The mips reloc patch introduced new allocations which were done before
add_unformed_module but never freed them in case of an error. A new hook in
Linux 3.19 called module_arch_freeing_init can be used for freeing memory
which were allocated during this init phase.
The problem can be seen when trying to load a module (via busybox insmod)
when it was already loaded.
free -m
for i in `seq 1 100`; do
/sbin/insmod /lib/modules/*/ath9k.ko >& /dev/null
done
free -m
This simple loop would leak ~3.2 MB.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46247
Backport for the Spansion S25FL164K
It's a 8 MiB flash chip with 4 KiB erase sectors.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46237
This is useful if the device also has an ethernet WAN interface with a
separate mac address (that is derived from the LAN mac address).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46220
Some machtypes were dropped when 4.0 support was added, and the
incomplete patch was taken over to 4.1.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46187
Code calling fpu_emulator_cop1Handler will pass on fault_addr, making gcc
complain about it not being initialized when the FPU emulator is disabled.
Fixes:
arch/mips/kernel/traps.c: In function 'do_fpe':
arch/mips/kernel/traps.c:864:22: error: 'fault_addr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
process_fpemu_return(sig, fault_addr, fcr31);
^
arch/mips/kernel/traps.c: In function 'do_ri':
arch/mips/kernel/traps.c:806:22: error: 'fault_addr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
process_fpemu_return(sig, fault_addr, fcr31);
^
arch/mips/kernel/traps.c:763:15: note: 'fault_addr' was declared here
void __user *fault_addr;
^
arch/mips/kernel/traps.c: In function 'do_cpu':
arch/mips/kernel/traps.c:1421:28: error: 'fault_addr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (!process_fpemu_return(sig, fault_addr, fcr31) && !err)
^
cc1: all warnings being treated as errors
make[7]: *** [arch/mips/kernel/traps.o] Error 1
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46184
The position of the nvram header file on brcm47xx changed with kernel
version 4.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46170
Make some network uapi headers detect if they are included after
not only glibc but also musl headers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46161
Boot tested: http://pastebin.com/L6aAb9xj
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo:
update to 4.1 final
add patches added since submission
delete patches applied in later rcs
restore commit messages in 220-gc-sections and 304-mips_disable_fpu
fix 050-backport_netfilter_rtcache to match new API
update inlined dma ops with upstream changes
add missing config symbols
enabled CONFIG_MULTIUSER
update kmod defintions for 4.1
]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46112
On two tested devices: Netgear R6250 (BCM53011 rev 2) and Luxul XWC-1000
(BCM53011 rev 3) it was possible to use port 7 and eth1 (instead of port
5 and eth0). It seems BCM53011 just like BCM53012 has 8 ports and
usually 3 of them are connected to the SoC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46104
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45970
On device reset the sizes for the vlan and port tables were wrongly
calculated based on the pointer size instead of the struct size. This
causes buffer overruns on 64 bit targets, resulting in panics.
Fix this by dereferencing the pointers.
Reported-by: Fedor Konstantinov <blmink@mink.su>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45938
At least on my b53 chip, the mask is 3 bits wide, and because
of this some STP states are not set properly and discarded when read.
Maybe for some other chips it makes sense to have just 2 bits width,
but I don't have other versions around to test/validate.
If that's the case then maybe we could add another STP state mask.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45937
STMMAC_PLATFORM and STMMAC_PCI have been added recently in the kernel,
but show up only when STMMAC driver is enabled. So se'll add it in the
generic config, so the kernel build doesn't stall whenever we enable
this driver.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45828
With this patch the following two patches are backported:
* bridge: fix parsing of MLDv2 reports
* bridge: allow setting hash_max + multicast_router if interface is down
The former one is an important fix which got just applied to the net-tree
and is queued for stable. The latter is a patch which is needed to make
the hash_max and multicast_router attributes configurable through
netifd.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 45783
Update kernel sources and refresh some patches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45761
Commit 5168c9a5702648eb690d32ec821647aca80aeba9 introduced a regression
during patch application on the 4.0 kernel. Some of the patched content
doesn't match the actual code, therefore leading to the following error:
Applying patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch
patching file net/ipv6/ip6_output.c
Hunk #1 FAILED at 886.
1 out of 1 hunk FAILED -- rejects in file net/ipv6/ip6_output.c
patching file net/ipv6/route.c
Hunk #1 succeeded at 2247 (offset 2 lines).
Patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch does not apply (enforce with -f)
This change just adapts the actual patch to fix what is in kernel 4.0
and make it apply cleanly.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45705
This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports
5, 7 and 8 connected to Ethernet interfaces:
vlan1ports=0 1 2 3 5 7 8*
vlan2ports=4 8u
Port 6 seems to be always disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45676
Since the kernel/rootfs split handling was modified 2 years ago by r37283 (
https://dev.openwrt.org/changeset/37283 ) and by the subsequent checkins,
users have seen rather scary mtd errors in the log at every boot. The message
ends "-- forcing read-only", which looks a bit error-like. That error has
been mentioned in some forum threads, when users have noticed this message
instead of some actual error.
[ 2.940000] 0x000000070000-0x000000ff0000 : "firmware"
[ 2.970000] 2 netgear-fw partitions found on MTD device firmware
[ 2.970000] 0x000000070000-0x000000188440 : "kernel"
[ 2.980000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 2.990000] 0x000000188440-0x000000ff0000 : "rootfs"
The patch removes the rather useless warning message.
signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45669
This option has been added in kernel 3.17. It shows-up only when both
ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default
to avoid stalling the build when these conditions are met.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45658
