Drop the "-x lzo" compression type override from MKUBIFS_OPTS since we
do not support it in mkfs.ubifs. Attempting to use LZO compression results
in "Error: bad compressor name".
The build system also appends an explicit "--compr=zlib" to the mkfs command
line, turning the "-x" flag into a no-op anyway.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The subtarget configurations contained a lot of reduntant symbols, arbitrary
overrides and symbols set to =m.
Remove most of these redundant settings to shrink the subtarget configurations
to a manageable size.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes the following error spotted by the buildbot:
Package kmod-fs-squashfs is missing dependencies for the following libraries:
xz_dec.ko
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Make the call to of_mdiobus_register() dependant on CONFIG_OF to avoid
pulling in an unwanted dependency on of_mdio.ko.
Fixes: 3dc523f232 kernel: add OF support to rtl8355 driver
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fix ART offset (make it universal for 8/16 MB versions of the board) and
while at it, include also GPIO setup for h/w watchdog (EM6324QYSP5B).
Fixes: FS#1532
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The biggest (and the only?) disadventage of this is obviously an
increased image size.
For mips74k the size of vmlinux goes up from 4186684 B to 4701436 B.
Most devices use LZMA compressed kernel so probably more important is
vmlinux.lzma size which goes up from 1342945 B to the 1508498 B.
Still this isn't something that should stop target kernel bump. There
are various adventages of kernel 4.14. If kernel / image size is a
serious concern for anyone, it's perfectly possible to use previous
release which is pretty solid for the brcm47xx.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Paul Wassi <p.wassi@gmx.at>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Splitted out the dts file and create the new dts for the 256 MByte RAM and
the 512 MB RAM version.
Migrate both versions to the common board detection.
The install the 512 MByte Version on a board running the 256 MByte image,
a forceful sysupgrade with the -F flag is required.
Signed-off-by: Davide Ammirata <list@davidea.it>
The RavPower WD03 is a battery powered SD card reader and a USB port.
Specifications:
SOC: MediaTek MT7620N
BATTERY: 6000mah
WLAN: 802.11bgn
LAN: 1x 10/100 Mbps Ethernet
USB: 1x USB 2.0 (Type-A)
RAM: PM Tech PMD708416CTR-5CN 32 MB
FLASH: Holtek HT66F40 - 8 MB Flash
LED: Power button and 4 leds to indicate power level of the
battery (could not get control of that)
INPUT: Power, reset button
OTHER: USB SD-Card reader with card detect on GPIO#42
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Installation:
- Download the sysupgrade image
- Place it in the root of a clean TFTP server running on your computer.
- Rename the image to "kernel" — be sure there is no file extension.
- Plug the WD03 into your computer via ethernet.
- Set your computer to use 10.10.10.254 as its IP address.
- With your WD03 shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The WD03 (10.10.10.128) will look for your computer at 10.10.10.254
and install the kernel file. Once it has finished installation of the
kernel file, it will search for a (nonexistent) rootfs file — when it
begins searching for this file, shut down the WD03 by holding the
power button normally.
- Start up your WD03 normally.
Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
Backport patch accepted upstream which removes the reset asserts of the
xrx200 gphy driver on reboot/remove.
While doing a global software reset, these bits are not cleared and let
some bootloader fail to initialise the GPHYs. The bootloader don't expect
these bits to be set, as they aren't during power on.
The asserts were a workaround for a wrong syscon-reboot mask. With a mask
set which includes the GPHY resets of the first reset register, the
resets of the second reset register arn't required any more.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Some of the new ath79 device trees were missing read-only tags on the
u-boot partitions. This adds the tags where previously missing.
Signed-off-by: Russell Senior <russell@personaltelco.net>
This new syntax is slightly better designed & uses "compatible" string.
For details see Documentation/devicetree/bindings/mtd/partition.txt .
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
Not working:
- USB port
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
Some maintainers prefer DTS files licensed under permissive license like
MIT / BSD. As all DT bindings should be OS independent and DTS files are
pretty separated from Linux code it probably makes sense to share them
across projects.
The safest solution is to use dual licensing: that way it stays clear
these files can be used in GPL projects without depending on current
belief of licenses compatibility.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: John Crispin <john@phrozen.org>
This target aims to replace ar71xx mid-term. The big part that is still
missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik
subtargets will follow.
Signed-off-by: John Crispin <john@phrozen.org>
This switches bcm53xx from spi-bcm53xx to the spi-bcm-qspi driver. The
later one was developed by Broadcom and is more advanced one. It
supports more modes, setting a speed, setting bits per word and uses
IRQs instead of polling.
This increases kernel size from 1808120 B to the 1811160 B (by 3040 B).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This adds an interrim patch for v4.14 based on an
upstream commit to get ethernet working on D-Link DNS-313
(probably also on the Wiliboards)
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the D-Link devices boot from hard disk we need to
add the following changes to Gemini:
- Supply a bootarg in the device tree so we can boot from
the right partition (/dev/sda4 on DNS-313)
- Disable forced command line in config so the kernel picks
up the right bootargs from the device tree
- Enable EXT4 in the config as this is used for rootfs else
we get nowhere, we cannot load this as a module because,
well, it is supposed to be loaded from the root partition
(chicken and egg problem).
- Enable jbd2 and mbcache (needed by ext4)
Also clean out the premature attempts to dynamically
modify the command line in the Image makefile: we should
pass this with the device tree bootargs instead, it works
much better.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Disable video and input drivers - they are needed only for one
board and can be enabled via modules if/when UI will be available.
Use LED drivers from packages.
Cleanup other things unnecessarily overriding defaults.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
This adds the patches to get fairly complete Gemini support
using kernel v4.14. It is mainly a backport of patches from
kernel v4.16 with omissions of things like graphics that require
substantial changes and will be better handled once we move
to the v4.16 kernel proper.
On top of this are some WIP patches for USB support.
Tested on Raidsonic NAS4220B and D-link DNS-313.
ChangeLog v4->v5:
- Fix ethernet single gmac usecase
- Fix USB reset (patch from Hans)
- Fix Raidsonic ethernet skew delay
- Fix kernel config (bridge, squashfs, jffs2, usb)
- Disable second usb port on Raidsonic board until fotg210_hcd is fixed
ChangeLog v3->v4:
- Make sure to use tabs rather than spaces in base-files.
- Use the dns313 image tool from the firmware-utils.
- Break out the addition of the v4.14 patches and the removal
of the v4.4 patches to separate (big) patches.
ChangeLog v2->v3:
- Update the kernel config as indicated by Hauke Martens:
- Regenerate again after rebasing using kernel_oldconfig
dropping a few optimization settings that are now generic
- Drop CFG80211 stuff (module)
- Drop CIFS stuff (module)
- Drop MAC80211 (module)
- Drop wireless drivers (module)
- Enabled OverlayFS
- Added proper DNS-313 boot image generation with the special
file header tool.
- Disable CMA in the kernel
- Enable LZMA compression of the kernel
- Consequently name the nas4220b images nas4220b
- Update preinit MAC detection script to handle also DNS-313
- Add board.d/03_hdparm to set the disk to spin down after
1 minute by default, if we have the hdparm tool installed
ChangeLog v1->v2:
- Processed config through kernel_oldconfig
- Processed patches through make target/linux/{clean,refresh} V=99
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
1. able to set neon flags to sama5d2 & sama5d4 subtargets.
2. fix the make clean which removes all the subtargets in bin folder.
3. able to configure kernel specific to subtarget.
4. able to set vfpu4 flags to samad3 subtargets.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
creating sdcard image with ext4 rootfs only and ignoring creating
other filesystem in sdcard image.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
copying at91bootstrap and uboot binaries to sdcard image is done
based on device name instead of dts name and this avoids creating
multiple u-boot and at91bootstrap binaries.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
In typical OpenWrt setups, there are no other users that have a shell spawned for them by default.
This can be overriden by the kernel.dmesg_output syssctl.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
sama5d2 & samad4 have neon feature and sama5d3 does not have neon
feature due to which sama5d3 boot fails with error message Kernel
panic - not syncing: Attempted to kill init! exitcode=0x00000004.
removing neon & VFPv4 support to fix this
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
when external kernel is selected from menuconfig, device wb50n is not
avaliable and build fails. As a fix adding checks for external kernel.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Kernel support already present.
Patch adds userspace for the 'iLS' suffix model of the RB2011 family.
Enables correct initial switch settings, sysupgrade, etc.
https://mikrotik.com/product/RB2011iLS-IN
Signed-off-by: Simon Paterson <simon.paterson.nz@gmail.com>
The harden branch predictor was backported for arm64 with 4.9.92-96.
Fixes: 9aa196e0f2 ("kernel: bump 4.9 to bump 4.9.96")
Signed-off-by: Mathias Kresin <dev@kresin.me>
