The EEPROM data in the flash of the ARV7518PW, ARV8539PW22,
BTHOMEHUBV2B and BTHOMEHUBV3A is stored byte-swapped (swab16), meaning
that for example the ath9k base_eep_header fields "version" (high and
low byte), "opCapFlags" and "eepMisc" are swapped (the latter ones are
just 1 byte wide, thus their position is swapped).
The old "ath,eep-endian" property enabled the corresponding swapping
logic in the ath9k driver (swab16 in ath9k_hw_nvram_swap_data, which is
based on the magic bytes in the EEPROM data which have nothing to do
with the calibration data - thus this logic should not be used
anymore).
Since we have switched to the upstream ath9k devicetree bindings there
is no binding anymore which enables swab16 in ath9k (as this logic is
not recommended anymore as explained above), leading to ath9k
initialization errors:
ath: phy0: Bad EEPROM VER 0x0001 or REV 0x00e0
(this shows that the version field is swapped, expected values are VER
0x000E and REV 0x0001)
Swapping the ath9k calibration data when extracting it from the flash
fixes the devices listed above (all other devices do not require
additional swapping, since the position of the fields is already as
expected by ath9k). This allows ath9k to read the version correctly
again, as well as the more important "eepmisc" field (which is used for
determining whether the data inside the EEPROM is Big or Little Endian
which is required to parse the EEPROM contents correctly).
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Rob suggested I should use of_machine_is_compatible insteak of a new
property and updated patch has been sent.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Correct splitting the 32-bit 'hostid' value to two 16-bit hexadecimal
values. Previously, the lower 16-bit value was truncated to an 8-bit
value, which would result in hostid values 100 and 200 both to be set
to [::0:0] instead of [::0:100] and [::0:200] respectively.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
If the hostname in /etc/config/system is modified the dnsmasq will not
reread the update host file under /tmp/hosts/dhcp.$cfg.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Last release of libnetfilter-queue was in 2012.
There don't seem to be any release tarballs since then.
This updates it to a more recent version, pointing to the git repo.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This is helpful for Orion-based NAS boxes that have the XOR engine enabled
since it provides faster software RAID.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The harddisk target is for NAS boxes, so set the DEVICE_TYPE accordingly so we
get a sensible default package selection.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable support for this machine in the kernel and also produce valid image
files with the correct machine id.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Utilize the existing git download logic from include/download.mk and migrate
the kernel download over to it. This avoids repeatedly cloning kernel sources
after a make target/linux/clean for instance.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [fix build error]
This is going to be used to migrate the hand rolled git clone for the kernel
into using the git download method. The kernel uses custom options that we may
have to pass down.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Needed to work around ethernet hang issues on Ubiquiti NanoStation Loco XW,
because ar71xx is not converted to device tree yet.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
By default, forwarding between all ports is allowed on init. This is
problematic in cases where some ports are supposed to be isolated from
each other, most commonly LAN/WAN separation.
REG_ESW_PORT_PCR(port) has a destination mask for a particular port,
controlling what other ports it is allowed to send packets to.
Instead of initializing all to 0xff (all ports), allow each physical
port to send to the CPU port, and the CPU port to send to all other
ports.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.
Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.
Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
sysupgrade command fails due to missing U-Boot environment-processing
binaries on sysupgrade ramdisk. The missing binaries result in the
following output:
Switching to ramdisk...
Performing system upgrade...
ash: /usr/sbin/fw_printenv: not found
ash: fw_setenv: not found
ash: touch: not found
cannot find target partition
Signed-off-by: Vignesh Balasubramaniam <vigneshb.hp@gmail.com>
The name from the Device define will be used in the metadata. Due to
typo/different spelling, this name might not match the one exported in
/lib/mvebu.sh.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes the following security problems:
CVE-2016-7440: Software AES table lookups do not properly consider cache-bank access times
CVE-2016-7439: Software RSA does not properly consider cache-bank monitoring
CVE-2016-7438: Software ECC does not properly consider cache-bank monitoring
SWEET32 Attack
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support for MIPS toolchains without FPU support was added upstream,
so remove our patch.
patches/310-mips-link-tool.patch was a backport form this version of valgrind
src/abort.c is not referenced anywhere
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the following security problems:
CVE-2016-8615: cookie injection for other servers
CVE-2016-8616: case insensitive password comparison
CVE-2016-8617: OOB write via unchecked multiplication
CVE-2016-8618: double-free in curl_maprintf
CVE-2016-8619: double-free in krb5 code
CVE-2016-8620: glob parser write/read out of bounds
CVE-2016-8621: curl_getdate read out of bounds
CVE-2016-8622: URL unescape heap overflow via integer truncation
CVE-2016-8623: Use-after-free via shared cookies
CVE-2016-8624: invalid URL parsing with '#'
CVE-2016-8625: IDNA 2003 makes curl use wrong host
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change getver.sh to append a short Git commit hash to the end of the artifical
revision number. This way we still have order- and comparable commit numbers
but also a direct relation to the Git commit.
The new output format will look like "r2400+2-882472e" for dirty trees or like
"r2402-882472e" for clean ones.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
