HC5661A is almost the same as HC5661 but MT7628AN is used instead of MT7620A.
- MT7628AN
- 128 MiB DDR2 RAM (W971GG6KB-25)
- 16 MiB SPI NOR flash (W25Q128)
- SD slot (not work yet)
- 1+4 x 100M Ethernet
- 802.11 b/g/n Wi-Fi
- 3 x LED
- 1 x button
- UART pad on PCB (JP1: TX, RX, GND, 3.3V)
The factory flash layout seems different from HC5661.
"hwf_config" is renamed to "oem" and its size changes to 0x20000.
It is modified accordingly in the dts file.
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "hw_panic"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000160000 : "kernel"
0x000000160000-0x000000fc0000 : "rootfs"
0x000000bb0000-0x000000fc0000 : "rootfs_data"
0x000000fc0000-0x000000fe0000 : "oem"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "backup"
0x000000050000-0x000000fc0000 : "firmware"
To install LEDE, enabled the "developer mode",
which will *void your warranty* and open the SSH server at port 1022.
sysupgrade -n -F lede-ramips-mt7628-hc5661a-squashfs-sysupgrade.bin
SD slot:
- Tried to add modules kmod-sdhci kmod-sdhci-mt7620, and corresponding dts block.
- It will block WAN + 3xLAN ports, only one LAN works.
- I'm not sure why, everything else works fine.
Signed-off-by: Wang JiaWei <buaawjw@gmail.com>
The following will enable the TPM kernel module, as well as support for
the atmel i2c TPM driver. Tested and confirmed working on an Aerohive
AP-121
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The more straight forward approach for generating the pure and unpadded
kernel file which then can be used for initramfs straight.
Build options for factory.img and sysupgrade.tar are handeled
seperately.
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
On Mikrotik SPI NOR devices, the firmware partition must be erased when flashing
from stock firmware, otherwise leftover bits (in particular a kernel signature)
can trigger a boot loop.
When booted from initramfs (the only way to flash LEDE on these devices),
this patch unconditionally erases the firmware partition in the pre_upgrade()
stage for all supported SPI NOR devices.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch frees up flash space on the EX2700, by
removing unused mt76 drivers and firmware.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
Backport kernel patches for LS1043A Rev1.1 support from upstream,
patchwork, and SDK. And update to latest u-boot to support LS1043A
Rev1.1.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The ethernet driver uses a port map override via special tag to control
the ports on which multicast packets are sent. This was added to work
around an issue in the switch that was occasionally leaking packets onto
the wrong vlan.
Unfortunately the change had some leftover lines that were overwrting
the port map with a list of all ports, thus always leaking packets onto
the wront vlan.
Fix this by only enabling the override with the VLAN port map and only
if a matching VLAN port map was actually found
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bump kernel from 4.4.49 to 4.4.50
Compile tested: All targets
Run tested: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This patch enables mtdsplit for the MikroTik subtarget.
It converts mach-rbspi.c to use a single "firmware" partition.
Finally, it converts the SPI NOR profile to metadata images:
the original combined-image format is gone, the images are now
"standard" sysupgrade images with metadata appended.
Note: kernel2minor apparently pads the kernel container to erase-block
boundary, but this is undocumented behaviour, so we do not rely on it
and call pad-to anyway.
Note: in platform.sh, the boards are tested last in platform_check_image()
as this should eventually become the "*)" default case when more devices
switch to metadata images.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The RouterBOOT bootloader does not care where the kernel lives in the SPI
flash, all that matters is that the kernel is wrapped in the custom yaffs
container as generated by kernel2minor.
This container has a fixed signature as follows:
00000000 00 00 00 01 00 00 00 01 ff ff 6b 65 72 6e 65 6c |..........kernel|
This patch adds mtdsplit support for identifying that signature and
triggering the search for the rootfs. rootfs is expected at EB boundary since
we use wget mtd_find_rootfs_from(). We make no use of the yaffs file size
field because it contains invalid data in the image generated by kernel2minor.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The fakeroot header is expected by the netgear bootloader in the last
64 bytes of the last block used by the uImage. With the current
linux-4.9 uImage being more than 128k smaller than the linux-4.4 uImage
the bootloader was unable to locate the rootfs ih_magic and was
refusing to load and start the kernel.
Fixes: FS#542
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
CONFIG_FB_EFI and CONFIG_FB_SIMPLE are needed to display console text on
EFI framebuffer.
CONFIG_FB_EFI is needed when the kernel is directly launched via EFI
shell or EFI startup.nsh script.
CONFIG_FB_SIMPLE is needed when launching the kernel via grub2 efi. In
this case, grub2 has prepared a gfxterm framebuffer and the kernel just
need to use the already prepared grub's gfxterm framebuffer to display
console text.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
For AR71XX devices, GMAC1 always connects port 0 of the built-in switch,
as the CPU port.
This patch sets correct vlan for some devices with wrong settings:
a) mark port 0 as CPU port, tagged
b) reverse port order, marking these ports untagged
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for the TP-Link TL-WR802N Version 2.
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of FLash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)
Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to http://192.168.0.1 (default user is "admin" & password is "admin)
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware "*.factory-us.bin" or "*.factory-eu.bin" for eu model
- Click upgrade
Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
Serial Configuration 115200 8n1
- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
(IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
(e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
(e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
(e.g bootm 0x9f020000)
Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
Fixes the following warning on first boot if the ltq_atm modules are
not included in the image:
ls: /lib/modules/4.4.49/ltq_atm*: No such file or directory
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the nas0 interface for the netdev trigger as default. Use the ptm0
interface for xRX200 boards to match the default wan interface set in
02_network.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move the code to check if the current system is a system with vdsl
support to a dedicate function to make it reusable.
Signed-off-by: Mathias Kresin <dev@kresin.me>
QCA956x is configured like AR934x, not like the older chips.
Should fix ethernet hangs when using the WAN port without SGMII
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This makes the Geode images actually useful again. The Geos profile
should include the relevant hardware for that board, and the Default
profile adds the via-rhine adapter which seems to have been present in
the net5501 and alix targets killed in commit 9e0759ea26 ("x86: merge
all geode based subtargets into one").
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO
Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery
Tested on:
- Lima development kit
Signed-off-by: Karol Dudek <karoiz@sli.pl>
commit 33b72b8e0f
"ar8216: adjust ATU flushing in case of link changes"
introduced portwise flushing on link down events. Now the ARL table could
be in a chaotic state after boot where ar8xxx_sw_get_arl_table looped
forever (depending on the entries collected while booting).
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict
[ 0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm
[ 0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22
[ 0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0 on device rt2880-pinmux
[ 0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back
Keep PWM disabled.
Signed-off-by: Furong Xu <xfr@outlook.com>
