Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
SOC: BCM63168 (BMIPS4350 V8.0 @400MHz)
Flash size: 16 MiB
RAM size: 128 MiB
Heavily based on patch for OpenWRT Chaos Chalmer.
Original patch and more info can be found at:
https://openwrt.org/toh/sky/sr102
Known issues:
- Wireless and ADSL modem are not working.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
Add support for the Sercomm AD1018 router
This a BCM6328 based board, 128 MB RAM, 128 MiB NAND flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1 USB
host port (not soldered). The board also has an FXS chip (Si32177)
connected via SPI (SS2#), without support in LEDE.
Since NAND flash chips aren't still supported in brcm63xx, the
support is for now added to work only with SPI flash chips. Therefore
hardware modding, soldering a new SPI flash chip, is required
to make the board work with LEDE (tested and working OK).
The flash at dts is intentionally left without partitioning to let
the user choose a NOR chip of any size (8, 16 or 32 MB).
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: renamed ad1018 to ad1018-nor to signify the modification]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for the Comtrend AR-5315u router
This a BCM6318 based board, 64 MB RAM, 16 MB SPI flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1
USB host port
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: refreshed patch]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
SOC: Broadcom BCM6368 (2 * Broadcom BMIPS4350 V3.1 / 400 MHz)
Flash size: 32MB (split 16/16 dual boot)
RAM size: 64MB
Wireless: BCM432x 802.11a/b/g/n(pci)
Ethernet: Broadcom BCM53115
USB: 1 x USB 2.0
Known issues:
- Unable to detect 53115 switch attached to MDIO. Not supported
- No support for the cable port
More info on the device and the research can be found at:
http://www.actiontec.com/212.html
Same FCC ID as:
https://wikidevi.com/wiki/Actiontec_V1000H_(Telus)
Signed-off-by: Anthony Sepa <anthonysepa@yahoo.ca>
[jonas.gorski: fix commit subject/message]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Build profile for Asmax AR 1004g refers to an invalid DTS "rg100a". The
correct DTS for this device is "ar1004g".
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Add support for the Observa Telecom VH4032N router.
This is another BCM6368 router, 128 MB RAM, 32MB flash and 3 USB
host ports.
The wifi chip is an onboard Broadcom BCM43222.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: use gpio-hog instead of abusing ephy-reset]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
BCM6362 and BCM3380 seem to share the same PRID. Disable serial output
for them until we can find a way to tell them apart reliably.
Fixes: 8f3cfe4ba2 ("brcm63xx: lzma-loader: add BCM3380 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This patch adds support for the ADB P.DG AV4202N aka Pirelli PRG AV4202N.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The imagetag RSA signature field may not exceed 20 characters, so trim the
Git hash portion from the REVISION variable in order to ensure that the
resulting string fits within this field.
The current revision values may be longer than 20 chars, especially when
building within a dirty tree. In this case, the revision will look like
"r2435+75-b4aa3c8" which, combined with the "LEDE-" prefix, is 21 chars long.
Fixes the following error spotted by the buildbots:
Error: RSA Signature (rsa_signature,r) too long.
make[4]: *** [.../lede-brcm63xx-generic-NEUFBOX6-squashfs-cfe.bin] Error 1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fix Image generation for the Livebox 1
- missing "relocate-kernel", wrong "LOADADDR", fix it
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Defer the CFE_EXTRAs evaluation to allow overriden BLOCK_SIZE and
IMAGE_OFFSET take effect, and replace the unused IMAGE_SIZE with
IMAGE_OFFSET in DEVICE_VARS.
This fixes image generation for targets using different offsets or
blocksizes.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Instead of having CFE_EXTRAS for every device that need specific block sizes
and image offset, let's define a couple of vars which can be customized for
each device.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Some devices require padded images in order to prevent CFE from flashing them
to the wrong offset.
For small flashes (4/8) this is no big deal, but for larger flashes (16/32) this
implies 8 and 16 MB images, which is way too large and some devices aren't
capable of flashing them through sysupgrade.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The only difference is a field in the image tag header, so just define
two images for it instead of treating them as separate devices.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
- Use KERNEL_INITRAMFS_SUFFIX for customizing initramfs name.
- Modifying $(PROFILES) is no longer needed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch adds support for the Netgear EVG2000 VoIP Gateway to the
bcm63xx targets.
This device was not sold to the general public, but rather is/was
provided by telcos to customers in Sweden, Australia, Singapore and
other parts of asia.
Known issues:
- Unable to detect 53115 switch. This appear to be a problem with
probing for the PHY using MDIO and results in error 5. Doesn't seem to
be a problem with the configuration, and could use someone with
experience to have a look at it.
- Uses the b43 driver as using the OpenWRT/LEDE broadcom-wl driver
fails to load the firmware for the 4322, so 802.11n is not supported.
More info on the device and the research can be found at:
https://wiki.openwrt.org/toh/netgear/evg2000https://wikidevi.com/wiki/Netgear_EVG2000https://github.com/Xotic750/mirror-lede/tree/evg2000https://forum.openwrt.org/viewtopic.php?id=63950
Signed-off-by: Graham Fairweather <xotic750@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
According to the calling convention of the o32 ABI the caller
function must reserve stack space for $a0-$a3 registers in case
the callee needs to save its arguments.
The assembly code of the loader does not reserve stack space for
these registers thus when the 'loader_main' function needs to save
its arguments, those will be stored in the 'workspace' area instead
of the stack.
Because the workspace area is also used by other part of the code, the
saved register values gets overwritten and this often leads to failed
kernel boots.
Fix the code to reserve stack space for the registers to avoid this
error.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
[noltari: apply the fix for brcm63xx too]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48979
This patch adds support for the NuCom R5010UNv2.
It's a BCM6328 based board. It has an onboard BCM43217 wifi chip. For this
wifi chip looks like the brcmsmac driver isn't still supported, b43 drivers are used
for the profile of the router.
It's worth mentioning this board was affected by a bug solved with
https://dev.openwrt.org/changeset/46707
Tested-by: Angel Fontan <angel.fontan@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47697
Add support for Comtrend VR-3026e v1.
The device is almost identical to the Comtrend VR-3025un.
Signed-off-by: Martin Tesar <tesarmar@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46752
Make the device name accessible for any build commands instead of
forcing targets to define it themselves.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46597
Instead of letting each target define it themselves, create on in
include/image.mk and let the targets use it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46596
BCM6318: add support for Plusnet / Sagem 2704N (V1)
Signed-off-by: Matt Goring <matt.goring@googlemail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46562
Switches BCM63xx to the new IB system.
Images are generated per device definitions.
There are no changes in the produced images except for some name changes,
caused by the new IB system.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46490
Simplify image/Makefile by using the new perl script for RedBoot.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46489
Now that we have a BuildDTB command, make use of it instead of calling
dtc directly.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46390
To improve reproducibility, prevent the inclusion of timestamps
in the gzip header.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 46361
When r42245 moved A4001N to DT based detection the image padding size
was accidentally increased from 4 to 8 MiB. This made images unflashable
on these devices.
Fixes#19836.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45945
