This patch adds the help tool wpan-ping to test the 6LoWPAN
network to help the user debug network problem.
Signed-off-by: Yunhui Fu <yhfudev@gmail.com>
removed copying of binaries to BIN_DIR during install and using
default/install to install binaries to BIN_DIR folder.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Added sama5 to BUILD_SUBTARGET variable.This will populate at91bootstrap
menu options in bootloader menu only when SAMA5 devices are selected as
SUBTARGET and to avoid showing up this menu when legacy device is
selected as SUBTARGET and fixed typo mistake: sama5d3 -> sama5d2.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
This fixes the following problems:
* Add BUILD_DEVICES for legacy subtarget
* Use features from u-boot.mk for sama5 subtarget This is mainly done
by changing the prefix from uboot to U-Boot. This makes them depend
on the sama5 subtarget and not selectable for the legacy subtarget
any more
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Revert an accidental change that was introduced by having an old version
of the patch in my git tree, which was merged in 609208597b
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch adds a parser for the uci representation of
dnsmasq's "-a | --listen-address" option.
In summary, this option forces dnsmasq to listen on the
given IP address(es). Both interface and listen-address
options may be given, in which case the set of both
interfaces and addresses is used.
Note that if no interface option is given, but listen_address is,
dnsmasq will not automatically listen on the loopback interface.
To achieve this, the loopback IP addresses, 127.0.0.1 and/or ::1
must be explicitly added.
This option is useful for ujailed dnsmasq instances, that would
otherwise fail to work properly, because listening to the
"This host on this network" address (aka 0.0.0.0 see rfc1700 page 4)
may not be allowed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (PKG_RELEASE increase)
e781569 update to latest mac80211/cfg80211 API changes
37654d7 mt76x2: fix tx status ampdu length corner case
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This backports a patch from kernel 4.14 to the ath10k-ct version based
on kernel 4.13.
Some devices are using a user space script to load the calibration data
from the flash and this was not trigged any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This should help ath10k work on systems with little or no IOMMU
memory. apu2 can boot two 9888 NICs now, for instance. From
upstream patch by Adrian Chadd.
And, start building the 4.13 based CT ath10k driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Changes since last LEDE release include:
* Fix key-setting bug that broke sending the EAPOL 2/4 in some cases. This was a
bug I introduced some time back while trying to fix .11r and simplify the key
handling logic. (Patch to wpa_supplicant fixed the race with sending the 4/4
and setting the key...un-patched supplicant will still have this race and the 4-way
auth will not work as reliably.)
* Increase amount of active-tids that can be scheduled. This fixes a tx-stall
seen with many station vdevs.
* Fix bug in upstream code that would cause the maximum peer to never be scheduled
for tx.
Signed-off-by: Ben Greear <greearb@candelatech.com>
If you unplug a QMI device, the /dev/cdc-wdmX device
disappears but uqmi will continue to poll it endlessly.
Then, when you plug it back, you have 2 uqmi processes,
and that's bad, because 2 processes talking QMI to the
same device [and the same time] doesn't seem to work well.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
There have been a number of interesting fixes in conntrack-tools since
the current latest release. Most notable is that this fixes IPv6
conntrack table syncing when cross-compiling conntrack-tools.
7e7748d src/main: refresh help message
fe32043 conntrackd.8: refresh file
47a4dda conntrackd.8: add reference to systemd
0cfe7ff doc/manual: include some bits about init systems
74a418b conntrackd: cthelper: ftp: Set match offset/len for PORT mangling
d833bed conntrackd: cthelper: ftp: Fix debug print
dd4b5a1 conntrackd: cthelper: Add new mdns helper
498d698 Link nfct and helper modules with `-z lazy`
9e94e85 sync-mode: print errno message on failure
ab81c35 log: print messages to stdout/sderr if running in console mode
631d92b log: introduce a mechanism to know if log was initialized
ccb1c8b conntrackd: replace error reporting in the config parser with dlog()
bee121e conntrackd: replace fprintf calls with dlog()
5a51b04 conntrack-tools: update Arturo Borrero Gonzalez email address
abb9984 helper: remove copy and paste from uapi kernel header
a91a004 src: add log message when resync is requested by other node
c2d8be1 systemd: fix missing log.h include
f6ca216 config: drop old/obsolete/deprecated conntrackd.conf config options
8b83771 conntrack: send mark filter to kernel iff set
1ba5e76 conntrackd: cthelper: Don't leak nat_tuple
832166d conntrackd: cthelper: Free pktb after use
ff843bc conntrackd: config: Do not strdup() tokens
b61c454 conntrackd: cthelper: ssdp: Track UPnP eventing
8ea394e conntrackd: Remove obsolete rule to catch ambiguous Checksum option
39398cd conntrackd: CommitTimeout breaks DisableExternalCache set On
29b390a conntrack: Support IPv6 NAT
381827a conntrackd: factorice tx_queue functions
131df89 conntrackd: factorize resync operations
d31bacc conntrackd: consolidate more code to use resync_send()
3d98496 conntrackd: request resync at startup
ef410bf conntrackd: remove use of HAVE_INET_PTON_IPV6
9d38445 conntrackd: evaluate configuration earlier
6feded7 conntrackd: cleanup if failed forking
dbfdea7 conntrackd: deprecate unix backlog configuration
210f542 conntrackd: make the daemon run in RT mode by default
37cc7f0 conntrackd: remove warning for -S
d2849d1 conntrack: Show multiple CPUs stats from proc
bc0b49a conntrackd: cthelper: ssdp: fix build with musl
0c77a25 tests: don't fail on modprobe since the driver might be built-in
eefe649 conntrack.8: refresh manpage
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
In order to build conntrack-tools from git, a newer version of
libnetfilter_conntrack is required. As 1.0.6 is currently the latest
release, switch to git.
b0a7cf7 include: expose a copy of nf_conntrack_common.h
f68f7b3 conntrack: fix missing break in setobjopt_undo_dnat()
79dac5a conntrack: revert getobjopt_is_nat() condition
b266523 libnetfilter_conntrack: bump version to 1.0.7
e870432 labels: don't crash on NULL labelmap
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
b39cac7 src: Correct typo in the location of internal.h in #include
58cb066 src: Declare the define visibility attribute together
e84b559 Revert "src: Declare the define visibility attribute together"
003c2b1 examples: set dummy connmark value to show use of NFQA_CT nested attribute
63973da doc: extend the doxygen section about NFQA_CFG_F_GSO
d7f74c7 build: bump version to 1.0.3
3f9eb57 build: bump library release version too
601abd1 doc: Add information about retrieving UID/GID/SECCTX fields
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
As git.netfilter.org seems to support HTTPS, use that instead of HTTP
which is insecure, or GIT which is blocked on many corporate networks.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
NXP Layerscape LSDK had set up its own open source web site
and github for release.
https://lsdk.github.iohttps://github.com/qoriq-open-source
This patch is to update rcw/fman_ucode/u-boot packages with LSDK
git trees. Also add some patches of packages to support LEDE.
Since ARMv8 32-bit u-boot images are same with ARMv8 64-bit images
but 64-bit toolchain couldn't be used for 32-bit targets, we still
use a private tree for ARMv8 32-bit u-boot images. This is in plan
to move this private tree to NXP Layerscape github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Rename subtargets 32b/64b with armv8_32b/armv8_64b which are
more proper, and update makefile files. There also will be other
subtargets added in the future, like armv7.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The nghttp2 library is an implementation of the Hypertext Transfer
Protocol version 2 in C; it supports RFC7540 and RFC7541.
The package enables only the reusable C library; binary size is 130K (X86)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This patch implements CPU frequency control as found on several
routerboard devices.
Supported SoCs:
- QCA953X
- AR9344
Tested on hAP lite and mAP lite (QCA953x): steps of 50MHz
Tested on LHG 5 (AR9344): steps of 50MHz
On unsupported hardware, this patch is a NOP: it will not alter the
new field.
"rbcfg help" will display an empty "cpu_freq" help listing.
"rbcfg show" will not show the cpu_freq field.
"rbcfg set/get cpu_freq" will return an error code.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
[adjusted subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
A recent commit in hostapd added a build option to specify the default
TLS ciphers. This build option is passed via CFLAGS. Due to the way
CFLAGS are handled when building wpad, the compiler tries to recursively
expand TLS_DEFAULT_CIPHERS, resulting in the following error:
../src/crypto/tls_openssl.c: In function 'tls_init':
<command-line>:0:21: error: 'DEFAULT' undeclared (first use in this function)
../src/crypto/tls_openssl.c:1028:13: note: in expansion of macro 'TLS_DEFAULT_CIPHERS'
ciphers = TLS_DEFAULT_CIPHERS;
^
Escape double quotes in the .cflags file to avoid this.
Fixes: 2f78034c3e ("hostapd: update to version 2017-08-24")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
5df3f01 config: suppress error if no wireless config present (FS#1030)
3429bd8 system-linux: add support for hotplug event 'move'
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
632688e utils: nuke bitfield functions and macros
f714be1 uloop: make SIGCHLD signal handling optional
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The module fails to compile with falcon. Remove the falcon depends from
the module to not (try to) compile it for falcon any longer.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Albeit ltq-ptm is supported on AmazonSE, the package fails to compile.
Mark the AmazonSE variant as broken to not mark it unnecessary harder
to fix (and test) the compile error.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following features are working and tested:
* both Ethernet ports
* MMC
* LED
The following features are not working:
* Wifi (There is a crappy driver we could port)
* SPI flash (I haven't looked into this)
I haven't tried out the rest.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Including linux/interrupt.h in linux/hrtimer.h causes this error message
on PowerPC builds on x86, ARM and MIPS it works:
CC [M] /backports-4.14-rc2-1/compat/main.o
In file included from /backports-4.14-rc2-1/backport-include/linux/printk.h:5:0,
from ./include/linux/kernel.h:13,
from /backports-4.14-rc2-1/backport-include/linux/kernel.h:3,
from ./include/linux/list.h:8,
from /backports-4.14-rc2-1/backport-include/linux/list.h:3,
from ./include/linux/module.h:9,
from /backports-4.14-rc2-1/backport-include/linux/module.h:3,
from /backports-4.14-rc2-1/compat/main.c:1:
./include/linux/ratelimit.h: In function 'ratelimit_state_exit':
./include/linux/ratelimit.h:62:11: error: dereferencing pointer to incomplete type 'struct task_struct'
current->comm, rs->missed);
^
./include/linux/printk.h:279:37: note: in definition of macro 'pr_warning'
printk(KERN_WARNING pr_fmt(fmt), ##__VA_ARGS__)
^
./include/linux/ratelimit.h:61:3: note: in expansion of macro 'pr_warn'
pr_warn("%s: %d output lines suppressed due to ratelimiting\n",
^
The backport of the hrtimer_start() functions needs the
linux/interrupt.h because some parts are defined there. Fix this by
moving the hrtimer_start() backport to the linux/interrupt.h backport
header file.
Fixes: a8f63a0717: ("mac80211: update to backports-4.14-rc2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates mac80211 to backprots-4.14-rc2.
This was compile and runtime tested with ath9k, ath10k and b43
with multiple stations and ieee80211w and in different scenarios by many
other people.
To create the backports-4.14-rc2-1.tar.xz use this repository:
https://git.kernel.org/pub/scm/linux/kernel/git/backports/backports.git
from tag v4.14-rc2-1
Then run this:
./gentree.py --git-revision v4.14-rc2 --clean <path to linux repo> ../backports-4.14-rc2-1
This also adapts the ath10k-ct and mt76 driver to the changed cfg80211
APIs and syncs the nl80211.h file in iw with the new version from
backports-4.14-rc2.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The /bin/config_generate script and some other scripts are assuming the
/etc/config directory exists in the image. This is true in case for
example the package firewall, dropbear or dnsmasq are included, which
are adding the files under /etc/config/. Without any of these package
the system will not boot up fully because the /etc/config/ directory is
missing and some init scripts just fail.
Make sure all images with the base-files contain a /etc/config/
directory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <john@phrozen.org>
This reverts commit b428f45c062dc8ca8c2f35f491fa467dc5b85519.
If the optimized firmware download is disabled, the xdsl subsystem
hangs in the "idle request" state after physically disconnecting and
reconnecting the xdsl modem from the line.
It might fix the failing line init on boot as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The empty version.sh script causes a problem when run by make:
make[3]: /usr/bin/env bash: Shell program not found
Adding a shebang line in version.sh seems to solve it.
Fixes FS#977.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
getrandom blocks until the random pool is being initialized.
Unfortunately, this code is being called early during init to create the
overlay filesystem, on some devices leaving little chance for a
successful random pool init.
True randomness is not that important here, so fix this issue by
sticking to using /dev/urandom, like in older versions of this code.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add -static-libstdc++ to TARGET_LDFLAGS to avoid a hard dependency on
libstdc++, and -Wl,--gc-sections to further reduce the size on platforms
that support it.
Fixes CVE-2017-9778.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is useful for tuning some more exotic parameters where it doesn't
make sense to attempt to cover everything in uci directly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adds config option to enable compression support which is usefull
when using a terminal sessions over a slow link. Impact on binary
size is negligible but additional 60 kB (uncompressed) is needed for
a shared zlib library.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
b84fdac Add debug output for service_timeout
8f7e3bc Remove incorrect comma in http service json config
9f40133 Remove ttl==255 restriction for queries
Signed-off-by: John Crispin <john@phrozen.org>
ee582d1 instance: properly compare and reload respawn config
260a4cd utrace: Start the tracee only after uloop initialization
520ad3c utrace: Switch all logging to ulog
1c48104 utrace: Support non-contiguous syscall numbers
582cf97 utrace: Forward SIGTERM to the traced process
32534f7 utrace: Report ptrace errors
ccde3fb seccomp: Improve error message
7f9b174 preload-seccomp: Use proper log level for error messages
e3c4302 Start seccomp-enabled services via seccomp-trace
5e4ad02 seccomp: Log seccomp violations with utrace
2661b2f utrace: Use PTHREAD_SEIZE instead of PTHREAD_TRACEME
b5d53c6 utrace: Deliver signals to traced processes
b416ed9 utrace: Support tracing multi-threaded processes and vfork
8b7d47a utrace: Trace processes across forks
c6b6ec6 utrace: Sort syscalls by number of invocations
592c532 Update trace attribute
c8faedc Do not disable seccomp when configuration is not found
017f3a1 utrace: Fix off-by-one errors
5acaf15 utrace: Fix environment initialization
Signed-off-by: John Crispin <john@phrozen.org>
This commit improves support for the Xiaomi Mi Router 3G originally
added in commit 6e283cdc0d
Improvements:
- Remove software watchdog as hardware watchdog now working as per
commit 3fbf3ab44f for all mt7621
devices.
- Reset button polarity corrected - length of press determines reboot
(short press) vs. reset to defaults (long press) behaviour.
- Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit
link and blink on activity. Green LEDs driven directly by switch
indicating any link speed and tx activity.
- USB port power on/off GPIO exposed as 'usbpower'
- Add access to uboot environment settings for checking/setting uboot
boot order preference from user space.
Changes:
- Front LED indicator is physically made of independent Yellow/Amber,
Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel
indicator, hence the colour behaviour is similar to an RGB LED. RGB
LEDs are not supported at this time because they produce colour results
that do not then match colour labels, e.g. enabling 'mir3g:red' and
'mir3g:blue' would result in a purple indicator and we have no such
label for purple.
The yellow, red & blue LEDs have been split out as individual yellow,
red & blue status LEDs, with yellow being the default status LED as
before and with red's WAN and blue's USB default associations removed.
- Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan
layout. eth0.1 is LAN, eth0.2 is WAN
- Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet
leakage between kernel switch init and uci swconfig
uboot behaviour & system 'recovery'
uboot expects to find bootable kernels at nand addresses 0x200000 &
0x600000 known by uboot as "system 1" and "system 2" respectively.
uboot chooses which system to hand control to based on 3 environment
variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed
last_success represents a preference for a particular system and is set
to 0 for system 1, set to 1 for system 2. last_success is considered *if*
and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either*
failed flags are set then uboot will attempt to hand control to the
non failed system. If both failed flags are set then uboot will check
the uImage CRC of system 1 and hand control to it if ok. If the uImage
CRC of system is not ok, uboot will hand control to system 2
irrespective of system 2's uImage CRC.
NOTE: uboot only ever sets failed flags, it *never* clears them. uboot
sets a system's failed flag if that system's was selected for boot but
the uImage CRC is incorrect.
Fortunately with serial console access, uboot provides the ability to
boot an initramfs image transferred via tftp, similarly an image may
be flashed to nand however it will flash to *both* kernels so a backup
of stock kernel image is suggested. Note that the suggested install
procedure below set's system 1's failed flag (stock) thus uboot ignores
the last_success preference and boots LEDE located in system 2.
Considerable thought has gone into whether LEDE should replace both
kernels, only one (and which one) etc. LEDE kernels do not include a
minimal rootfs and thus unlike the stock kernel cannot include a
method of controlling uboot environment variables in the event of
rootfs mount failure. Similarly uboot fails to provide an external
mechanism for indicating boot system failure.
Installation - from stock.
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: nvram set flag_try_sys1_failed=1
- run: nvram commit
- run: reboot
Recovery - to stock.
Assuming you used the above installation instructions you will have a
stock kernel image in system 1. If it can be booted then it may be used
to perform a stock firmware recovery, thus erasing LEDE completely. From
a 'working' LEDE state (even failsafe)
Failsafe only:
- run: mount_root
- run: sh /etc/uci-defaults/30_uboot-envtools
Then do the steps for 'All'
All:
- run: fw_setenv flag_try_sys2_failed 1
- run: reboot
The board will reboot into system 1 (stock basic kernel) and wait with
system red light slowly blinking for a FAT formatted usb stick with a
recovery image to be inserted. Press and hold the reset button for
around 1 second. Status LED will turn yellow during recovery and blue
when recovery complete.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
With ltq-vdsl-mei 1.5.17.6 an optimized firmware download was added and
enabled by default. As soon as the optimized firmware download is
enabled, a watchdog based reboot is trigger between 24h to 48h of
uptime if the board isn't connected to a xdsl line.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a backport form drv_dsl_cpe_api-4.18.10 and fixes some PM
thread handling issues which lead to high system load and watchdog
trigger within 1h of uptime for boards not connected to a xdsl line.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Fixes CVE-2017-12166: out of bounds write in key-method 1.
Remove the mirror that was temporarily added during the
2.4.3 release.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Update the config file to the latest version.
Added CONFIG_EAP_FAST=y because it was the only
missing flag about EAP compared to full config.
Removed NEED_80211_COMMON flag because it is not part
of config file, it is set by the hostapd upstream Makefile.
Other flags are the same as before.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Removed NEED_80211_COMMON flag because it is not part
of config file, it is set by the hostapd upstream Makefile.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Commented CONFIG_IEEE80211W=y flag because it is
set in the Makefile, only if the driver supports it.
Removed NEED_80211_COMMON flag because it is not part
of config file, it is set by the hostapd upstream Makefile.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Removed flag CONFIG_WPS2 because it is no more
needed due to this changelog (2014-06-04 - v2.2):
"remove WPS 1.0 only support, i.e., WSC 2.0
support is now enabled whenever CONFIG_WPS=y is set".
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Bump to 7.55.1 broke the disable threaded resolver feature as reported
in https://github.com/curl/curl/issues/1784.
As a result curl is always compiled with the threaded resolver feature
enabled which causes a dependency issue on pthread for uclibc.
Fix this issue by backporting the upstream curl commit which fixes
disable threaded resolver.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Fixes the following build issue: "undefined reference to `EVP_MD_CTX_create'"
From: Jelle van der Waa <jelle@vdwaa.nl>
The rsa_st struct has been made opaque in 1.1.x, add forward compatible
code to access the n, e, d members of rsa_struct.
EVP_MD_CTX_cleanup has been removed in 1.1.x and EVP_MD_CTX_reset should be
called to reinitialise an already created structure.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[replaced u-boot patch with original version from u-boot git]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This will allow you to build and package the uas.ko module.
With more routers supporting USB 3.0 host this could help
speed up activities like DLNA and Samba, as well as reduce
CPU utilization over BOT mass storage drivers.
Signed-off-by: James Christopher Adduono <jc@adduono.com>
3fd58e9 2017-08-19 uhttpd: add manifest support
88c0b4b 2017-07-09 file: fix basic auth regression
99957f6 2017-07-02 file: remove unused "auth" member from struct
path_info
c0a569d 2017-07-02 proc: expose HTTP_AUTH_USER and HTTP_AUTH_PASS
ad93be7 2017-07-02 auth: store parsed username and password
fa51d7f 2017-07-02 proc: do not declare empty process variables
a8bf9c0 2017-01-26 uhttpd: Add TCP_FASTOPEN support
e6cfc91 2016-10-25 lua: ensure that PATH_INFO starts with a slash
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
The arm-trusted-firmware-sunxi package is only used by the Allwinner
A64, so only make it selectable for its subtarget sunxi/cortexa53.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
at91bootstrap is a second-level bootloader for Microchip(Atmel AT91) SoCs.
It provides a set of algorithms to manage the hardware initialization and
to download the main application or a third-level bootloader(i.e. uboot)
from specified boot media to main memory and execute it.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D4 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D2 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D3 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
This option is used to specify a file containing PEM certs, to complete the
local certificate chain. Which is quite usefull for "split-CA" setups.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Add support for ft_psk_generate_local flag in ieee80211r
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[original author]
Signed-off-by: Sergio <mailbox@sergio.spb.ru>
Instead of manually downloading the files again we can also take the
same files directly from the ath10k-firmware git which was cloned
before.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Init script won't append --no-dhcp-interface option if interface
protocol is one of: ncm, directip, qmi, mbim.
This is caused by IP address assigned to dynamically created netifd
interfaces. As a result there's no netmask assigned to the main
interface and dhcp_add() function returns prematurely.
By moving network subnet check we can ensure that --no-dhcp-interface is
properly generated for wwan interfaces.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase; move network checks]
Setting ipv6 to auto in case of a pppoe interface will trigger the
creation of a dynamic wan_6 interface meaning two IPv6 interfaces
(wan6 and wan_6) will be active on top of the pppoe interface.
This leads to unpredictable behavior in the network; therefore set
ipv6 to 1 which will prevent the dynamic creation of the wan_6
interface.
Further alias the wan6 interface on top of the wan interface for pppoe
as the wan6 interface can only be started when the link local address is
ready. In case of pppoe the link local address is negotiated during the
Internet Protocol Control Protocol when the PPP link is setup meaning
all the IP address info is only available when the wan interface is up.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
