f2220d ar71xx: add support for TRENDnet TEW-823DRU
Add support for TRENDnet TEW-823DRU:
- cpu: QCA9558 @720MHz
- flash: 16MB
- ram: 256MB
- 4+1 RJ45 100/1000Mbps
- wifi:  QCA9558 (bgn) and QCA9880-BR4A (ac)
- 1x USB 2.0

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 47927
2015-12-17 09:30:05 +00:00
Felix Fietkau
6b87e0706d ar71xx: Update merakinand.sh to fix sysupgrade
Remove reliance on /lib/upgrade/nand.sh as this is called by sysupgrade,
based on felix's comments at
https://lists.openwrt.org/pipermail/openwrt-devel/2015-December/037963.html

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47889
2015-12-13 18:05:42 +00:00
John Crispin
abc84551c0 ar71xx: add support for Cisco's MR18
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47878
2015-12-12 06:42:29 +00:00
Jo-Philipp Wich
67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
John Crispin
eb8ff56684 ar71xx: Add support for Wallys DR344
This patch is for Wallys DR344 support under OpenWRT

Signed-off-by: Philippe Duchein <wireless-dev@duchein.net>

SVN-Revision: 47847
2015-12-11 15:04:47 +00:00
Felix Fietkau
e4fd0a41fd ar71xx: fix switch port mapping for tl-wdr4300/3600
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47799
2015-12-06 14:25:36 +00:00
Jo-Philipp Wich
cc59f31e44 ar71xx: convert gpio switch config to board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47763
2015-12-04 15:02:42 +00:00
Jo-Philipp Wich
08848936dd all: remove redundant board.d/00_model files
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47753
2015-12-04 11:07:06 +00:00
Jo-Philipp Wich
527ec2af59 all: remove dummy ucidef_set_interface_loopback() from board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47744
2015-12-03 23:13:00 +00:00
Jo-Philipp Wich
feb8bf5ddc ar71xx: board.d: add missing include (#21296)
Include /lib/functions/system.sh in 02_network to define missing
mtd_get_mac_binary() procedure.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47723
2015-12-03 19:23:44 +00:00
Jo-Philipp Wich
8f8b702f85 board.d: remove redundant ucidef_set_interfaces_lan_wan() calls
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47722
2015-12-03 17:30:56 +00:00
Jo-Philipp Wich
9b02e73188 board.d: merge ucidef_add_switch() and ucidef_add_switch_ports()
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.

Also removes now superfluous enable and reset arguments.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47721
2015-12-03 17:30:24 +00:00
Jo-Philipp Wich
d17a64c7c0 base-files: uci-defaults-new: remove reset/enable args of ucidef_add_switch()
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.

This change ...

 * removes the reset and enable arguments from ucidef_add_switch()
 * unconditionally writes reset:1 and enable:1 to JSON
 * converts the three users of nonstandard values to ucidef_add_switch_attr()

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47720
2015-12-03 17:30:08 +00:00
Jo-Philipp Wich
81f603dfb8 ar71xx: record board id and model name in /etc/board.json
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47672
2015-11-30 10:17:20 +00:00
Jo-Philipp Wich
963fc89df2 ar71xx: switch network and led defaults to board detection framework
Also translate ucidef_add_switch_vlan() to ucidef_add_switch_ports() for better
switch topology mapping and improved default config generation.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47663
2015-11-26 14:42:28 +00:00
Jo-Philipp Wich
3fac6dde85 Revert "ar71xx: migrate led and network setup to board detection framework"
The board detect code needs more fixes in order to work properly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47641
2015-11-25 11:53:59 +00:00
John Crispin
1a092ce0e0 ar71xx: add GL-Domino Pi support V3
This is the patch for GL-Domino Pi V3. Updated against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47622
2015-11-24 18:30:50 +00:00
John Crispin
a04c3e73a3 ar71xx: add GL-AR300 support V3
This is the patch for GL-AR300 V3, tested against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47621
2015-11-24 18:30:19 +00:00
John Crispin
72093bd528 ar71xx: add GL-AR150 support V3
This is the 3rd version. Modified against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47620
2015-11-24 18:29:59 +00:00
Jo-Philipp Wich
7fc4a4581b ar71xx: fix network default config of the TEW-732BR
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47595
2015-11-22 20:00:13 +00:00
John Crispin
99fd9a7041 ar71xx: add support for the devolo dLAN Hotspot
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 47554
2015-11-21 21:24:18 +00:00
John Crispin
ac23207803 ar71xx: fix AR71XX_MODEL on TP-Link TL-WR703N
The hwid check was wrong, causing the AR71XX_MODEL value to end with a
space (as $hwver was unset).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 47553
2015-11-21 21:24:11 +00:00
Jo-Philipp Wich
605621fc3f ar71xx: fix wndr3700_board_detect for some NETGEAR WNDR3700v2 (again)
When fixing the model string for WNDR3700v2 which contain a model string
followed by 0xff in r46455, the match for other versions of the WNDR3700v2
which just contain lots of 0xff broke (as the 0xff $model is checked for
is stripped off).

Fix by stripping off non-printable characters only for the actual output
string, but not for the internal matching.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 47538
2015-11-20 23:34:11 +00:00
Jo-Philipp Wich
ade2c06d61 ar71xx: migrate led and network setup to board detection framework
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47534
2015-11-20 22:14:36 +00:00
Hauke Mehrtens
fa137d51f5 ar71xx: add Arduino Yun
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
7e2976fa83

The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.

Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47451
2015-11-10 23:13:09 +00:00
Felix Fietkau
7f75961e38 ar71xx: add support for TP-LINK TL-WR941ND v6 (international version)
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.

This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 47420
2015-11-08 20:39:18 +00:00
Felix Fietkau
ae7e7239b8 ar71xx: Add support for ZyXEL NBG6616.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>

SVN-Revision: 47405
2015-11-07 12:51:39 +00:00
John Crispin
8d8a937272 ar71xx: Add Gainstrong MiniBox v1.0 support to trunk
This patch supersedes the v1 from September 17th.

Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.

The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).

Fixed items:

- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.

Compiles fine, has been confirmed working by owners on 15.05.

Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?

Thank you

Signed-off by: Stijn Segers <francesco.borromini@inventati.org>

SVN-Revision: 47234
2015-10-19 17:55:25 +00:00
John Crispin
257e76a3df ar71xx: Bitmain Antminer S1 & S3 cleanup
Sets the LEDs to boardname:color:led-name
Sets the LAN to eth0
Other corrections such as the Machine Name and HWIDs
v2 corrects the profile names in the Makefile and changes tabs to spaces
in the Makefile 'define Device/' like the other devices.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 47221
2015-10-19 10:10:02 +00:00
John Crispin
03681684bf ar71xx: Correct WeIO board name
Trivial parch to correct WeIO board name in the system.

Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>

SVN-Revision: 47110
2015-10-05 10:25:40 +00:00
Felix Fietkau
896d3e3e13 ar71xx: Add WeIO Board Support
Add support for WeIO board (http://we-io.net).
This board is based on Carambola2 board form 8Devices.

Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups]

SVN-Revision: 47036
2015-09-24 09:08:47 +00:00
John Crispin
ac75fc8d98 ar71xx: add support for ap152 reference board
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46972
2015-09-16 08:33:14 +00:00
John Crispin
fa09d76521 ar71xx: uci-defaults: fix ap143 to appropriate group
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46970
2015-09-16 08:32:56 +00:00
John Crispin
1297679f4b ar71xx: Add UBNT airGateway Pro support
This patch adds kernel and userspace support for the Ubiquiti Networks airGateway Pro.

Signed-off-by: Matthew Reeve <mreeve at tenxnetworks.com>

SVN-Revision: 46961
2015-09-16 08:31:40 +00:00
John Crispin
0dbced8a48 ar71xx: add TP-LINK TL-WDR3320 v2 support
This patch adds support for TP-LINK TL-WDR3320 v2.

This router uses a chinese version 2 firmware header,.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 46934
2015-09-14 20:12:16 +00:00
John Crispin
bfeae90850 ar71xx: extract ath10k wifi board.bin for the OpenMesh MR1750 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46933
2015-09-14 20:12:00 +00:00
John Crispin
b9b6d34e36 ar71xx: enable sysupgrade for the OpenMesh MR1750
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46929
2015-09-14 20:11:24 +00:00
John Crispin
cbf71651ec ar71xx: add user-space support for the OpenMesh MR1750 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46927
2015-09-14 20:11:01 +00:00
John Crispin
d1587fb4aa ar71xx: assign proper GPIO pin for Ubiquiti Nanostation models
The GPIO pins for "POE passthrough" of Ubiquiti Nanostation models are the
following:
* Ubiquiti Nanostation M XM: Pin 8
* Ubiquiti Nanostation M XW: Pin 2

The previous definition of the pins was mixed up between XM and XW model.

Signed-off-by: Lars Kruse <lists@sumpfralle.de>

SVN-Revision: 46922
2015-09-14 20:09:40 +00:00
Felix Fietkau
2ce833060a target: ar71xx: add support for COMFAST CF-E316N v2 board
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 46852
2015-09-11 16:31:35 +00:00
John Crispin
af60c367b7 ar71xx: add support for TP-Link TL-WDR6500 v2
Signed-off-by: Weijie Gao <hackpascal@gmail.com>

This patch adds support for TP-Link TL-WDR6500 v2.

The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.

SVN-Revision: 46663
2015-08-17 06:24:04 +00:00
John Crispin
4463bc017b ar71xx: Add support for Black Swift
Add support for the Black Swift board:
http://www.black-swift.com/

Took relevant parts and slightly adapted from:
https://github.com/blackswift/openwrt/blob/master/bsb.patch

Signed-off-by: Bruno Randolf <br1@einfach.org>

SVN-Revision: 46651
2015-08-17 06:16:54 +00:00
John Crispin
5cd49bb067 ar71xx: add support for Onion Omega
This patch adds support for the Onion Omega.

https://onion.io/omega

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>

SVN-Revision: 46458
2015-07-24 09:09:49 +00:00
John Crispin
b98205c946 ar71xx: Add support for AP147-010 reference board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46457
2015-07-24 09:09:42 +00:00
John Crispin
85c7f3fb29 ar71xx: fix wndr3700_board_detect for some NETGEAR WNDR3700v2
There are a few NETGEAR devices which don't terminate the model name in the
ART with a NUL byte, at least some NETGEAR WNDR3700v2. The current awk
expression doesn't match 0xFF bytes, so AR71XX_MODEL contains lots of
trailing 0xFF garbage in this case.

Fix this by matching for the first non-printable character and explicitly
setting LC_CTYPE=C (probably not strictly necessary on OpenWrt, but will
definitely work like this, even when awk supports locales and LANG is set).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 46455
2015-07-24 09:09:27 +00:00
Felix Fietkau
d26e8d9439 Revert "ar71xx: Add support for Cisco-Linksys WAP4410N" (r46250)
The commit is incomplete, it does not even build the mach-* file

This reverts commit 6e6adcf7a197b1802cb728ddcccf05f890ca0574

SVN-Revision: 46425
2015-07-19 17:58:27 +00:00
John Crispin
c89f360059 ar71xx: Enable ath10k calibration data loading for EnGenius ESR1750 and EPG500.
As r46245 disabled the board.bin template workaround, 5GHz wifi stopped working
on these devices. This adds them to the calibration data loading introduced in
r46244 and thus makes 5GHz work again for these devices.

Signed-off-by: Christian Beier <cb@shoutrlabs.com>

SVN-Revision: 46415
2015-07-18 21:15:42 +00:00
John Crispin
1eccdb4fd4 ar71xx: add support for the devolo dLAN pro 1200+ WiFi ac
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 46342
2015-07-14 07:37:03 +00:00
John Crispin
02984a6e09 ar71xx: add support for the devolo dLAN pro 500 Wireless+
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 46338
2015-07-14 07:32:33 +00:00
John Crispin
dc2c89c64c ar71xx: fix board name ordering
r46248 added case statements in the same places

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46274
2015-07-08 14:26:18 +00:00
John Crispin
d65916047b base-files: implemented basic GPIO control
Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.

Signed-off-by: Lars Kruse <lists@sumpfralle.de>

SVN-Revision: 46271
2015-07-08 14:25:52 +00:00
John Crispin
227aafc4db ar71xx: Fix LED-to-phy mapping for EnGenius ESR1750.
wlan5g is phy0tpt and wlan2g phy1tpt.

Signed-off-by: Christian Beier <cb@shoutrlabs.com>

SVN-Revision: 46270
2015-07-08 14:25:45 +00:00
John Crispin
08790c5ee8 ar71xx: Add support for Cisco-Linksys WAP4410N
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.

Signed-off-by: Ryan A Young <rayoung@utexas.edu>

SVN-Revision: 46250
2015-07-07 18:06:39 +00:00
John Crispin
d535218230 ar71xx: add support for D-Link DIR-615 rev. Ix board
Based on trunk r46212.

Signed-off-by: Jaehoon You <teslamint@gmail.com>

SVN-Revision: 46248
2015-07-07 13:48:39 +00:00
John Crispin
f3bdc4a76a ar71xx: Unify ath10k calibration data loading
Currently one board uses the "proper" way of providing firmware
with the name ath10k/cal-pci-<pci address>.bin, whereas other
boards patch board.bin template in preinit and rely on a custom
ath10k patch to use calibration data from the template.

This patch makes all boards use the first method.

Signed-off-by: Matti Laakso <malaakso@elisanet.fi>

SVN-Revision: 46244
2015-07-07 13:47:57 +00:00
John Crispin
055663201b ar71xx: Add Support for the Bitmain Antminer S3
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner

http://wiki.openwrt.org/toh/bitmain/s3

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46236
2015-07-07 13:46:54 +00:00
John Crispin
6fc2e94120 ar71xx: add support for ubnt rocket-m ti
rocket-m titanium is a device based on ar9344 with 802.11af poe.
It doesn't use the SoC wifi, instead it's using an ar9280 connected to
the pci bus. The gps version of the rocket-m ti is working, but
gps is untested. The gps is connected to the first serial port.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 46234
2015-07-07 13:46:38 +00:00
John Crispin
404e599933 ar71xx: Enable sysupgrade on the Bitmain Antminer S1
This patch enables sysupgrade for the Bitmain Antminer S1

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46228
2015-07-07 13:45:37 +00:00
John Crispin
5740cf684c ar71xx: Fix WAN port location on EnGenius ESR1750 and EPG5000.
The designated blue WAN port on both devices has index 5, not 1.

Signed-off-by: Christian Beier <cb@shoutrlabs.com>

SVN-Revision: 46227
2015-07-07 13:45:30 +00:00
John Crispin
6a374f0062 ar71xx: add LED defaults for the EnGenius EPG5000
NB that wlan5g is phy0tpt and wlan2g phy1tpt.

Signed-off-by: Christian Beier <cb@shoutrlabs.com>

SVN-Revision: 46226
2015-07-07 13:45:20 +00:00
Felix Fietkau
b26077026f ar71xx: add support for ap143
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46208
2015-07-07 08:06:05 +00:00
Felix Fietkau
6eea8046b3 ar71xx: update preinit script for new ath10k firmware
Update firmware name and md5sum. MAC-address location remains
unchanged from previous version.

Signed-off-by: Matti Laakso <malaakso@elisanet.fi>

SVN-Revision: 46196
2015-07-06 10:19:21 +00:00
John Crispin
1f038e0678 ar71xx: add user-space support for EnGenius EPG5000.
Signed-off-by: Christian Beier <cb@shoutrlabs.com>

SVN-Revision: 46048
2015-06-18 18:21:41 +00:00
John Crispin
e85f3471ba ar71xx: add support for TL-WR720N-v4.
The hardware should be almost the same as TL-WR720N-v3.  WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>".  Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 46046
2015-06-18 18:21:23 +00:00
John Crispin
8399be545a ar71xx: add support for compex wpj531
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj531-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46045
2015-06-18 18:21:15 +00:00
John Crispin
694dd581eb ar71xx: Add Support for the Bitmain Antminer S1
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner

http://wiki.openwrt.org/toh/bitmain/s1

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>

SVN-Revision: 46044
2015-06-18 18:21:05 +00:00
Felix Fietkau
008a0ebc56 ar71xx: fix mac offset in firmware file
In new firmware-4.bin (for ath10k) mac offset is 0x114 (276), not 0x118 (280).
This also closes #19751, bug introduced in #45624

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 45958
2015-06-14 17:41:27 +00:00
John Crispin
7d8de52d4d ar71xx: fix AR71XX_MODEL for TP-Link TL-WA830RE v1
The v1 identifies as v10 internally. As there is no TL-WA830RE v10, add a
workaround to avoid confusing users.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45903
2015-06-05 14:12:34 +00:00
John Crispin
66950455b7 ar71xx: Add support for the Meraki MR12 & MR16
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.

Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>

SVN-Revision: 45726
2015-05-23 15:27:22 +00:00
Felix Fietkau
b33752051f ar71xx: add platform_pre_upgrade for sysupgrade
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45667
2015-05-10 13:54:25 +00:00
Luka Perkov
2a9ebfb503 ar71xx: add status led found on ew-dorin boards
Signed-off-by: Catrinel Catrinescu <cc@80211.de>

SVN-Revision: 45656
2015-05-10 07:47:04 +00:00
Felix Fietkau
5c5648f4b7 ar71xx: track the correct WAN interface on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45632
2015-05-08 12:23:40 +00:00
Felix Fietkau
6b6cc03cff ar71xx: fix LAN portmasks on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45631
2015-05-08 12:23:35 +00:00
Felix Fietkau
a51f5cace4 ar71xx: use a common naming scheme for LEDS on wnr2000-v4
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45630
2015-05-08 12:23:27 +00:00
Felix Fietkau
4babe9dc6d ar71xx: fix 82_patch_ath10k
It has been broken since the new ath10k firmware introduced in r44656.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 45624
2015-05-08 10:43:55 +00:00
Luka Perkov
cd419afd2c ar71xx: fix sysupgrade for compex-wpj344
Moved board to the right magic case.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 45588
2015-04-29 13:52:34 +00:00
John Crispin
a34db67857 Add support for Ubiquiti Rocket M XW devices
This patch adds support for the XW version of the Rocket M series devices
manufactured by Ubiquiti, based on the Atheros AR9342 SoC.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 45553
2015-04-21 12:42:13 +00:00
Luka Perkov
9d76de9771 ar71xx: add support for compex wpj344
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45527
2015-04-20 20:47:48 +00:00
John Crispin
8f92e94a74 ar71xx: enable LEDs on Hornet-UB X2
None of the LEDs are enabled by default on the Hornet-UB X2 board
(the 16/64MB version of the Hornet-UB), because it uses a different
board-name ("hornet-ub-x2"); but hornet-ub and hornet-ub-x2 boards
are equivalent WRT their LEDs.

SIgned-off-by: Joshua Judson Rosen <jrosen@harvestai.com>

SVN-Revision: 45328
2015-04-09 10:32:08 +00:00
Gabor Juhos
0bd06aca20 ar71xx: add user-space support for RB911G-5HPacD
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 45300
2015-04-07 20:04:14 +00:00
John Crispin
23d37c1208 ar71xx: fix model string detection on NETGEAR WNDR3700/3800/WNDRMAC
There were a few issues with the existing code to detect the model string:
* Always using the string starting with byte 56 would cut off the W of WNDR when
  the ID starts with 29763654+16+64 instead of 29763654+16+128
* The string contained garbage after the zero byte instead of cutting it off
  after the zero (which wasn't always visible using busybox tools, but could
  confuse other scripts)

Tested on a WNDR3700v1 and a WNDR3700v2 using the new 29763654+16+64 ID in the
ART. Furthermore, tested against ART dumps of a WNDR3700v2 using the old
$'\xff...' value and a WNDR3800.

The [ -z "$model" ] check was dropped as there is no way to actually hit this
unless no ART partition is found at all.

The awk command was carefully crafted to work both with gawk and the (horribly
broken) busybox awk.

Fixes #18992.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45140
2015-03-29 12:58:01 +00:00
John Crispin
10c5a44017 ar71xx: enable sysupgrade for the OpenMesh OM5P-AN
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 44863
2015-03-17 09:43:37 +00:00
John Crispin
85cceb5dd0 ar71xx: add user-space support for the OpenMesh OM5P-AN
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 44862
2015-03-17 09:43:31 +00:00
John Crispin
2a0fcc029f ar71xx: detect GL.iNet model
There are two versions of the GL.iNet, the 6408A and the 6416A. The only
difference is the flash size.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 44860
2015-03-17 09:43:13 +00:00
John Crispin
abdf788610 ar71xx: fix switched WLAN LEDs on TP-LINK Archer C5/C7
ath10k is loaded before ath9k, so the 5GHz adapter becomes phy0.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 44659
2015-03-11 15:55:06 +00:00
John Crispin
5801465eb3 ar71xx: Fix board detection for the TP-LINK TL-MR13U.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 44646
2015-03-10 13:26:44 +00:00
Luka Perkov
b065411a85 ar71xx: add support for compex wpj558
OpenWrt can be flashed with following uboot commands:

tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44620
2015-03-06 14:41:57 +00:00
John Crispin
9358a8a798 ar71xx: TL-WA7210n v2 support
This patch adds support for TP-Link TL-WA7210n[0]

[0] http://www.tplink.com/en/products/details/?model=TL-WA7210N

Signed-off-by: Hendrik Frenzel <hfrenzel@scunc.net>

SVN-Revision: 44526
2015-02-24 12:00:50 +00:00
Jo-Philipp Wich
f9aa2ec7f6 ar71xx: fix 82_patch_ath10k
The firware md5sum check never worked due to missing dollar signs.

Also suppress
  `md5sum: can't open '/lib/firmware/ath10k/QCA988X/hw2.0/firmware-3.bin'`
error on any board not using ath10k.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 44486
2015-02-17 21:26:39 +00:00
John Crispin
bd5635770c ar71xx: Add user-space support for TP-Link MR12U v1
This patch adds user-space support for the TL-MR12U board based on the mr13u patches.

Signed-off-by: Daniel Petre <daniel.petre@gmail.com>

SVN-Revision: 44426
2015-02-13 07:29:03 +00:00
John Crispin
de8d6e447c ar71xx: ZyXEL NBG6716 led/buttons cleanup
ZyXEL NBG6716 led/buttons cleanup
 - improper numbered leds
 - improper named buttons

Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>

SVN-Revision: 44417
2015-02-12 08:07:27 +00:00
John Crispin
a2fcaa77fc ar71xx: add mc-mac1200r to do_load_ath10k_board_bin()
This patch adds the mc-mac1200r target to do_load_ath10k_board_bin() in
target/linux/ar71xx/base-files/lib/preinit/81_load_ath10k_board_bin to load the
ath10k radio MAC address from the EEPROM in MERCURY MAC1200R devices

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 44375
2015-02-10 05:52:53 +00:00
John Crispin
a5b60de253 ar71xx: Add support for MERCURY MAC1200R
This patch adds support for MERCURY MAC1200R, a dual band 802.11bgn + 802.11ac
router based on the AR9344, with QCA988x ath10k radio and 5 Fast Ethernet ports

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 44359
2015-02-09 12:16:51 +00:00
John Crispin
35d38f21e0 ar71xx: fix nbg6716 power and usb led
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Marcin Mikolajczak <gr4ffy@gmail.com>

SVN-Revision: 44358
2015-02-09 12:16:43 +00:00
Luka Perkov
54ac4e0600 ar71xx: uci-defaults: add el-mini to appropriate group
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44307
2015-02-07 19:59:05 +00:00
Luka Perkov
81db848656 targets: base-files: diag.sh does not need to be executable
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44305
2015-02-07 19:58:58 +00:00
Luka Perkov
92e6e80080 targets: files in uci-defaults do not need to be executables
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44304
2015-02-07 19:58:52 +00:00
John Crispin
cde2225c7c ar71xx: add support for the TP-LINK TL-WR941ND v5
This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 44255
2015-02-04 06:10:20 +00:00
John Crispin
a63e94426d at71xx: TP-LINK Archer: add 5GHz led entry
Add 5GHz led entry after r44033.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 44254
2015-02-04 06:10:12 +00:00
John Crispin
baaef42952 ar71xx: Revert "added board support for compex wpj558"
This reverts commit f7873071561d82e75ba2dc46433a2982fef8ac6f.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44245
2015-02-02 10:32:04 +00:00
John Crispin
bc906ca59e added board support for compex wpj558
Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 44237
2015-02-02 09:00:21 +00:00
John Crispin
31fd66f808 ar71xx: add Netgear WNR1000v2/WNR1000v2-VC support (#18633)
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.

Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>

SVN-Revision: 44221
2015-01-30 08:06:40 +00:00
John Crispin
09a227a191 ar71xx: add default LED configuration for D-Link DIR-615 rev. C1
This patch adds an entry in the uci-defaults' led-file to configure the
WAN and WLAN LEDs by default.

Signed-off-by: Vincent Wiemann <me@bibbl.com>

SVN-Revision: 44165
2015-01-28 12:06:13 +00:00
John Crispin
df2e312100 ar71xx: add support for TP-LINK TL-WR843ND v1
TP-LINK TL-WR843ND v1 is the same model like wr41, but with
Power over Ethernet on wan port.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 44085
2015-01-23 12:32:46 +00:00
John Crispin
ae70358b1b ar71xx: add support for the UniFi AP Outdoor Plus
the GPIO controlling the rf filter is not configured properly by this patch.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 44077
2015-01-22 09:35:46 +00:00
John Crispin
4961c7d0f5 ar71xx: add support for TL-WA701ND v2
Signed-off-by: Luigi Tarenga <luigi.tarenga@gmail.com>

SVN-Revision: 44063
2015-01-20 15:48:07 +00:00