Fixes these prints on boot:
[ 13.785600] imx-uart 2020000.serial: DMA transaction error.
[ 13.793134] imx-uart 2020000.serial: DMA transaction error.
[ 13.798721] imx-uart 2020000.serial: DMA transaction error.
Based on following upstream patch by Tim Harvey (Gateworks):
80a01b6582
TX complete DMA messages are getting missed.
This is also currently an issue in mainline.
For now we will disable DMA in serial/imx.c.
This resolves an issue encountered with RS485 transmit.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The "reserved" partition should probably be read-only, just in case. Even
not knowing it's content, other devices have marked it as such, so it
seems a good idea to do so also for this device.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Mathias Kresin <dev@kresin.me>
CC: Hanqing Wong <hquu@outlook.com>
This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board
and sets color of all LEDs to green as the mass production boards have
only green one.
Actually, DR344 has 6 GPIO-connected LEDs and one button:
- GPIO11: status
- GPIO12: sig1
- GPIO13: sig2
- GPIO14: sig3
- GPIO15: sig4
- GPIO16: reset button
- GPIO17: lan
WAN LED is connected directly with AR8035 PHY.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This aligns default network interfaces configuration with vendor
firmware: GE (eth0) -> wan, FE (eth1) -> lan.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GMAC0 interface of AR9344 SOC in Wallys DR344 board is connected with
AR8035, not with AR8327. Without this fix, GE interface doesn't work at
all or shows high packet loss ratio.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.
The device is based on Qualcomm/Atheros AR9341 v1.
Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button
Flash instructions:
You have three options:
- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.
- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.
- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:
*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
stat -- Status
sys -- System
wless2 -- 2.4G-Wireless
mgmt -- Management
tree -- Tree
help -- Help
reboot -- Reboot
ens202ext>mgmt
Management
---========= Commands Help =========---
admin -- Administration
mvlan -- Management VLAN settings
snmp -- SNMP settings
backup -- Backup/Restore settings
autorb -- Auto reboot settings
fwgrade -- Firmware upgrade
time -- Time settings
wifisch -- Wifi schedule
log -- Log
diag -- Diagnostics
disc -- Device Discovery
logout -- Logout
help -- Help
exit -- Exit
ens202ext/mgmt>fwgrade
Management --> Firmware upgrade
---========= Commands Help =========---
fwup -- Firmware upgrade
help -- Help
exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin
Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
The single SFP port is meant for direct media access to WAN, such as
VDSL2, GPON). While it could also be used for in-home fiber, it is much
more likely that the LAN is standard ethernet, especially considering
that SFP is the onmly port that can go beyond 1Gbps.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Take explicit note of what physical ports eth{0,1,2} refer to.
Also repair port assignment:
At some point between 4.9.20 and 4.9.29 the numbering changed.
Keep previous port assignment that was:
LAN = SFP+Switch
WAN = standalone ethernet
Also use the same assignment for Clearfog-Base to avoid confusion.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Installing all armada-388-clearfog-* DTBs in the same sdcard image,
it now becomes much easier to swap sdcards between different device variants.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
U-Boot provides standard variables for load addresses, and
filesystem-agnostic load-commands. Furthermore thanks to distro-boot,
the device and partition from which the system boots is known.
The new boot-script makes use of all this information.
Tested on the only board that uses this boot-script: Clearfog Pro
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
sunxi sysupgrade was based on the x86 implementation; sync fixes and other
changes from the current x86 version:
x86: fix sysupgrades on disks with 4k block size
x86: sysupgrade: move partition table change check to platform_check_image
x86: sysupgrade: refactor platform_do_upgrade
x86: sysupgrade: explicitly rescan disk after writing partition table
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
When existing partitions are retained, the dd call writing the uboot image
in the space before the first partition was accidentally writing the whole
image, making the code for individual partitions redundant. Limit the copy
to 1016KiB (the first 8KiB are skipped, and the first partition starts at
1024KiB).
In addition, conv=notrunc is replaced with conv=fsync. It seems this was an
oversight, as notrunc doesn't make sense for block devices and all other dd
commands use conv=fsync.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This should ensure that the kernel partition can be mounted in
platform_copy_config when its size has changed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
By returning early when no upgrade device can be found and handling the
SAVE_PARTITIONS=0 case differently, we can get rid of two levels of if.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The staged sysupgrade will prevent us from using ask_bool in
platform_do_upgrade; therefore, the check is moved to platform_check_image.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
All targets with NAND support should gradually move their nand_do_upgrade
calls from platform_pre_upgrade to platform_do_upgrade.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This change adds QPIC BAM dma and NAND driver node's in IPQ4019
device tree, also enable this for AP-DK04.1 based boards.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
This change adds support for below:
- Bam transaction which will be used for any NAND request.
- Reset function for NAND BAM transaction
- Add support for additional CSRs.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
The existing qcom_nand driver supports ADM DMA which is mainly
required for ipq806x family based boards,
IPQ40xx based boards uses BAM DMA in NAND driver, so this patch
adds BAM DMA support with compatible string as qcom,ebi2-nandc-bam.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
GPIO_PULL bits configurations in TLMM_GPIO_CFG register
differs for IPQ40xx from rest of the other qcom SoC's.
This change add support to configure the msm_gpio_pull
bits for ipq40xx, It is required to fix the proper
configurations of gpio-pull bits for nand pins mux.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
The generic preinit code is now able to setup network and switch vlan settings
from the /etc/board.json file, therefor drop the target specific code.
Fixes FS#790.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.
Hardware Specification (v1.0 EU):
- SoC: QCA9531
- Flash: Winbond W25Q64FV (8MiB)
- RAM: EtronTech EM6AB160TSE-5G (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 2NIC (3x100M + 1x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 12V 1A
Signed-off-by: Filip Moc <lede@moc6.cz>
Neither the AsiaRF AWM002 or AWM003 actually has an LED on the module
board. The ld1 and ld2 do not represent actual LEDs. These pins might
connect to LEDS on an eval board or other carrier board, but that is
outside the scope of this device tree file.
Signed-off-by: Russell Senior <russell@personaltelco.net>
UML statically links against libutil, librt and libpthread. Some hosts do not
necessarily have these libraries installed and we should find out sooner than
later (during the final vmlinux linking stage) about that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The device tree is at /proc/device-tree/ without a base subdir.
Fixes: da472e5b30 ("treewide: access device tree from userspace via /proc/")
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds supports for the GL-inet GL-MT300N-V2.
Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)
Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.
Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.
Signed-off-by: Kyson Lok <kysonlok@gmail.com>
[match maximum image size with firmware partition]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Access the device tree via /proc/device-tree/ is the documented way to
access the properties. Everything else might not work in future.
Signed-off-by: Mathias Kresin <dev@kresin.me>
commit 961c0eacea ('x86: fix lifting kernel CPU requirements and always
enable PAE') broke some older geode boards such as Soekris net4826.
Hence disable PAE on x86/legacy again in order to still support those
very old non-PAE capable CPUs.
Fixes FS#773 - PAE broke Soekris net4826
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This PR allow the 3G modem embedded in the DWR-512 to be managed
by the wwan-ncm scripts. The modem will use the usb-option and
usb-cdc-ether drivers.
The DWR-512 DT is updated accordingly.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
These drivers are in many reference-design Xeon, iCore, or
Atom64 based server boards.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This change is required to make the GBit switch work on my Mikrotik Routerboard RB2011UiAS-RM, and I assume that the other RB2011 variants are exactly the same in terms of the switch. I have tested the board without and with the patch and confirm that the GBit ports are not supported at all (i.e. no communication works) with the current version in trunk and that everything works with the patch applied. The test box has been running for a few days with the patch applied, and does not show any performance problems in a test setting. I have not used it with LEDE in production so far, but with a previous turnk version of OpenWRT for many years - with the same patch applied. I therefore have good indication that it is stable.
For the record, the switch chip on my test box is identified as
switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
The value 0x6f000000 has been taken from the table at https://wiki.openwrt.org/toh/mikrotik/rb2011uias with the previous discussion thread still online at https://lists.openwrt.org/pipermail/openwrt-devel/2014-December/029949.html.
One definite improvement from the older OpenWRT trunk version I have been running in production and current LEDE trunk is that the SFP interface can be kept in the default configuration without excessive kernel messages about it constantly going up and down. I have not yet tested an actual SFP module, though.
Performance seems to be reasonable. Routing between two GBit ports on that switch separated by different VLANs with the default firewall ruleset (and one additional rule two allow traffic between the VLANs), but without NAT, iperf3 results are:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 508 MBytes 426 Mbits/sec 102 sender
[ 4] 0.00-10.00 sec 506 MBytes 425 Mbits/sec receiver
With a connection going through NAT (also 2 ports on the same GBit switch, same ruleset, but NAT active), routing performance drops to around 250 MBit/s.
(Note that RouterOS achieves beyond 900 MBit/s on the same hardware with the default rule set and the FastTrack rule active even for NAT, see https://wiki.mikrotik.com/index.php?title=Manual:IP/Fasttrack and http://www.mikrotik.com/download/share/FastTrack.pdf).
Summarizing, I strongly recommend to apply this patch in trunk, so that the GBit switch chip rev. 4 can be supported upstream in the next LEDE release (hopefully soon).
Signed-off-by: René Mayrhofer <rene@mayrhofer.eu.org>
changes the image version from hardcoded OpenWrt to
$VERSION_DIST. AirOS shows a notification with the image version
during a firmware upgrade.
fixes#582
Signed-off-by: Matthias Fritzsche <txt.file@txtfile.eu>
With cpufreq disabled, the CPU stays locked at the frequency set by the
bootloader. This severely degrades performance as the bootloader sets
the CPU at the lowest frequency by default.
Enable cpufreq for all subtargets and use the ondemand governor.
Tested bcm2708 on RPi0W. Tested bcm2709 and bcm2710 on RPi3.
Reported-by: Bryan Mayland <bmayland@capnbry.net>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The generic SPI code calculates how long the issued transfer would take
and adds 100ms in addition to the timeout as tolerance. On my 500 MHz
Lantiq Mips SoC I am getting timeouts from the SPI like this when the
system boots up:
m25p80 spi32766.4: SPI transfer timed out
blk_update_request: I/O error, dev mtdblock3, sector 2
SQUASHFS error: squashfs_read_data failed to read block 0x6e
After increasing the tolerance for the timeout to 200ms I haven't seen
these SPI transfer time outs any more.
The Lantiq SPI driver in use here has an extra work queue in between,
which gets triggered when the controller send the last word and the
hardware FIFOs used for reading and writing are only 8 words long.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refresh patches. A number of patches have landed upstream & hence are no
longer required locally:
062-[1-6]-MIPS-* series
042-0004-mtd-bcm47xxpart-fix-parsing-first-block
Reintroduced lantiq/patches-4.4/0050-MIPS-Lantiq-Fix-cascaded-IRQ-setup
as it was incorrectly included upstream thus dropped from LEDE.
As it has now been reverted upstream it needs to be included again for
LEDE.
Run tested ar71xx Archer C7 v2 and lantiq.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
[update from 4.4.68 to 4.4.69]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This model also contains few partitions non-discoverable partitions we
need to "protect". Othen than that it uses non-deprecated serial entry
in DTS that doesn't work with LEDE so we need to workaround it as well.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
