This commit modifies the /lib/netifd/proto/gre.sh script so that, when
GRE-TAP tunnels are created, either IPv4 or IPv6, the prefix before the chosen
interface name contains the "tap" substring, to differentiate them from non-TAP
GRE tunnels.
Right now, both GRE and GRE-TAP tunnel (either IPv4 or IPv6) interfaces defined
in /etc/config/network are named equally ("gre-"+$ifname or "grev6"+$ifname)
upon creation. For instance, the following tunnels:
config interface 'tuna'
option peeraddr '172.30.22.1'
option proto 'gre'
config interface 'tunb'
option peeraddr '192.168.233.4'
option proto 'gretap'
config interface 'tunc'
option peer6addr 'fdc5:7c9e:e93d:45af::1'
option proto 'grev6'
config interface 'tund'
option peer6addr 'fdc0:6071:1348:31ff::2'
option proto 'grev6tap'
are named, respectively, "gre-tuna", "gre-tunb", "grev6-tunc" and "grev6-tund".
The current change makes that each GRE tunnel interface of the four different
types available (gre, gretap, grev6 and grev6tap) gets a different prefix.
Therefore, the abovementioned tunnels will be named, respectively:
"gre4-tuna", "gre4t-tunb", "gre6-tunc" and "gre6t-tund".
This is coherent with other types of virtual interfaces (i.e. PPP, PPPoE, PPPoA)
where the whole protocol name is used. For instance, a PPPoA interface named
"p1" and a PPPoE interface named "p2" will respectively appear as "pppoa-p1"
and "pppoe-p2", not as "ppp-p1" and "ppp-p2").
Since Linux interfaces names are limited to 15 characters, these prefixes leave,
for the worst case (TAP tunnels), 9 characters for the actual name.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Build seems to fail with:
```
Collected errors:
* satisfy_dependencies_for: Cannot satisfy the following dependencies for X:
* grev4 *
* opkg_install_cmd: Cannot install package X
```
After adding an empty install rule, the failure goes away.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Source package gre was depending on kmod-ip6-gre, however the actual
kernel module package that is created is kmod-gre6. Therefore
update (source) package gre for ipv6 gre support.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 48100
Since r46834, IPv6 support is builtin if selected. Therefor, dependencies
on kmod-ipv6 can no longer be fulfilled, since it is not a module anymore.
Signed-off-by: Arjen de Korte <arjen+openwrt@de-korte.org>
SVN-Revision: 47022
Tos support is added as a generic grev4/grev6 parameter which can have the following values :
-inherit (outer header inherits the tos value of the inner header)
-hex value
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42700
The package supports Generic Routing Encapsulation support by registering following protocol kinds:
-gre
-gretap
-grev6
-grev6tap
Following options are valid for gre and gretap kinds:
-ipaddr
-peeraddr
-df
-mtu
-ttl
-tunlink
-zone
-ikey
-okey
-icsum
-ocsum
-iseqno
-oseqno
The gretap kind supports additionally the network option
Following options are valid for grev6 and grev6tap kinds:
-ip6addr
-peer6addr
-weakif
-mtu
-ttl
-tunlink
-zone
-ikey
-okey
-icsum
-ocsum
-iseqno
-oseqno
The grev6tap kind supports additionally the network option
Typical network config for a GREv4 tunnel :
config interface 'gre'
option peeraddr '172.16.18.240'
option mtu '1400'
option proto 'gre'
option tunlink 'wan'
option zone 'tunnel'
Typical network config for a GREv4 tap tunnel :
config interface 'gretap'
option peeraddr '195.207.5.79'
option mtu '1400'
option proto 'gretap'
option zone 'tunnel'
option tunlink 'wan'
option network 'wlan_ap'
I added myself as maintainer for the moment; feel free to change.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 41897
