Commit graph

40388 commits

Author SHA1 Message Date
Sandeep Sheriker Mallikarjun
c5292989ed uboot-at91: fix build after fpu activation
neon and VFPv4 support is added to this target and uboot-at91 build
fails due to TARGET_CFLAGS -mfloat-abi set to hard. as a fix, setting
uboot-at91 CFLAGS -mfloat-abi=soft.

Fixes: 01cc6bd495 ("at91: sama5: activate fpu")
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-01-09 22:58:49 +01:00
Jo-Philipp Wich
5aabc2cd3d kernel: kmod-w1 depends on kmod-hwmon-core since Linux 4.14
Fixes the following dependency error encountered by the buildbots:

    Package kmod-w1 is missing dependencies for the following libraries:
    hwmon.ko

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-09 22:56:55 +01:00
Mathias Kresin
0674a99f7e kirkwood: sort occurrences of boardame alphabetically
This restores the alphabetical sort that was present
before the renaming of boardname.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Alberto Bursi
0e94df65ca uboot-envtools: add pogoplug v4
add pogoplug v4 envs support in uboot-envtools

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-01-09 22:06:55 +01:00
Alberto Bursi
c19f811c4d kirkwood: add pogoplug v4
also known as
POGO-V4-A3-02
or
POGO-V4-A3-01

SoC: Marvell 88F6192 800Mhz
SDRAM memory: 128MB
Gigabit ethernet: 1 Marvell 88E1310
Flash memory: 128MB
2 status LEDs (one green one red)
1 "Eject" button on the back (used as "Reset" button)
1 USB 2.0 port (on upper side)
1 sata slot (power + data) for 2.5'' drives (upper side)
2 USB 3.0 ports from a controller on PCIe x1 of the SoC
1 full-size SDcard slot (fits a whole SD card into it)

This device supports the (linux-only) kwboot tool to send
a new uboot over serial console, so it is easy to unbrick
in case the uboot is erased and the device won't boot.

-----
Install instructions:
-----
Since it's not possible to get ssh access to these
devices, the only way to take control is to
solder pins to get TTL serial access.

Case can be opened by removing screws beneath two rubber
feet at back of device, then lifting while prying the
sides of the upper part out to unhook a latch on each
side about 2/3rds of the way toward the front.

Serial connection pins are those labeled "J11", left
of SD as you face SD opening.
Pins are (from left to right, i.e. the first in the list
is the nearest to the SD slot) GND, Rx, Tx.
Do not connect +V pin if you use a USB (self-powered)
TTL-to-USB dongle. Any USB TTL-to-USB converter will work.
Baud rate is 115200, parity "none", databits "8",
flow control "none".

Stock uboot is unable to read ubi partitions (nor usb)
so we will replace it first with our uboot.

Start a TFTP server at IP address 169.254.254.254, and
place the uboot.kwb file in the folder of the server.

Start the serial session and then power up the device.

As soon as you see text on the serial start pressing random
letter keys to stop the boot process.

If you see something like the following line you can proceed:

CE>>

Otherwise if text is still scrolling by you missed the
opportunity, pull the plug and try again.

write

printenv ethaddr

The uboot will write something like this:

ethaddr=00:50:43:00:02:02

This is the device's MAC address, also present in the sticker
under the device.

Write this down as we will need to add it in the
new uboot configuration.

Use the following commands to load the new uboot:

tftp 0x20000 u-boot.kwb

If the uboot confirms that the transfer was successful,
then you can write it to flash with the following commands:

nand erase 0 0x200000
nand write 0x20000 0 0x1c0000

if after the last command the uboot wrote
"xxxx bytes written: OK"
then it was written correctly and we can proceed.

If it did not go well, try again or ask assistence in forums.
Shutting down or rebooting at this time will brick
the device, to unbrick it you will need to use the kwboot
tool from a Linux PC or Virtual Machine.

Now write:

reset

and press enter, the device will reboot and you should see
again text scrolling by.
Press a random key to stop it, and now you should see

pogoplugv4>

We now add the MAC address back, write:

setenv ethaddr '00:50:43:00:02:02'

Confirm that the uboot has understood by writing

printenv ethaddr

If all looks ok, save the setting with

saveenv

At this point the uboot is configured, and we only need to load
the firmware in the flash memory.

Follow the steps below in "Firmware recovery procedure".

----
Firmware recovery procedure
----
The new uboot allows easy recovery from a bad firmware upgrade
where you can't access the device anymore over ssh or luci.

Take a USB flash drive formatted as FAT32, and copy the
initramfs image file in it (it will have "initramfs" in the
file name), then rename it as "initramfs.bin".

Insert the USB drive in the USB 2.0 port of the pogoplug
(the port at the top).

Power up the device, and wait for it to finish booting.

The uboot should find and load the "initramfs.bin"
from usb and if you are connected with serial you should
see the linux kernel boot log (text scrolling by).
Once it is done, press Enter and you will be greeted by
the OpenWRT banner.

If you were not connected with serial just wait a bit and,
you will be able to access it with ssh or luci web interface
(once you find its IP).

The recovery "initramfs" images are run from RAM, so you will
have to do a normal sysupgrade (firmware upgrade) to write
a firmware image to flash memory.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-01-09 22:06:55 +01:00
Alberto Bursi
f5d267df63 uboot-kirkwood: add uboot for pogoplug v4
add an uboot able to boot a kernel in an ubi partition

This uboot also has a "recovery" feature, before
booting from flash it will try to boot a initramfs
image called "initramfs.bin" from a FAT32-formatted
USB drive connected to the USB 2.0 port.
(u-boot lacks drivers for usb 3.0 controllers)

Just rename the initramfs image and place it on
the usb drive, the uboot will load it.

In case there is no USB drive or no such file
is found, the uboot will boot from internal flash.

The whole check takes less than a second, boot times
are not impacted.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-01-09 22:06:55 +01:00
Mathias Kresin
f5df635ccf kirkwood: sync image filename with boardname
Use <manufacturer>_<modelname> as image name.

Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin
c9e2c35f46 kirkwood: use the generic board detect
Drop the target specific detection function in favour of the generic
one provided by base-files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin
aa6f5f1787 kirkwood: use image metadata
Append and enforce image metadata. Remove the device specific image
checks, they are replaced by image metadata.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin
2f757f6035 uboot-kirkwood: fix default u-boot selection
Build the Seagate GoFlexHome u-boot for the Seagate GoFlexNet as well. The
name clearly indicates that the u-boot can be used for both boards

Build the Zyxel NSA310 u-boot if the NSA310B image is selected.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin
a10ab9d843 kirkwood: fix nsa310b compatible strings
Use a destinct compatible string fro the nsa310b.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin
18ea058258 kirkwood: fix compatible string in ib62x0 dts
There is no point in being that specifc in a generic dts covering a range
of boards. Keep only the the generic compat string to use it for a
devicetree based boardname.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin
0ebdf0c1d3 kirkwood: drop support for orphaned boards
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin
d2e18dae28 kirkwood: cleanup image build code
Drop NAND_BLOCKSIZE, UBI_OPTS and UBIFS_OPTS. They are either used by
not supported filesystems or by the legacy image build code.

Add common used options/images to the default build code and override
the options where necessary.

Don't export the kernel image, it isn't required by any board.

While at it, change the file extension for the sysupgrade images to bin.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin
f0227af5d6 ipq806x: drop kernel 4.4 leftovers
Remove the kernel 4.4 specific devicetree source files.

Fixes: 3a3564ead5 ("ipq806x: remove v4.4 support")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:37 +01:00
David Bauer
daae09f1e5 ar71xx: fix Archer C7v4 5GHz MAC-address
The TP-Link firmware uses (primary_mac-1) as MAC-address
for the 5GHz WiFi. This applies the same behaviour to LEDE.

Currently, the MAC-address is retrieved from eth1, which
does not exist on the Archer C7 v4. As a result from this,
every C7 v4 with LEDE carries the same MAC-Address on the 5GHz WiFi.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-01-09 22:05:46 +01:00
Chuanhong Guo
a657978fe7 ramips: fix lenovo newifi-y1 switch and LED config
There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on
port4.

Use a standalone switch configuration to match this and use the switch
trigger so that LAN LED could indicate the connetction status for both
lan ports correctly.

This patch also drop the internet led configuration, because there is a
WAN led for port4 and eth0.2 isn't always used as WAN.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-01-09 22:05:46 +01:00
Mathias Kresin
6912e55e71 ramips: add missing soc compatibles to dts
Add SoC compatibles where missing.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:05:46 +01:00
Mathias Kresin
3326e36fa7 ramips: firewrt: indicate boot status via LED
Add the Firefly FireWRT gree power LED to diag.sh to indicate the boot
status via the power LED.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:05:46 +01:00
Mathias Kresin
e66c47fb14 base-files: gpio switch: set output value with direction
Use the "low" and "high" values to configure the GPIO as an output with
that initial value. It ensures that the gpio doesn't have a unwanted value
during the time the direction is set to ouput and the actual value is
applied.

We don't need to take care of the GPIO polarity for now, since our
exported GPIOs are always active low.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:05:46 +01:00
Mathias Kresin
ff874b656b base-files: gpio_switch: start before boot state done is set
Start gpio_switch before the boot state is set to up/initialised/done.
This way the exported GPIOs are available at the time rc.local is started.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:05:46 +01:00
Gabor Juhos
82cc439976 ar71xx: remove obsolete '< KERNEL_VERSION(4, 4, 0)' check
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.4.0 is always
false. Remove the obsolete check from mach-rb4xx.c to clean up the code
a bit.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 21:33:19 +01:00
Gabor Juhos
8f44c8086b ar71xx: remove obsolete '< KERNEL_VERSION(4, 2, 0)' check
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.2.0 is always
false. Remove the obsolete check from ag71xx_main.c to clean up the code
a bit.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 21:33:18 +01:00
Gabor Juhos
7a4930b27c ar71xx: remove obsolete '< KERNEL_VERSION(3, 15, 0)' checks
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 3.15.0 is always
false. Remove the obsolete checks from the target specific source files
to clean up the code a bit.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 21:33:18 +01:00
John Crispin
aa100b66f2 armvirt: bump to v4.14
Signed-off-by: John Crispin <john@phrozen.org>
2018-01-09 14:40:54 +01:00
John Crispin
7172ec1e8f malta: bump tp v4.14
Signed-off-by: John Crispin <john@phrozen.org>
2018-01-09 10:26:16 +01:00
John Crispin
4ee195bcfa malta: fix image prefix names
Signed-off-by: John Crispin <john@phrozen.org>
2018-01-09 10:26:16 +01:00
Gabor Juhos
99be4170cb ar71xx/mikrotik: disable TP-Link TL-WR810N v2 board support
It does not belongs to the MikroTik boards.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Gabor Juhos
7f7eb18455 ar71xx/mikrotik: disable unused MTD partitioning and split drivers
Reduces the compressed kernel size by ~2.5KB.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Gabor Juhos
660ee2d0f0 ar71xx/mikrotik: disable unused ethernet switch and phy drivers
Disable the drivers for the following ethernet switches:
  Realtek RTL8306
  Realtek RTL8366/8367
  Marvell 88E6060 (DSA)
  Marvell 88E6063 (DSA)

Also disable the phy driver for Marvell PHYs.

None of the supported RouterBOARDs are using any device
which needs these drivers.

Disable the DSA framework too, because it is not required
by the remaining switch drivers.

This reduces the compressed kernel size by ~20KB.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Gabor Juhos
b386b5727b ar71xx: fix Kconfig dependency of the 88E6063 switch DSA driver
The Marvell 88E6063 ethernet switch driver depends on the DSA
framework. Add a 'depends on NET_DSA' statement to its Kconfig
entry to state that explicitly.

Fixes the following Kconfig warning:

  warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6063) selects NET_DSA_TAG_TRAILER which has unmet direct dependencies (NET && NET_DSA)

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Gabor Juhos
09bb7105c2 ar71xx: sort kernel configurations
The symbols in some kernel configurations of the target are in
wrong order. Sort them with kconfig.pl.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Stijn Tintel
56767dfa42 octeon: add support for kernel 4.14
Tested on EdgeRouter Lite.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-01-08 20:14:57 +02:00
Stijn Tintel
aa399b4e27 kernel: bump 4.14 to 4.14.12
No patch refresh required.

Compile-tested on: octeon, x86/64.
Runtime-tested on: octeon, x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-01-08 20:13:03 +02:00
Hauke Mehrtens
f1fb710483 lantiq: activate noise margin delta for VDSL too
Previously this was only activated for ADSL, this patch activates the
same setting also for VDSL, this feature is also support for VDSL in the
same way it works for ADSL.
I tested it with DSL FW 5.7.9.5.1.7 against a Broadcom 177.140 DSLCO
(Deutsche Telekom) and saw different data rates and Max. Attainable Data
Rates depending on the ds_snr_offset settings I choose.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-07 23:42:54 +01:00
Matthias Schiffer
ca04884262
uboot-envtool: remove superfluous + sign from PKG_BUILD_DEPENDS
A + sign does not have meaning in build depends.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-07 19:52:05 +01:00
Jo-Philipp Wich
f089b1fda2 libubox: fix package bump
The previous commit was incorrectly rebased and referred to a not
yet existing PROJECT_GIT variable.

Fixes: d86a269c1f libubox: update to latest git HEAD
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-07 16:34:29 +01:00
Jo-Philipp Wich
d86a269c1f libubox: update to latest git HEAD
1c08e80 jshn: properly support JSON "null" type

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-07 16:28:22 +01:00
Jo-Philipp Wich
4e9af67077 Revert "fstools: update to latest git HEAD"
This reverts commit df326e9b2e.

The referenced commit does not exist in the upstream repository.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-07 13:42:46 +01:00
John Crispin
df326e9b2e fstools: update to latest git HEAD
2a9a6ea libfstools: optimize building directory string for glob
de6b026 libfstools: support file paths longer than 255 chars

Signed-off-by: John Crispin <john@phrozen.org>
2018-01-07 13:05:40 +01:00
Gabor Juhos
4045f15a21 ar71xx: fix compiler warnings in mdio-bitbang.c for 4.4
Building Linux 4.4 for ar71xx throws the following warnings in
drivers/net/phy/mdio-bitbang.c:

    CC      drivers/net/phy/mdio-bitbang.o
  In file included from include/linux/irqflags.h:14:0,
                   from drivers/net/phy/mdio-bitbang.c:20:
  drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_read':
  include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
    (void)(&__dummy == &__dummy2); \
                    ^
  include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
     typecheck(unsigned long, flags); \
     ^
  include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
     raw_local_irq_save(flags);   \
     ^
  drivers/net/phy/mdio-bitbang.c:162:2: note: in expansion of macro 'local_irq_save'
    local_irq_save(flags);
    ^
  include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
    (void)(&__dummy == &__dummy2); \
                    ^
  include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
     typecheck(unsigned long, flags); \
     ^
  include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
   #define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
                                         ^
  drivers/net/phy/mdio-bitbang.c:175:2: note: in expansion of macro 'local_irq_restore'
    local_irq_restore(flags);
    ^
  drivers/net/phy/mdio-bitbang.c:159:11: warning: unused variable 'i' [-Wunused-variable]
    int ret, i;
             ^
  In file included from include/linux/irqflags.h:14:0,
                   from drivers/net/phy/mdio-bitbang.c:20:
  drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_write':
  include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
    (void)(&__dummy == &__dummy2); \
                    ^
  include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
     typecheck(unsigned long, flags); \
     ^
  include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
     raw_local_irq_save(flags);   \
     ^
  drivers/net/phy/mdio-bitbang.c:185:2: note: in expansion of macro 'local_irq_save'
    local_irq_save(flags);
    ^
  include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
    (void)(&__dummy == &__dummy2); \
                    ^
  include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
     typecheck(unsigned long, flags); \
     ^
  include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
   #define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
                                         ^
  drivers/net/phy/mdio-bitbang.c:200:2: note: in expansion of macro 'local_irq_restore'
    local_irq_restore(flags);
    ^

These are caused by the 900-mdio_bitbang_ignore_ta_value and
901-phy-mdio-bitbang-prevent-rescheduling-during-command patches.

The first patch removes some code but it does not remove the variable
which is used by the removed code only.

The second patch adds local_irq_{save,restore} calls. The type of the
argument of these calls must be 'unsigned long', but the patch defines
the variable as 'long'.

Fix both patches to silence the warnings.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-07 13:05:40 +01:00
Jo-Philipp Wich
6e4fa5d1a3 hostapd: bump PKG_RELEASE after 802.11w changes
Fixes: 8a57531855 "hostapd: set group_mgmt_cipher when ieee80211w is enabled"
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-07 12:42:45 +01:00
Jo-Philipp Wich
34e9937f2a kernel: fix packaging of kmod-gpio-nxp-74hc164
The NXP 74HC164 GPIO expander driver uses a different config symbol
("CONFIG_GPIO_74X164") and module name since since at least Kernel
version 2.6.37.

Update the kmod package definition accordingly by adjusting kconfig
and module file names.

This unrelated, but correct change has been separated from the
WNR2000v5 support commits.

Ref: https://github.com/lede-project/source/pull/1256
Suggested-by: Raphael Catolino <raphael.catolino@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-07 12:33:47 +01:00
Jo-Philipp Wich
3f5e39e960 zlib: only enable NEON optimizations on eligible targets
Instead of inferring the availability of NEON support from the target
optimization flags, use a preprocessor test to decide whether to enable
ARMv8 NEON optimizations.

Fixes the following build error spotted by the mediatek/32 buildbot:

    [ 26%] Building C object CMakeFiles/zlib.dir/contrib/arm/inflate.o
    In file included from .../zlib-1.2.11/contrib/arm/chunkcopy.h:10:0,
                     from .../zlib-1.2.11/contrib/arm/inflate.c:87:
    .../arm_neon.h:31:2: error: #error You must enable NEON instructions (e.g. -mfloat-abi=softfp -mfpu=neon) to use arm_neon.h
     #error You must enable NEON instructions (e.g. -mfloat-abi=softfp -mfpu=neon) to use arm_neon.h
      ^
    In file included from .../zlib-1.2.11/contrib/arm/inflate.c:87:0:
    .../zlib-1.2.11/contrib/arm/chunkcopy.h:18:9: error: unknown type name 'uint8x16_t'
     typedef uint8x16_t chunkcopy_chunk_t;
             ^
    [...]
    CMakeFiles/zlib.dir/build.make:302: recipe for target 'CMakeFiles/zlib.dir/contrib/arm/inflate.o' failed

Fixes: 3acecba520 "package/libs/zlib: Add ARM and NEON optimizations"
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-07 12:33:47 +01:00
Jo-Philipp Wich
8a57531855 hostapd: set group_mgmt_cipher when ieee80211w is enabled
In order to properly support 802.11w, hostapd needs to advertise a group
management cipher when negotiating associations.

Introduce a new per-wifi-iface option "ieee80211w_mgmt_cipher" which
defaults to the standard AES-128-CMAC cipher and always emit a
"group_mgmt_cipher" setting in native hostapd config when 802.11w is
enabled.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-07 12:33:47 +01:00
Kevin Darbyshire-Bryant
b153dbf046 argp-standalone: clean up patch fuzz
Refresh patches to tidy up fuzz.  No functional changes

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-01-05 11:59:59 +01:00
Kevin Darbyshire-Bryant
4e800716ac lua: clean up patch fuzz
Refresh patches to tidy up fuzz.  No functional changes

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-01-05 10:42:34 +01:00
Kevin Darbyshire-Bryant
b61a648e4a busybox: clean up patch fuzz
Refresh patches to tidy up fuzz.  No functional changes

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-01-05 10:35:51 +01:00
Mathias Kresin
d726187367 lantiq: fix wbmr-hp-g300h image metadata
The Annex A and Annex B version are using the same (old) userspace
boardname. Update the SUPPORTED_DEVICES to allow an update from lede-17.01.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-04 21:23:59 +01:00
Matthias Schiffer
0b28cc56d4
scripts/package-metadata.pl: remove broken detection of self-dependencies
A self-dependency is not an error worth a warning; rather, it is very
common: whenever there are dependencies between different binary packages
originating from the same source package, such dependencies occur. Not
actually generating dependency rules is correct, but already handled a few
lines below.

A typo prevented this redundant rule from working, which is the reason the
warning was not actually printed.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-04 17:18:16 +01:00