The eth5 LED on the RB2011 is not working because the
LED control rule is missing. Fix it.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39335
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Patchwork: http://patchwork.openwrt.org/patch/4689/
[juhosg:
- remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all,
- change subject and update the commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39214
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4688/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39213
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.
Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39149
Now that the switch is working correctly I had the chance to actually
test the LED config.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39129
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.
This fix implements just that.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39128
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39126
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39102
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: use a separate patch for kernel changes]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39077
The TL-WA801ND v2 board has only one LAN port which makes
it more similar to the TL-WR[78]50RE devices. Move the
board setup code into the mach-tl-wax50re.c file.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39072
This way it is a bit easier to add other TP-LINK devices based on the
Atheros AP123 reference board with one LAN port.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39071
Patch to add kernel support for the TP-LINK WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4500/
[juhosg:
- the TL-WA801ND v2 does not have a sliding switch, it uses a push button
for WPS instead. Use the tl_mr3420v2_gpio_keys array to reflect that,
- rename kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39063
This patch improves support for the device considerably.
1. The wifi didn't work in the initial release. This was because
the WMAC of the AR9340 is not connected to the antennas.
(However, it can pick up wifi signals, if they are strong enough!)
Instead there's a dedicated AR9300 chip on the same board, which
works.
2. Ethernet throughput is improved. iperf shows that the hardware
can sustain more than 200Mbit/s and no longer drops any packages
when the link is under load.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4461/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38949
Just a small oversight my part, added the support for the USB led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4425/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38946
Patch to add kernel support for the TP-LINK WA750RE and the WA850RE
range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
[juhosg: rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38717
This patch adds a new device definition for a
Western Digital device. The hardware seems to
be based on Qualcomm Atheros DB120 design.
Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg: refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38686
BXU2000n-2 A1 is a BHU Networks WLAN board, use ar9341 chip.
Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
- rename and refresh kernel patch,
- fix some checkpatch warnings and adjust whitespaces in
mach-bhu-bxu2000n2-a.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38591
This patch adds support for DRAGINO2 board (used by
Meshpotato v2). Most of the files included can be
found in the official svn repository provided by the
company [1]. I have just adapt it to the last OpenWrt
trunk revision (Fri Oct 4 10:49:47 2013).
1. http://svn.dragino.com/dragino2
Patchwork: http://patchwork.openwrt.org/patch/4234/
Signed-off-by: Pau Escrich <p4u@dabax.net>
[juhosg:
- rename and refresh kernel patch,
- fix checkpatch warnings in mach-dragino2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38587
Fixes the 5 GHz LED.
The same function has no effect on the 2.4 GHz LED at all, so we might
as well remove it.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38482
This patch adds support for the hardware slide switch on
the TL-MR3040 v2.
Signed-off-by: Mads Hansen <d@taba.se>
[juhosg: use EV_SW instead of EV_KEY]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38190
This patch
- changes the color names from orange to amber
- changes the name of GPIO 13 from WIFI_BGN (wifi_bgn) to WLAN_2G
(wlan2g) to be more consistent with the other routers' files
- changes the descriptions of the hardware keys to be a tad more
explicit
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4081/
[juhosg: update the LED migration script as well]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38105
Enable GPIO 20. This hands off control of the blue planet led to the
integrated switch. Consequently, remove the led configuration for the
blue planet led.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4080/
[juhosg: whitespace fixup]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38096
