Commit graph

43 commits

Author SHA1 Message Date
Alberto Bursi
f99178b6c0 kirkwood: cleanup nsa310b mac address extraction
switch nsa310b mac address reading to mtd_get_mac_ascii helper as
it seems the fw_env.config file is created way later than when
network is set up, when I tested I still had that file included
in the image through /files folder.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-02-11 21:16:28 +01:00
Alberto Bursi
94676dd99d kirkwood: add ZyXEL NSA310b
The ZyXEL NSA310 device is a Kirkwood based NAS:

- SoC: Marvell 88F6702 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: Realtek (over pcie)
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II port (1 internal and 1 external)
- 2 USB 2.0 ports (1 front and 1 back)
- Smart fan

The stock u-boot cannot read ubi so it should be replaced with the
LEDE/OpenWRT's u-boot or with a u-boot from here
https://github.com/mibodhi/u-boot-kirkwood

This device's boot ROM supports "kwboot" tool
(in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared)
that sends an uboot image to the board over serial connection, it is very easy to unbrick.

The stock bootloader can use usb and read from FAT filesystems,
so the installation process is simple, place the uboot file on a USB flashdrive
formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL
to the board and write the following commands in the bootloader console:

usb reset
fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin
nand write 0x1000000 0x00000 0x100000
reset

Now you are rebooting in the new u-boot, write this in its console to install the firmware:

usb reset
fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin
nand erase.part ubi
nand write 0x2000000 ubi 0x600000

If your firmware file is bigger than 6 MiBs you should write its size in hex
instead of 0x600000 above, or remove that number entirely (it will take a while in this case).

If you are using another uboot that can read ubi, set mtdparts like this

mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi)

And set your bootcmd to be like this

bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000

Then you can install the firmware as described above.

After you installed (or configured) the u-boot for booting the firmware,
write the device's mac address in the ethaddr u-boot env.
The MAC address is usually on a sticker under the device (one of the two codes is the serial),
it should begin with "107BEF" as it is assigned to ZyXEL.

write in the u-boot console (use your MAC address instead of the example)

setenv ethaddr 10:7B:EF:00:00:00
saveenv

to save the mac address in the u-boot.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-01-24 16:21:25 +01:00
Felix Fietkau
83d59453c0 kirkwood: fix sysupgrade for non-dockstar NAND devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-30 12:58:20 +01:00
Paul Wassi
d2606107ab kirkwood: fix pogo_e02 LED name
The pogo_e02's dts file has its LEDs named "pogo_e02:(...)"
Fix the status-LED's name for this device.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-10-26 12:37:46 +02:00
Paul Wassi
f6b5df44d9 kirkwood: remove redundant code in etc/board.d/02_network
Remove redundant code: merge boards/cases that share
the same network configuration.
Also fix the alphabetical ordering of the cases.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-10-26 12:37:45 +02:00
Mathias Kresin
c1578d4fc9 cleanup ucidef_set_interface* usage
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:32:25 +02:00
Luka Perkov
afa1c47e71 kirkwood/dockstar: use ubi(kernel, squashfs, ubifs) images
The new image requires `bootz` because of devicetree appending.
To flash a new image boot initramfs:

  tftpboot 0x800000 openwrt-kirkwood-dockstar-initramfs-kernel.bin
  bootz 0x800000

  # detach if already attached
  ubidetach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')
  # scp openwrt-kirkwood-dockstar-squashfs-factory.bin /tmp
  ubiformat -f /tmp/openwrt-kirkwood-dockstar-squashfs-factory.bin
  # attach is important to resize rootfs_data otherwise it wont boot
  ubiattach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 49010
2016-03-14 17:06:09 +00:00
Jo-Philipp Wich
67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
Jo-Philipp Wich
08848936dd all: remove redundant board.d/00_model files
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47753
2015-12-04 11:07:06 +00:00
Jo-Philipp Wich
296212c301 kirkwood: add missing board_config_flush(), remove dead code
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47745
2015-12-03 23:13:04 +00:00
Jo-Philipp Wich
80a3e65a9d kirkwood, ipq806x: fix board.d script permissions
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47735
2015-12-03 22:42:13 +00:00
Jo-Philipp Wich
7514b6d73b kirkwood: switch from uci-defaults to board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47733
2015-12-03 22:27:18 +00:00
Luka Perkov
31c7de0313 kirkwood: add diag LED on Linksys EA3500
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47435
2015-11-10 00:16:56 +00:00
Luka Perkov
b0e7ca4f8f kirkwood: support sysupgrade on Linksys EA[34]500
This automatically writes to the alternate firmware partition
(on Linksys's dual firmware layout) using code borrowed from
the WRT1900AC port.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47434
2015-11-10 00:16:42 +00:00
Luka Perkov
ea8ac0999c kirkwood: support Linksys boot counter on EA[34]500
This is done with existing code from the WRT1900AC port.
It makes sure the "auto_recovery" bootloader option is set,
and resets the s_env boot counter after a successful boot.

This gives users without a serial console connection some
measure of safety.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47433
2015-11-10 00:16:37 +00:00
Luka Perkov
ad8f6370de kirkwood: consistently use engineering board names
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47430
2015-11-10 00:16:28 +00:00
Luka Perkov
805492bda9 kirkwood: pogo_e02: use mainline led definitions
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47385
2015-11-04 22:28:42 +00:00
Luka Perkov
6a18146206 kirkwood: add initial support for NSA310s
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47330
2015-11-01 01:13:16 +00:00
Luka Perkov
7437be53ba kirkwood: add support for the Seagate GoflexHome
Add Support for the Seagate GoflexHome <http://wiki.openwrt.org/toh/seagate/goflexhome>

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 45647
2015-05-08 20:12:39 +00:00
Luka Perkov
5cce8f9a0f kirkwood: Seagate GoFlex Net
Add GoFlex Net "Board Name" , set and cleanup network default and LEDs.
Remove kmod-rtc-marvell from default packages, as the GoFlex net does not have a RTC.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 44422
2015-02-12 14:39:26 +00:00
Luka Perkov
81db848656 targets: base-files: diag.sh does not need to be executable
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44305
2015-02-07 19:58:58 +00:00
Luka Perkov
86f1a60549 kirkwood: drop port-based VLAN setup
Using port-based VLANs depends on a non-standard
swconfig parameter, which compilcates things like
LuCI that don't know about it. This patch changes
the default to use 802.1q VLANs internally in the
switch, but without tagging packets since we have
two Ethernet ports.

iperf3 tests indicate no difference in performance
versus port-based VLANs when the CPU port is not
using tags.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 44122
2015-01-25 13:11:02 +00:00
Luka Perkov
34f6c6fc38 kirkwood: enable switch on Linksys EA3500
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 44036
2015-01-18 16:45:01 +00:00
John Crispin
8698398a6e target: kirkwood: fix leds defaults config
Fix missing parameters in 01_leds

Signed-off-by: Gerald Kerma <dreagle@doukki.net>

SVN-Revision: 44007
2015-01-17 14:39:01 +00:00
Luka Perkov
873202fc0b kirkwood: add *plugs to uci-defaults
Set defaults health led to a timer heartbeet (200/800)
and populate network for:

- GuruplugServerPlus
- SheevaPlug
- SheevaPlug with eSATA

Signed-off-by: Gerald Kerma <dreagle@doukki.net>

SVN-Revision: 43752
2014-12-19 11:05:13 +00:00
Luka Perkov
39743e45f8 kikwood: populate kirkwood.sh with new boards
- SheevaPlug
- SheevaPlug with eSATA
- GuruplugServerPlus

Signed-off-by: Gerald Kerma <dreagle@doukki.net>

SVN-Revision: 43751
2014-12-18 18:38:43 +00:00
Luka Perkov
ec9a0f898a kirkwood: set default EA4500 switch config
This maps the LAN ports to eth0 and WAN port to eth1.
Since there are two interfaces the 802.1q VLAN mode
is unnecessary and left disabled. Port-based VLANs
are used instead.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 43750
2014-12-18 18:38:38 +00:00
John Crispin
019ea725aa add "preinit_regular" diag.sh set_state argument
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 43715
2014-12-15 10:37:00 +00:00
John Crispin
7a65768ddc kirkwood: add a diag script
Currently only Linksys EA4500 is supported.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 43543
2014-12-07 16:53:37 +00:00
Luka Perkov
4f1a9470f0 kirkwood: add support for Linksys EA3500
http://wiki.openwrt.org/toh/linksys/ea3500

Signed-off-by: Dan Walters <dan@walters.io>

SVN-Revision: 43230
2014-11-10 23:55:10 +00:00
Luka Perkov
a54f4320f9 kirkwood: move kirkwood.sh to /lib/ for consistency
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41338
2014-06-26 10:13:47 +00:00
Luka Perkov
8416523dba kirkwood: base-files: use /lib/functions/kirkwood.sh
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41336
2014-06-24 18:18:53 +00:00
Luka Perkov
e6aea925d3 kirkwood: base-files: add script to detect board name and populate /tmp/sysinfo
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41335
2014-06-24 18:18:51 +00:00
Luka Perkov
4122af10f9 kirkwood: add support for Linksys EA4500
Support is added only for kernel 3.14 - do not show it until
the switch is made.

Following uboot env changes are needed to make it work on stock uboot:
2014-05-28 21:43:39 +00:00
Luka Perkov
58fa3f8fdf kirkwood: update support for dockstar
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:

nand erase 0x200000 0xfe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-dockstar-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset

Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-by: Alexander Couzens <lynxis@fe80.eu>
CC: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 39593
2014-02-15 23:53:10 +00:00
Luka Perkov
0c25f159fd kirkwood: update support for iconnect
Previous patch was pushed due to false user report. While at it fix alphabetic
ordering.

The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:

nand erase 0x200000 0x1fe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-iconnect-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset

Signed-off-by: Luka Perkov <luka@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 39591
2014-02-15 23:53:08 +00:00
Luka Perkov
e00bc81a56 kirkwood: add userland support for Pogoplug E02
This patch adds the userland support for the Pogoplug E02 by Cloud
Engines, Inc.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>

SVN-Revision: 38631
2013-10-31 12:04:04 +00:00
Luka Perkov
73246d2f64 kirkwood: upgrade to 3.10.15
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 38402
2013-10-14 19:46:40 +00:00
Steven Barth
ea94d66b0f Adapt default network configuration for IPv6
SVN-Revision: 36278
2013-04-09 08:03:08 +00:00
Jo-Philipp Wich
3a2cccda2e all targets: use numerically prefixed uci-defaults file names to better control order of execution
SVN-Revision: 35217
2013-01-18 12:42:53 +00:00
Luka Perkov
1c80d9f21d kirkwood: fix typo in uci-defaults/leds
Signed-off-by: Martin Mueller <mm@sig21.net>

SVN-Revision: 32343
2012-06-13 18:41:42 +00:00
Gabor Juhos
c81c6516de kirkwood: use the generic uci-default functions for initial LED setup
SVN-Revision: 31994
2012-05-29 16:39:20 +00:00
Gabor Juhos
ba3ad24514 kirkwood: use uci-defaults to configure different boards
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>

SVN-Revision: 31990
2012-05-29 16:39:15 +00:00