This fixes some strange problems with tg3. I assume that the Ethernet
driver was not brought up if the switch was named switch0.
This was reported and tested by ernesto (Faulp3lz).
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41042
Instead of looking into the proc entry provided by broadcom-diag use
the board info from /proc/cpuinfo to get the board we are on.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39256
Use the new led api also on brcm47xx.
The led for failsafe indication is searched for.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39255
Some time ago, after switching to the mainline bcm47xxpart driver
following patch has been applied:
commit 03cef8725d2062335ffc3de50fc037b294fd458c
Author: hauke <hauke@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Sat Apr 6 22:22:26 2013 +0000
brcm47xx: use old partition names again for kernel 3.8
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.
Thank you russell for spotting this problem.
I propose to revert this change and make sysupgrade use "firmware"
instead. This makes brcm47xx compatible with widely used ar71xx and
after all "firmware" sounds like a much better name for... the firmware.
This change doesn't affect "sysupgrade" usage, because it never takes a
partition name as a parameter. This change only affects users using mtd
tool directly. Hopefully there are not many howtos using "mtd" command.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38973
Modify /etc/init.d/netconfig to use UCI defaults for building the
default network config, which includes appropriate defaults for IPV6.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38294
This makes it possible to use swconfig to controll the switch.
This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.
SVN-Revision: 37304
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.
Thank you russell for spotting this problem.
SVN-Revision: 36235
The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.
This makes OpenWrt always use vlan1 and vlan2 instead.
SVN-Revision: 35704
This contains the following new bigger changes:
* new partition parser which still could lake some features or have bugs
* new nand flash driver
* using physmap-flash flash driver for parallel flash
* some changes to the serial flash driver
With these changes OpenWrt starts using more of the mainline flash drivers.
SVN-Revision: 35632
The included patch will generate a correct network configuration on the simpletech simpleshare.
Thank you for the patch Will Holmes (RealOpty)
This closes#12361.
SVN-Revision: 35623
Hi,
this patch adds the correct vlan definitions for the Siemens SE505v2. It
applies to trunk as well as backfire (please apply here too). On
backfire this also patches brcm-2,4, because brcm47xx base-files is just
symlinked to brcm-2.4.
It also fixes two whitespace issues.
Tested with brcm47xx on both trunk and backfire branch and works as
expected.
Signed-off-by: Manuel Munz <freifunk@somakoma.de>
SVN-Revision: 28336
